Your browser doesn't support javascript.
loading
Mostrar: 20 | 50 | 100
Resultados 1 - 11 de 11
Filtrar
Mais filtros










Base de dados
Intervalo de ano de publicação
1.
ACS Sustain Resour Manag ; 1(3): 417-426, 2024 Mar 28.
Artigo em Inglês | MEDLINE | ID: mdl-38566747

RESUMO

While perovskite photovoltaic (PV) devices are on the verge of commercialization, promising methods to recycle or remanufacture fully encapsulated perovskite solar cells (PSCs) and modules are still missing. Through a detailed life-cycle assessment shown in this work, we identify that the majority of the greenhouse gas emissions can be reduced by re-using the glass substrate and parts of the PV cells. Based on these analytical findings, we develop a novel thermally assisted mechanochemical approach to remove the encapsulants, the electrode, and the perovskite absorber, allowing reuse of most of the device constituents for remanufacturing PSCs, which recovered nearly 90% of their initial performance. Notably, this is the first experimental demonstration of remanufacturing PSCs with an encapsulant and an edge-seal, which are necessary for commercial perovskite solar modules. This approach distinguishes itself from the "traditional" recycling methods previously demonstrated in perovskite literature by allowing direct reuse of bulk materials with high environmental impact. Thus, such a remanufacturing strategy becomes even more favorable than recycling, and it allows us to save up to 33% of the module's global warming potential. Remarkably, this process most likely can be universally applied to other PSC architectures, particularly n-i-p-based architectures that rely on inorganic metal oxide layers deposited on glass substrates. Finally, we demonstrate that the CO2-footprint of these remanufactured devices can become less than 30 g/kWh, which is the value for state-of-the-art c-Si PV modules, and can even reach 15 g/kWh assuming a similar lifetime.

2.
Nat Energy ; 9(2): 172-183, 2024.
Artigo em Inglês | MEDLINE | ID: mdl-38419691

RESUMO

The stabilization of grain boundaries and surfaces of the perovskite layer is critical to extend the durability of perovskite solar cells. Here we introduced a sulfonium-based molecule, dimethylphenethylsulfonium iodide (DMPESI), for the post-deposition treatment of formamidinium lead iodide perovskite films. The treated films show improved stability upon light soaking and remains in the black α phase after two years ageing under ambient condition without encapsulation. The DMPESI-treated perovskite solar cells show less than 1% performance loss after more than 4,500 h at maximum power point tracking, yielding a theoretical T80 of over nine years under continuous 1-sun illumination. The solar cells also display less than 5% power conversion efficiency drops under various ageing conditions, including 100 thermal cycles between 25 °C and 85 °C and an 1,050-h damp heat test.

3.
Nanoscale ; 15(7): 3130-3134, 2023 Feb 16.
Artigo em Inglês | MEDLINE | ID: mdl-36723028

RESUMO

A sacrificial film of polystyrene nanoparticles was utilized to introduce nano-cavities into mesoporous metal oxide layers. This enabled the growth of larger perovskite crystals inside the oxide scaffold with significantly suppressed non-radiative recombination and improved device performance. This work exemplifies potential applications of such nanoarchitectonic approaches in perovskite opto-electronic devices.

4.
Chem Soc Rev ; 51(17): 7509-7530, 2022 Aug 30.
Artigo em Inglês | MEDLINE | ID: mdl-35929481

RESUMO

Halide perovskite solar cells (PSCs) have achieved power conversion efficiencies (PCEs) approaching 26%, however, the stability issue hinders their commercialization. Due to the soft ionic nature of perovskite materials, the strain effect on perovskite films has been recently recognized as one of the key factors that affects their opto-electronic properties and the device stability. Herein, we summarized the origins of strain, characterization techniques, and implications of strain on both perovskite film and solar cells as well as various strategies to control the strain. Finally, we proposed effective strategies for future strain engineering. We believe this comprehensive review could further facilitate researchers with a deeper understanding of strain effect and enhance the research activity in engineering the strain to further improve performance and especially the device stability toward commercialization.

5.
ACS Energy Lett ; 6(11): 3916-3923, 2021 Nov 12.
Artigo em Inglês | MEDLINE | ID: mdl-34805526

RESUMO

Tremendous efforts have been dedicated toward minimizing the open-circuit voltage deficits on perovskite solar cells (PSCs), and the fill factors are still relatively low. This hinders their further application in large scalable modules. Herein, we employ a newly designed ammonium salt, cyclohexylethylammonium iodide (CEAI), for interfacial engineering between the perovskite and hole-transporting layer (HTL), which enhanced the fill factor to 82.6% and consequent PCE of 23.57% on the target device. This can be associated with a reduction of the trap-assisted recombination rate at the 3D perovskite surface, via formation of a 2D perovskite interlayer. Remarkably, the property of the 2D perovskite interlayer along with the cyclohexylethyl group introduced by CEAI treatment also determines a pronounced enhancement in the surface hydrophobicity, leading to an outstanding stability of over 96% remaining efficiency of the passivated devices under maximum power point tracking with one sun illumination under N2 atmosphere at room temperature after 1500 h.

6.
ACS Appl Nano Mater ; 3(3): 2463-2471, 2020 Mar 27.
Artigo em Inglês | MEDLINE | ID: mdl-32270136

RESUMO

The electrically insulating space layer takes a fundamental role in monolithic carbon-graphite based perovskite solar cells (PSCs) and it has been established to prevent the charge recombination of electrons at the mp-TiO2/carbon-graphite (CG) interface. Thick 1 µm printed layers are commonly used for this purpose in the established triple-mesoscopic structures to avoid ohmic shunts and to achieve a high open circuit voltage. In this work, we have developed a reproducible large-area procedure to replace this thick space layer with an ultra-thin dense 40 nm sputtered Al2O3 which acts as a highly electrically insulating layer preventing ohmic shunts. Herewith, transport limitations related so far to the hole diffusion path length inside the thick mesoporous space layer have been omitted by concept. This will pave the way toward the development of next generation double-mesoscopic carbon-graphite-based PSCs with highest efficiencies. Scanning electron microscope, energy dispersive X-ray analysis, and atomic force microscopy measurements show the presence of a fully oxidized sputtered Al2O3 layer forming a pseudo-porous covering of the underlying mesoporous layer. The thickness has been finely tuned to achieve both electrical isolation and optimal infiltration of the perovskite solution allowing full percolation and crystallization. Photo voltage decay, light-dependent, and time-dependent photoluminescence measurements showed that the optimal 40 nm thick Al2O3 not only prevents ohmic shunts but also efficiently reduces the charge recombination at the mp-TiO2/CG interface and, at the same time, allows efficient hole diffusion through the perovskite crystals embedded in its pseudo-pores. Thus, a stable V OC of 1 V using CH3NH3PbI3 perovskite has been achieved under full sun AM 1.5 G with a stabilized device performance of 12.1%.

7.
Sci Rep ; 7(1): 14899, 2017 11 02.
Artigo em Inglês | MEDLINE | ID: mdl-29097712

RESUMO

Relating crystallization of the absorber layer in a perovskite solar cell (PSC) to the device performance is a key challenge for the process development and in-depth understanding of these types of high efficient solar cells. A novel approach that enables real-time photo-physical and electrical characterization using a graphite-based PSC is introduced in this work. In our graphite-based PSC, the device architecture of porous monolithic contact layers creates the possibility to perform photovoltaic measurements while the perovskite crystallizes within this scaffold. The kinetics of crystallization in a solution based 2-step formation process has been analyzed by real-time measurement of the external photon to electron quantum efficiency as well as the photoluminescence emission spectra of the solar cell. With this method it was in particular possible to identify a previously overlooked crystallization stage during the formation of the perovskite absorber layer. This stage has significant influence on the development of the photocurrent, which is attributed to the formation of electrical pathways between the electron and hole contact, enabling efficient charge carrier extraction. We observe that in contrast to previously suggested models, the perovskite layer formation is indeed not complete with the end of crystal growth.

8.
ACS Appl Mater Interfaces ; 9(36): 30567-30574, 2017 Sep 13.
Artigo em Inglês | MEDLINE | ID: mdl-28834429

RESUMO

The most efficient organic-inorganic perovskite solar cells (PSCs) contain the conventional n-i-p mesoscopic device architecture using a semiconducting TiO2 scaffold combined with a compact TiO2 blocking layer for selective electron transport. These devices achieve high power conversion efficiencies (15-22%) but mainly require high-temperature sintering (>450 °C), which is not possible for temperature-sensitive substrates. Thus far, comparably little effort has been spent on alternative low-temperature (<150 °C) routes to realize high-efficiency TiO2-based PSCs; instead, other device architectures have been promoted for low-temperature processing. In this paper the compatibility of the conventional mesoscopic TiO2 device architecture with low-temperature processing is presented for the first time with the combination of electron beam evaporation for the compact TiO2 and UV treatment for the mesoporous TiO2 layer. Vacuum evaporation is introduced as an excellent deposition technique of uniform compact TiO2 layers, adapting smoothly to the rough fluorine-doped tin oxide substrate surface. Effective removal of organic binders by UV light is shown for the mesoporous scaffold. Entirely low-temperature-processed PSCs with TiO2 scaffold reach encouraging stabilized efficiencies of up to 18.2%. This process fulfills all requirements for monolithic tandem devices with high-efficiency silicon heterojunction solar cells as the bottom cell.

9.
Chemphyschem ; 15(6): 1076-87, 2014 Apr 14.
Artigo em Inglês | MEDLINE | ID: mdl-24599537

RESUMO

Recently, the first commercial dye solar cell (DSC) products based on the mesoscopic principle were successfully launched. Introduction to the market has been accompanied by a strong increase in patent applications in the field during the last four years, which is a good indication of further commercialization activity. Materials and cell concepts have been developed to such extent that easy uptake by industrial manufacturers is possible. The critical phase for broad market acceptance has therefore been reached, which implies focusing on standardization-related research topics. In parallel the number of scientific publications on DSC is growing further (>3500 since 2012), and the range of new or renewed fundamental topics is broadening. A recent example is the introduction of the perovskite mesoscopic cell, for which an efficiency of 14.1% has been certified. Thus, a growing divergence between market introduction and research could be the consequence. Herein, an attempt is made to show that such an unwanted divergence can be prevented, for example, by developing suitable reference-type cell and module concepts as well as manufacturing routes. An in situ cell manufacturing concept that can be applied to mesoscopic-based solar cells in a broader sense is proposed. As a guideline for future module concepts, recent results for large-area, glass-frit-sealed DSC modules from efficiency studies (6.6% active-area efficiency) and outdoor analysis are discussed. Electroluminescence measurements are introduced as a quality tool. Another important point that is addressed is sustainability, which affects both market introduction and the direction of fundamental research.

10.
Chemphyschem ; 9(5): 793-8, 2008 Apr 04.
Artigo em Inglês | MEDLINE | ID: mdl-18338345

RESUMO

A new, extremely simple concept for the use of energy transfer as a means to the enhancement of light absorption and current generation in the dye solar cell (DSC) is presented. This model study is based upon a carboxy-functionalized 4-aminonaphthalimide dye (carboxy-fluorol) as donor, and (NBu4)2[Ru(dcbpy)2(NCS)2] (N719) as acceptor chromophores. A set of three different devices is assembled containing either exclusively carboxy-fluorol or N719, or a mixture of both. This set of transparent devices is characterized via IV-measurements under AM1.5G and monochromatic illumination and their light-harvesting and external quantum efficiencies (LHE and EQE, respectively) are determined as well. It is shown that the device containing only the donor chromophore has a marginal power conversion efficiency, thus indicating that carboxy-fluorol is a poor sensitizer for the DSC. Cyclovoltametric measurements show that the poor sensitization ability arises from the kinetic inhibition of electron injection into the TiO2 conduction band. Comparing the spectral properties of the DSCs assembled presently, however, demonstrates that light absorbed by carboxy-fluorol is almost quantitatively contributing to the photocurrent if N719 is present as an additional sensitizer. In this case, N719 acts as a catalyst for the sensitization of TiO2 by carboxy-fluorol in addition to being a photosensitizer. Evaluation of the maximum output power under blue illumination shows that the introduction of an energy-donor moiety via coadsorption, leads to a significant increase in the monochromatic maximum output power. This result demonstrates that energy transfer between coadsorbed chromophores could be useful for the generation of current in dye-sensitized solar cells.


Assuntos
Corantes , Elétrons , Transferência Ressonante de Energia de Fluorescência , Energia Solar , Adsorção , Cinética , Fotoquímica , Semicondutores , Titânio
11.
Chemphyschem ; 8(10): 1548-56, 2007 Jul 16.
Artigo em Inglês | MEDLINE | ID: mdl-17546710

RESUMO

A new bichromophoric dyad based on an alkyl-functionalized aminonaphthalimide as energy-donor chromophore and [Ru(dcbpy)2(acac)]Cl (dcbpy=4,4'-dicarboxybipyridine, acac=acetylacetonato) as energy acceptor and sensitizing chromophore is synthesized. Efficient quenching of the donor-chromophore emission is observed in solution, presumably due to resonant energy transfer. This dyad is then used as a sensitizer in a dye solar cell. By comparing the spectral properties of transparent dye solar cells sensitized with the dyad and [Ru(dcbpy)2(acac)]Cl, it is possible to demonstrate that photons absorbed by the donor moiety also contribute significantly to the generation of current. Instead of using acceptor luminescence as a probe, enhanced photocurrent generation is employed to estimate the energy-transfer efficiency. Fitting theoretical to experimental external quantum efficiency functions gives a value for the energy-transfer efficiency of 85 %. Evaluation of the maximum output power of dye solar cells sensitized with the dyad and [Ru(dcbpy)2(acac)]Cl showed, under selective illumination at the absorption maximum of the donor chromophore, that the introduction of the energy-donor moiety leads to a significant increase in the monochromatic maximum output power under blue illumination. This result demonstrates the usefulness of energy transfer for the generation of current in dye-sensitized solar cells.

SELEÇÃO DE REFERÊNCIAS
DETALHE DA PESQUISA
...