Thin-film lithium niobate-based electro-optic comb cloning for self-homodyne coherent communication.

As the optical communication industry advances, metropolitan area networks (MANs) and radio access networks (RANs) are extensively deployed on a large scale, demanding energy-efficient integrated light sources and simplified digital signal processing (DSP) technologies. The emergence of thin-film lithium niobate (TFLN) has given rise to high-performance, energy-efficient on-chip modulators, making on-chip optical frequency comb (OFC) more appealing. Owing to the phase uniformity and stability of this chip-scale device, it has been possible to eliminate the carrier frequency phase estimation (CPE) in DSP stacks using comb-clone-enabled self-homodyne detection. Here we report the first use, to our knowledge, of a TFLN on-chip electro-optic (EO) frequency comb to realize comb cloning and self-homodyne coherent detection. We transmit three optical pilot tones and eight data channels encoded with 20 Gbaud polarization-multiplexed 16-ary quadrature amplitude modulation (PM-16-QAM) over 10 km and 80 km standard single-mode fibers. The bit error ratios (BERs) of the eight channels reach below 10-3, a result made possible by our on-chip comb. The scalability and mass producibility of on-chip EO combs, combined with the simplified DSP, show potential in our proposed fifth-generation (5G) RAN and MAN transmission scheme.

Low-phase-noise microwave generation with a free-running dual-pumped Si3N4 soliton microcomb.

Microwave signals can be generated by photodetecting the repetition frequencies of the soliton microcombs. In comparison to other methods, the dual-pumped method allows for the stable generation of the soliton microcombs even with resonators having lower Q-factors. However, introducing an additional pump laser may affect the phase noise of the generated microwave signals when using these dual-pumped soliton microcombs. Here, we investigate the factors that could influence the phase noise of microwave signals generated with dual-pumped soliton microcombs, including the polarization, amplitude noise, and phase noise of the two pumps. We demonstrate a 25.25 (12.63) GHz microwave with phase noise reaching -112(-118) dBc/Hz at a 10 kHz offset frequency, surpassing the performance of previous reports on microwave generation using free-running Si3N4 soliton microcombs, even those generated with higher Q microresonators. We analyze the noise floor of the generated microwave signals and establish a phase noise simulation model to study the limiting factors in our system. Our work highlights the potential of generating low-phase-noise microwave signals using free-running dual-pumped soliton microcombs.

Massively parallel FMCW lidar with cm range resolution using an electro-optic frequency comb.

Frequency-modulated continuous wave (FMCW) light detection and ranging (lidar) is a promising solution for three-dimensional (3D) imaging and autonomous driving. This technique maps range and velocity measurement to frequency counting via coherent detection. Compared with single-channel FMCW lidar, multi-channel FMCW lidar can greatly improve the measurement rate. A chip-scale soliton micro-comb is currently used in FMCW lidar to enable multi-channel parallel ranging and significantly increase the measurement rate. However, its range resolution is limited due to the soliton comb having only a few-GHz frequency sweep bandwidth. To overcome this limitation, we propose using a cascaded modulator electro-optic (EO) frequency comb for massively parallel FMCW lidar. We demonstrate a 31-channel FMCW lidar with a bulk EO frequency comb and a 19-channel FMCW lidar using an integrated thin-film lithium niobate (TFLN) EO frequency comb. Both systems have a sweep bandwidth of up to 15 GHz for each channel, corresponding to a 1-cm range resolution. We also analyze the limiting factors of the sweep bandwidth in 3D imaging and perform 3D imaging for a specific target. The measurement rate achieved is over 12 megapixels per second, which verifies its feasibility for massively parallel ranging. Our approach has the potential to greatly benefit 3D imaging in fields where high range resolution is required, such as in criminal investigation and precision machining.

Air-gap Fabry-Pérot cavity filtered 30 nm broadband electro-optic frequency combs for high-order coherent communications.

Broadband electro-optic (EO) frequency combs, which have flexible and high repetition frequencies, are prospective light sources for dense-wavelength-division-multiplexed coherent optical communications. In most cases, nonlinear spectral broadening and amplification procedures are needed to achieve broadband and high-power EO frequency combs. This leads to a low optical carrier-to-noise ratio (OCNR) for comb lines, limiting the transmission capacity. Here, we propose to use an air-gap Fabry-Pérot (FP) cavity to improve the OCNR for all the comb lines covering a 30 nm broadband spectrum. A 12 dB OCNR (0.1 nm bandwidth) improvement is obtained experimentally via using an FP cavity with ∼790 MHz bandwidth. We apply a 150-channel filtered EO comb with 25 GHz channel spacing and load 20 GBaud signals on each comb line to demonstrate the effect of OCNR improvement. The 137/150 channels have a bit error rate below the threshold of soft-decision forward error correction when using the 128 quadrature amplitude modulation (QAM) format. However, none of these channels can support this modulation format without cavity filtering. We also investigate dispersion tolerance and the long-term stability when using an air-gap FP cavity, highlighting its advantages. Our results show a practical solution to boost the transmission capacity when applying broadband EO combs in optical communications.

Large-scale true-time-delay remote beamforming with EO frequency combs and multicore fiber.

Optical true-time-delay (OTTD) beamforming is a promising solution to support the ultra-broadband radio access network. However, large-scale antenna arrays set at remote radio units require the OTTD counterpart to have corresponding larger-scale channel numbers. Here, we demonstrate an OTTD remote beamforming network with a record 287 channel number using electro-optic frequency combs and multicore fiber. Our proposed scheme can generate beams for both one-dimensional and two-dimensional antenna arrays. We highlight that using multicore fiber not only increases the channel numbers but also supports remote beamforming. We estimate the long-term stability of this remote beamforming network, and 1-ps-level relative time delay variation in 2 h is obtained when using multicore fiber. It is one order of magnitude better than using parallel single-mode fibers. Thus, highly stable beamforming is achieved. These results pave the way for the application of OTTD beamforming in 5G and beyond networks.