Application of the Surface Regression Technique for Enhancing the Input Factors and Responses for Processing Coconut Oil under Vertical Compression.

This study optimized the input processing factors, namely compression force, pressing speed, heating temperature, and heating time, for extracting oil from desiccated coconut medium using a vertical compression process by applying a maximum load of 100 kN. The samples' pressing height of 100 mm was measured using a vessel chamber of diameter 60 mm with a plunger. The Box-Behnken design was used to generate the factors' combinations of 27 experimental runs with each input factor set at three levels. The response surface regression technique was used to determine the optimum input factors of the calculated responses: oil yield (%), oil expression efficiency (%), and energy (J). The optimum factors' levels were the compression force 65 kN, pressing speed 5 mm min-1, heating temperature 80 °C, and heating time 52.5 min. The predicted values of the responses were 48.48%, 78.35%, and 749.58 J. These values were validated based on additional experiments producing 48.18 ± 0.45%, 77.86 ± 0.72%, and 731.36 ± 8.04 J. The percentage error values between the experimental and the predicted values ranged from 0.82 ± 0.65 to 2.43 ± 1.07%, confirming the suitability of the established regression models for estimating the responses.

Assessment of Quality and Efficiency of Cold-Pressed Oil from Selected Oilseeds.

In this present study, an oil press was used to process 200 g each of sesame, pumpkin, flax, milk thistle, hemp and cumin oilseeds in order to evaluate the amount of oil yield, seedcake, sediments and material losses (oil and sediments). Sesame produced the highest oil yield at 30.60 ± 1.69%, followed by flax (27.73 ± 0.52%), hemp (20.31 ± 0.11%), milk thistle (14.46 ± 0.51%) and pumpkin (13.37 ± 0.35%). Cumin seeds produced the lowest oil yield at 3.46 ± 0.15%. The percentage of sediments in the oil, seedcake and material losses for sesame were 5.15 ± 0.09%, 60.99 ± 0.04% and 3.27 ± 1.56%. Sediments in the oil decreased over longer storage periods, thereby increasing the percentage oil yield. Pumpkin oil had the highest peroxide value at 18.45 ± 0.53 meq O2/kg oil, an acid value of 11.21 ± 0.24 mg KOH/g oil, free fatty acid content of 5.60 ± 0.12 mg KOH/g oil and iodine value of 14.49 ± 0.16 g l/100 g. The univariate ANOVA of the quality parameters against the oilseed type was statistically significant (p-value < 0.05), except for the iodine value, which was not statistically significant (p-value > 0.05). Future studies should analyze the temperature generation, oil recovery efficiency, percentage of residual oil in the seedcake and specific energy consumption of different oilseeds processed using small-large scale presses.

Influence of Alkali Treatment of Jatropha Curcas L. Filler on the Service Life of Hybrid Adhesive Bonds under Low Cycle Loading.

The aim of this research was to evaluate the effect of untreated and 5% aqueous NaOH solution-treated filler of the plant Jatropha Curcas L. on the mechanical properties of adhesive bonds, especially in terms of their service life at different amplitudes of cyclic loading. As a result of the presence of phorbol ester, which is toxic, Jatropha oilseed cake cannot be used as livestock feed. The secondary aim was to find other possibilities for the utilization of natural waste materials. Another use is as a filler in polymer composites, that is, in composite adhesive layers. The cyclic loading of the adhesive bonds was carried out for 1000 cycles in two amplitudes, that is, 5-30% of the maximum force and 5-50% of the maximum force, which was obtained by the static tensile testing of the adhesive bonds with unmodified filler. The static tensile test showed an increase in the shear strength of the adhesive bonds with alkali-treated filler compared to the untreated filler by 3-41%. The cyclic test results did not show a statistically significant effect of the alkaline treatment of the filler surface on the service life of the adhesive bonds. Positive changes in the strain value between adhesive bonds with treated and untreated filler were demonstrated at cyclic stress amplitudes of 5-50%. SEM analysis showed the presence of interlayer defects in the layers of the tested materials, which are related to the oil-based filler used.

Determination of Maximum Oil Yield, Quality Indicators and Absorbance Spectra of Hulled Sunflower Seeds Oil Extraction under Axial Loading.

The present study aims to estimate the maximum oil yield of hulled sunflower seed samples in a uniaxial process under a load of 40 kN and speed of 4 mm/min. The oil samples were assessed for their quality parameters and spectra curves within the wavelength range of 325-600 nm. The results show that heating temperatures in the range of 40 °C to 80 °C increased the oil output; however, a maximum oil yield of 48.869 ± 6.023% with a minimum energy of 533.709 ± 65.644 J at the fifth repeated pressing was obtained from the unheated sample compared to the heated samples. The peroxide values ranged from 6.898 ± 0.144 to 7.290 ± 0.507 meq O2/kg, acid values from 1.043 ± 0.166 to 1.998 ± 0.276 mg KOH/g oil and free fatty acid values from 0.521 ± 0.083 to 0.999 ± 0.138 mg KOH/g oil, which were within the recommended quality threshold. There were significant spectral differences among the oil samples. A single absorbance peak was observed at 350 nm for all oil samples, indicating low levels of pigment molecules in the oil. The study revealed the need for repeated pressings to recover the considerable residual oil remaining in the seedcake after the first pressing.

Briquetting of sugarcane bagasse as a proper waste management technology in Vietnam.

The present research describes an application of high-pressure briquetting technology to the waste management of sugarcane processing in Vietnam. The amount of generated sugarcane bagasse was monitored during sugarcane processing within the street juice production in Hue city, Vietnam. Generated sugarcane bagasse was subjected to fuel parameters analysis within its suitability for direct combustion. The obtained sugarcane bagasse was converted into bio-briquette fuel by a high-pressure briquetting press and its mechanical quality was determined. Results proved that the proportion of generated sugarcane bagasse from whole sugarcane stem mass was equal to 35.45%. This indicated generation of an abundant amount of sugarcane bagasse worldwide in general. Fuel parameters analysis proved high quality level of low ash content = 0.97% and high calorific values (gross calorific value = 18.35 MJ·kg-1, net calorific value = 17.06 MJ·kg-1), which indicated good suitability for direct combustion processes. Indicators of mechanical quality proved the following observations: mechanical durability = 99.29%, compressive strength = 150.82 N∙mm-1 and bulk density = 1022.44 kg·m-3, with all these indicators representing positive results. In general, the observed results indicated suitability of sugarcane bagasse valorization within the production of bio-briquette fuel by using high-pressure briquetting technology. Finally, analysis of such waste biomass proved its great potential for energy recovery, thus, the advantage of its valorization within the sustainable technologies.

The Effect of Infrared Drying on Color, Projected Area, Drying Time, and Total Phenolic Content of Rose (Rose electron) Petals.

The effects of different drying temperatures (50, 60, 70 °C) on the quality of rose (Rose electron) petals were evaluated in this study. Drying time decreased from 1680 s to 600 s with increased infrared temperature. The temperature and time were increased from 50 °C to 70 °C and 30 min to 60 min, respectively, and a decrease in the fruit color quality was observed. The projected area (PA) of rose petals was affected significantly from temperature. After the drying process, the largest PA was observed as 33.35 cm2 (50 °C, 30 min), while the smallest achieved at 70 °C, 60 min (27.96 cm2). Depending on the temperature values (50, 60, 70 °C), the average projection area of dry samples of the rose petals decreased 2.17 times compared to the projection area of fresh samples. The dried samples demonstrated an increase in the total phenolic (TP) content compared to the fresh samples. The maximum TP (44.49 mg GAE/g) was achieved at 45 min and 70 °C rose petals sample. The results concluded that infrared drying for 45 min at 70 °C could be recommended for drying rose (rosa electron) petals.

Evaluation of physical properties of rice used in traditional Kyrgyz Cuisine.

Eight staple rice cultivars consumed in Kyrgyzstan were evaluated for physical properties in this study. The dimensions of investigated grains correspond to 5.29-6.99 mm for length, 2.52-3.10 mm for width, and 1.88-2.13 for thickness. Equivalent diameter was in range of 3.14 - 3.47 mm, surface area took 25.35-31.90 mm². The sphericity analysis values varied from 0.480 to 0.559, aspect ratio from 0.39 to 0.55, volume of the grain was measured in range from 16.25 to 22.02 mm3, bulk density values were 0.77-0.87 g/cm3, and solid density from 1.17 to 1.41 g/cm3. The porosity of grain was equal to 28.27-39.83%, thousand kernel weight correspond to 19.67 to 27.15 g, rupture force of grain was measured in range of 63.47-155.50 N, color characteristic varied in parameters L*, a* and b*, 37.58-72.19, -0.22-10.17, and 9.65-21.12, respectively. Optimum cooking time ranged from 19.33 to 33.00 min. The water uptake ratios for 30 min of soaking were 1.21-1.28, 1.18-1.45, and 1.14-1.57 for 30, 45, and 60°C, respectively. While the water uptake ratios for 60 min of soaking were 1.22-1.42, 1.19-1.54, and 1.25-1.75 for 30, 45, and 60°C, respectively. Optimal cooking time showed that imported varieties needed lower interval for full grain cooking compared to the local Kyrgyz varieties. It was found that Kyrgyz rice varieties staying more firm after cooking as compared to imported varieties and therefore more suitable for the local traditional dish such as plov.