Inclination of the occlusal plane is associated with the direction of the masticatory movement path.

Using lateral cephalograms and a jaw movement-recording system, the relationship between the masticatory movement path and dentofacial morphology was investigated in 17 subjects (9 males and 8 females, mean age 23.5 years) without a history of orthodontic treatment. The masticatory movement path was measured at the right and left lower first molar while the subjects chewed gum. The angle between the Frankfort horizontal plane and the masticatory axis (FH-masticatory angle), defined as the axis passing the opening and closing turning point on the sagittal masticatory path, was also measured. The correlation between the angular measurements derived from the lateral cephalogram and the FH-masticatory angle was then investigated. A positive correlation was observed in the FH-masticatory, occlusal plane (P < 0.05), and mandibular plane (P < 0.01) angles. Furthermore, it was found that the angle between the masticatory axis and the occlusal plane (69.1 +/- 4.2 degrees) remained constant even as the masticatory axis showed a tendency to incline forward as the mandibular plane angle became steeper; the rates of change of the FH-masticatory and the occlusal plane angles were approximately 1:1. This finding suggests that the masticatory movement path is closely associated with the occlusal plane.

Effects of root morphology on stress distribution at the root apex.

It is thought that the stress concentration at the root apex caused by orthodontic force induces root resorption. The purpose of this study was to investigate stress distribution at the root in cases of deviated root shapes using finite element models (FEMs). To clarify this, five three-dimensional FEMs divided by deviated root shape (normal, short, blunt, bent root apex, pipette shape) were constructed and, experimental orthodontic forces, applied in a vertical (intrusive) and horizontal (lingual) direction to the tooth axis. In the short-root model, significant stress was concentrated at the middle of the root. The blunt-shaped root model showed no significant stress concentration at the root. In the models with a bent or pipette-shaped root, significant stress was concentrated at the root apex. During orthodontic force application, stress concentration was observed in the root of the models with short, bent, and pipette-shaped roots, indicating that attention must be paid to root shape during orthodontic treatment.

Recommended placement torque when tightening an orthodontic mini-implant.

To determine an adequate placement torque for obtaining a better success rate of mini-implants that are screwed into the buccal alveolar bone of the posterior region as an anchor for orthodontic treatment, implant placement torque (IPT) was measured. The subjects were 41 orthodontic patients (124 implants), with an average age of 24.9 years (SD 6.5 years), who had surgery to place titanium mini-implants. The peak value of IPT was measured using a torque screwdriver. The success rate of the mini-implant anchor for 124 implants was 85.5%. The mean IPT ranged from 7.2 to 13.5 N cm, depending on the location of the implants. There was a significant difference in the IPT between maxilla and mandible. The IPT in the mandible was, unexpectedly, significantly higher in the failure group than in the success group. Therefore, a large IPT should not be used always. According to our calculations of the risk ratio for failure, to raise the success rate of 1.6-mm diameter mini-implants, the recommended IPT is within the range from 5 to 10 N cm.

Stresses in mandibular cortical bone during mastication: biomechanical considerations using a three-dimensional finite element method.

This study investigated biomechanical aspects of the action of the biting force during mastication upon the mandibular bone in the lower first molar area. A three-dimensional (3D) finite element model (FEM) consisting of the tooth, periodontal ligament (PDL), alveolar bone, and cortical bone corresponding to the lower first molar area based on computed tomogram (CT) images was constructed. The model was then analyzed while applying a biting force during mastication, which was transmitted from the tooth to the cortical bone, through the PDL and cancellous bone. A compressive stress of 0.3-7.9 MPa acted on the cortical bone during mastication. In the model, the stress in the cortical bone was distributed from the linguo-superior margin to the basal area, and was also observed in the bucco-medial area. These areas completely agreed with the areas that were significantly thicker in the morphological study described by Masumoto et al. (10). It is suggested that there may be a relationship between masticatory force and cortical bone hypertrophy. Further study of the effects of various factors is required.

An experimental study on mandibular expansion: increases in arch width and perimeter.

The purpose of this study was to estimate the increase in arch perimeter associated with mandibular lateral expansion. The mandibular expansion was simulated using a three-dimensional (3D) finite element method (FEM) and a computer graphics technique (3D simulation). The centre of rotation of molars during movement accompanied by lateral expansion was calculated using 3D FEM. The geometry of the model was determined using the mandibular bone of an East Indian skeletal specimen and 1 mm computer tomogram (CT) slices. The 3D set-up simulation was then conducted using 3D computer graphics instead of performing a manual set-up. Rotational movement was induced in the buccal segment, from the first premolar to second molar, in the 3D set-up model around the location of the centre of rotation (4.5 mm below the root apex of the first molar) derived from the FEM. According to 3D simulation, the model showed an opening space of 1.43 mm between the canine and first premolar, and thus a change in arch perimeter of 2.86 mm. The tip of the mesio-lingual cusp of the first molar moved 3.88 mm laterally, resulting in a change in inter-molar width of 7.76 mm. These values mean that a 1 mm increase in arch width resulted in an increase in arch perimeter of 0.37 mm. This result would be of value clinically for prediction of the effects of mandibular expansion.