RESUMO
Mixed tin-lead (Sn-Pb) perovskites have attracted the attention of the community due to their narrow bandgap, ideal for photovoltaic applications, especially tandem solar cells. However, the oxidation and rapid crystallization of Sn2+ and the interfacial traps hinder their development. Here, cross-linkable [6,6]-phenyl-C61-butyric styryl dendron ester (C-PCBSD) is introduced during the quenching step of perovskite thin film processing to suppress the generation of surface defects at the electron transport layer interface and improve the bulk crystallinity. The C-PCBSD has strong coordination ability with Sn2+ and Pb2+ perovskite precursors, which retards the crystallization process, suppresses the oxidation of Sn2+, and improves the perovskite bulk and surface crystallinity, yielding films with reduced nonradiative recombination and enhanced interface charge extraction. Besides, the C-PCBSD network deposited on the perovskite surface displays superior hydrophobicity and oxygen resistance. Consequently, the devices with C-PCBSD obtain PCEs of up to 23.4% and retained 97% of initial efficiency after 2000 h of storage in a N2 atmosphere.
RESUMO
The high-performance Y6-based nonfullerene acceptors (NFAs) feature a C-shaped A-DA'D-A-type molecular architecture with a central electron-deficient thiadiazole (Tz) A' unit. In this work, we designed and synthesized a new A-D-A-type NFA, termed CB16, having a C-shaped ortho-benzodipyrrole-based skeleton of Y6 but with the Tz unit eliminated. When processed with nonhalogenated xylene without using any additives, the binary PM6:CB16 devices display a remarkable power conversion efficiency (PCE) of 18.32% with a high open-circuit voltage (Voc) of 0.92 V, surpassing the performance of the corresponding Y6-based devices. In contrast, similarly synthesized SB16, featuring an S-shaped para-benzodipyrrole-based skeleton, yields a low PCE of 0.15% due to the strong side-chain aggregation of SB16. The C-shaped A-DNBND-A skeleton in CB16 and the Y6-series NFAs constitutes the essential structural foundation for achieving exceptional device performance. The central Tz moiety or other A' units can be employed to finely adjust intermolecular interactions. The single-crystal X-ray structure reveals that ortho-benzodipyrrole-embedded A-DNBND-A plays an important role in the formation of a 3D elliptical network packing for efficient charge transport. Solution structures of the PM6:NFAs detected by small- and wide-angle X-ray scattering (SWAXS) indicate that removing the Tz unit in the C-shaped skeleton could reduce the self-packing of CB16, thereby enhancing the complexing and networking with PM6 in the spin-coating solution and the subsequent device film. Elucidating the structure-property-performance relationships of A-DA'D-A-type NFAs in this work paves the way for the future development of structurally simplified A-D-A-type NFAs.
RESUMO
Alkoxy side chain engineering on the ß-position of the thienothiophene units of Y6 derivatives plays a vital role in improving photovoltaic performances with simultaneously increasing open-circuit voltage (Voc) and fill factor (FF). In this work, we prepared a series of asymmetric non-fullerene acceptors (NFAs) by introducing alkoxy side chains and phenoxy groups on the state-of-the-art Y6-derivative BTP-BO-4F. For the comparison, 2O-BO-4F with a symmetric alkoxy side chain on the outer thiophene units and BTP-PBO-4F with an asymmetric N-attached phenoxy alkyl chain on the pyrrole ring are synthesized from BTP-BO-4F. Thereafter, we construct four asymmetric NFAs by introducing different lengths of linear/branched alkoxy chains on the ß-position of the thienothiophene units of BTP-PBO-4F. The resulting NFAs, named L10-PBO, L12-PBO, B12-PBO, and B16-PBO (L = linear and B = branched alkoxy side chains), are collectively called OR-PBO-series. Unexpectedly, all OR-PBO NFAs exhibit strong edge-on molecular packing and weaker π-π interactions in the film state, which diminish the charge transfer in organic solar cell (OSC) devices. As a consequence, the optimal devices of OR-PBO-based binary blends show poor photovoltaic performances [power conversion efficiency (PCE) = 6.52-9.62%] in comparison with 2O-BO-4F (PCE = 12.42%) and BTP-PBO-4F (PCE = 15.30%) reference blends. Nevertheless, the OR-PBO-based binary devices show a higher Voc and smaller Vloss. Especially, B12-PBO- and B16-PBO-based devices achieve Voc over 1.00 V, which is the highest value of Y-series OSC devices to the best of our knowledge. Therefore, by utilizing higher Voc of OR-PBO binary blends, B12-PBO and B16-PBO are incorporated into the PM6:BTP-PBO-4F-based binary blend and fabricated ternary devices. As a result, the PM6:BTP-PBO-4F:B12-PBO ternary device delivers the best PCE of 15.60% with an increasing Voc and FF concurrently.
RESUMO
Area-selective atomic layer deposition (AS-ALD) has drawn significant attention in the past decade because of the potential applications in bottom-up processing, which enables fabricating nanostructures at the atomic level without multiple patterning and lithographic processing that could easily cause alignment issues. Although AS-ALD has been demonstrated using various self-assembled monolayers (SAMs), it is still challenging to develop wet SAM deposition for AS-ALD that is suitable for industrial and semiconductor processes. In this work, we demonstrate highly effective AS-ALD of Al2O3 on Co/SiO2 patterned wafers using fluorinated thiol in both solution and vapor phase. Compared with conventional SAMs using alky-thiols, the fluorinated-thiol SAMs demonstrate greater blocking ability against ALD precursors owing to excellent hydrophobicity. Furthermore, much shorter deposition times can be achieved in vaporizable fluorinated thiol molecules, improving processing throughput and productivity. Most importantly, the SAM regeneration and redosing processes can further enhance the selectivity of AS-ALD, opening a promising avenue to realize the bottom-up approach in practical semiconductor applications.
RESUMO
Terminal acceptor atoms and side-chain functionalization play a vital role in the construction of efficient nonfullerene small-molecule acceptors (NF-SMAs) for AM1.5G/indoor organic photovoltaic (OPV) applications. In this work, we report three dithienosilicon-bridged carbazole-based (DTSiC) ladder-type (A-DD'D-A) NF-SMAs for AM1.5G/indoor OPVs. First, we synthesize DTSiC-4F and DTSiC-2M, which are composed of a fused DTSiC-based central core with difluorinated 1,1-dicyanomethylene-3-indanone (2F-IC) and methylated IC (M-IC) end groups, respectively. Then, alkoxy chains are introduced in the fused carbazole backbone of DTSiC-4F to form DTSiCODe-4F. From solution to film absorption, DTSiC-4F exhibits a bathochromic shift with strong π-π interactions, which improves the short-circuit current density (Jsc) and the fill factor (FF). On the other hand, DTSiC-2M and DTSiCODe-4F display up-shifting lowest unoccupied molecular orbital (LUMO) energy levels, which enhances the open-circuit voltage (Voc). As a result, under both AM1.5G/indoor conditions, the devices based on PM7:DTSiC-4F, PM7:DTSiC-2M, and PM7:DTSiCOCe-4F show power conversion efficiencies (PCEs) of 13.13/21.80%, 8.62/20.02, and 9.41/20.56%, respectively. Furthermore, the addition of a third component to the active layer of binary devices is also a simple and efficient strategy to achieve higher photovoltaic efficiencies. Therefore, the conjugated polymer donor PTO2 is introduced into the PM7:DTSiC-4F active layer because of the hypsochromically shifted complementary absorption, deep highest occupied molecular orbital (HOMO) energy level, good miscibility with PM7 and DTSiC-4F, and optimal film morphology. The resulting ternary OSC device based on PTO2:PM7:DTSiC-4F can improve exciton generation, phase separation, charge transport, and charge extraction. As a consequence, the PTO2:PM7:DTSiC-4F-based ternary device achieves an outstanding PCE of 13.33/25.70% under AM1.5G/indoor conditions. As far as we know, the obtained PCE results under indoor conditions are one of the best binary/ternary-based systems processed from eco-friendly solvents.
RESUMO
To investigate the relationship between molecular structures and spontaneous orientation polarization (SOP) in organic thin films, 2,5,8-tris(1-phenyl-1H-benzo[d]imidazol-2-yl)benzo[1,2-b:3,4-b':5,6-bâ³] trithiophene (TPBTT) and its ethyl derivative (m-ethyl-TPBTT) were synthesized. Variable angle spectroscopic ellipsometry and two-dimensional grazing-incidence wide-angle X-ray scattering showed that the vacuum-deposited films of TPBTT and m-ethyl-TPBTT had a higher degree of molecular orientation parallel to the substrate compared with that of prototypical 2,2',2â³-(1,3,5-benzinetriyl)-tris(1-phenyl-1-H-benzimidazole) (TPBi) due to the larger π-conjugated benzotrithiophene core. However, TPBTT films showed a lower SOP of +54.4 mV/nm than did the TPBi film (+77.3 mV/nm), indicating that the molecular orientation alone did not determine the SOP. In contrast, m-ethyl-TPBTT showed a larger SOP of +104.0 mV/nm in the film. Quantum chemical calculations based on density functional theory suggested that the differences in the stable molecular conformation and the permanent dipole moments between TPBTT and m-ethyl-TPBTT caused the differences in SOP. These results suggest that the simultaneous control of the orientational order and conformation of the molecules is important to achieving a large SOP in films.
RESUMO
Developing new electron transport layers has been an effective way to fabricate high-performance bulk-heterojunction organic solar cells (OSCs). Resolving the longstanding problems associated with commonly used zinc oxide (ZnO), such as electron traps and light-induced device deterioration, however, is still a great challenge. In this study, glycerol diglycidyl ether (GDE) and 1,4-butanesultone (BS) are blended with polyethyleneimine (PEI) to produce cross-linkable PEI-based materials, PEI-GDE and PEI-GDE-BS, which can function as alternative electron transport layers to replace conventional ZnO cathode-modifying layers in inverted OSCs. PEI-GDE and PEI-GDE-BS are amendable to low-temperature annealing processes to produce cross-linked films. The inverted device structure of ITO/ETL/PM6:BTP-BO-4F:PC71BM/MoO3/Ag was used to evaluate the effects of incorporating PEI-GDE and PEI-GDE-BS as electron transport materials. Compared with ZnO-based devices, the PEI-GDE- and PEI-GDE-BS-based devices exhibit significant improvements in photovoltaic performances due to smoother surface roughness, higher charge collection and exciton dissociation efficiencies, higher electron mobilities, and stronger π-π interactions. In particular, a PEI-GDE-BS-based device shows an outstanding power conversion efficiency (PCE) of 17.55% with a VOC of 0.83 V, a JSC of 27.88 mA/cm2, and an FF of 75.96%, which offers great possibilities in the applications of flexible solar cells.
RESUMO
Molecular backbone modification, alkyl-chain engineering, and end-group functionalization are promising strategies for developing efficient high-performance non-fullerene acceptors (NFAs). Herein, two new NFAs, named TPQ-eC7-4F and TPQ-eC7-4Cl, are designed and synthesized. Both molecules have linear octyl chains on fused quinoxaline-containing heterocyclics as the central backbone and difluorinated (2F)/dichlorinated (2Cl) 1,1-dicyanomethylene-3-indanone (IC) as the end-group units. The influences of alkyl-chains on fused quinoxaline backbone and different halogenated end-groups on optical, electrochemical, and photovoltaic performances of organic solar cells (OSCs) are studied. In comparison with TPQ-eC7-4Cl, TPQ-eC7-4F exhibits blue-shifted absorptions with higher molar extinction coefficients in the film state as well as in the donor/acceptor (D/A) blend film state and up-shifting lowest unoccupied molecular orbital (LUMO) energy level. As a result, the OSC devices based on the PBDB-T:TPQ-eC7-4F display an outstanding power conversion efficiency (PCE) of 15.83% with a simultaneously increased open-circuit voltage (Voc) of 0.85 V, a short-circuit current-density (Jsc) of 25.89 mA cm-2, and a fill factor (FF) of 72.20%, whereas the PBDB-T:TPQ-eC7-4Cl-based OSC device shows a decent PCE of 14.48% with a Voc of 0.84 V, a Jsc of 24.56 mA/cm2, and an FF of 69.77%. To the best of our knowledge, this is the highest photovoltaic performance of PBDB-T-based single-junction binary-OSCs. In comparison, ascribed to the high crystallinity and low solubility of BTP-eC7-4Cl, the corresponding PBDB-T:BTP-eC7-4Cl-based OSC device shows poor photovoltaic performance (PCE of 11.87%). The experimental results demonstrate that fine-tuning the fused quinoxaline backbone with alkyl-chain and end-group functionalization are promising strategies to construct high-performance NFAs for PBDB-T-based single-junction binary-OSCs.
RESUMO
The molecular design of wide-bandgap conjugated polymer donors (WB-CPDs) is a promising strategy for tuning the bulk heterojunction blend film morphologies to achieve high-performance organic photovoltaic (OPV) devices. Herein, we synthesize two WB-CPDs, namely, PBQ-H and PBQ-M, with and without methyl groups on the fused-dithieno[3,2-f:2',3'-h]quinoxaline (DTQx) moiety. We systematically investigate their structure-property relationship and OPV performances. The AFM and 2D grazing-incidence wide-angle X-ray scattering (GIWAXS) studies reveal that the PBQ-H:BO-4Cl BHJ blend shows strengthened aggregation behavior and stronger π-π stacking on face-on orientation compared with the PBQ-M:BO-4Cl BHJ blend, enhancing the phase separation, charge transport, and fill factor (FF). Blend film absorption spectra, however, show that the PBQ-H:BO-4Cl BHJ blend exhibits a lower absorption coefficient than that of the PBQ-M:BO-4Cl BHJ blend, which decreases the short-circuit current density (JSC). As a consequence, the optimized PBQ-H:BO-4Cl BHJ blend delivers a higher power conversion efficiency (PCE) of 12.88% with a JSC of 23.97 mA/cm2, an open-circuit voltage (VOC) of 0.86 V, and an FF of 62.46%, compared with the PBQ-M:BO-4Cl BHJ blend (PCE of 11.81% with a JSC of 24.78 mA/cm2, a VOC of 0.85 V, and an FF of 56.11%). Overall, this work demonstrates that alkyl group substitution on the DTQx moiety on the basis of WB-CPDs is critical for controlling the film morphology and thus obtaining high OPV performances.
RESUMO
Three isomeric derivatives of 2,2',2â³-(1,3,5-benzinetriyl)-tris(1-phenyl-1-H-benzimidazole) (TPBi) bearing ethyl groups on the N-phenyl moieties were synthesized to elucidate the effects of intramolecular interactions on spontaneous orientation polarization (SOP) in thin films. The films of the TPBi derivatives displayed enhanced SOP with a surface potential change of up to 1.8 times that for TPBi, and the p-substituted derivative exhibited the largest potential change reported to date (+141.0 mV/nm). Density functional theory calculations and single-crystal structure analysis suggest that the introduction of the ethyl groups switched the stable molecular conformation from C1 to C3 symmetry. Through analysis of the structural anisotropy in the films by spectral ellipsometry and two-dimensional (2D) grazing-incidence wide-angle X-ray scattering, we conclude that the conformational change of the molecules was the major factor underlying the SOP enhancement.
RESUMO
Power conversion efficiencies (PCEs) and device stability are two key technical factors restricting the commercialization of organic solar cells (OSCs). In the past decades, though the PCEs of OSCs have been significantly enhanced, device instability, especially in the state-of-the-art nonfullerene system, still needs to be solved. In this work, an effective crosslinker (namely, DTODF-4F), with conjugated fluorene-based backbone and crosslinkable epoxy side-chains, has been designed and synthesized, which is introduced to enhance the morphological stabilization of the PM6:Y6-based film. This crosslinker with two epoxy groups can be in situ crosslinked into a stable network structure under ultraviolet radiation. We demonstrate that DTODF-4F, which acted as a third component, can promote the exciton dissociation rate and reduce traps/defects, finally resulting in the enhancement of efficiency. In particular, the OSC devices exhibit better stability under continuous heating owing to the morphology fixation of the bulk heterojunction. This work drives the development direction of morphological stabilization to further improve the performance and stability of OSCs.
RESUMO
In this work, two asymmetric non-fullerene acceptors (NFAs), BTP-EHBO-4F and BTP-PHD-4F, are designed to be applied in green-solvent-processable organic photovoltaics (OPVs). BTP-EHBO-4F and BTP-PHD-4F show good solubilities in green solvent o-xylene. As a result, PM6:BTP-EHBO-4F-based devices exhibit outstanding photovoltaic performances using o-xylene as a solvent. By comparison, due to the poor solubility of Y6 in o-xylene, PM6:Y6-based devices show poor performances. Owing to the favorable phase separation, molecule packing, and orientation observed from atomic force microscopy (AFM) and grazing-incidence wide-angle X-ray scattering (GIWAXS) measurements, PM6:BTP-PHD-4F-based devices demonstrate a PCE of 15.91% with a VOC of 0.87 V, a JSC of 25.64 mA/cm2, and an FF of 71.34%. Moreover, PM6:BTP-EHBO-4F-based devices exhibit an impressive PCE of 16.82% with a VOC of 0.85 V, a JSC of 26.12 mA/cm2, and an FF of 75.78%, which is outstanding for OPVs using o-xylene as a solvent.
RESUMO
Improving power conversion efficiencies (PCEs) and stability are two main tasks for organic photovoltaic (OPV) cells. In the past few years, although the PCE of the OPV cells has been considerably improved, the research on device stability is limited. Herein, a cross-linkable material, cross-linked [6,6]-phenyl-C61-butyric styryl dendron ester (c-PCBSD), is applied as an interfacial modification layer on the surface of zinc oxide and as the third component into the PBDB-TF:Y6-based OPV cells to enhance photovoltaic performance and long-term stability. The PCE of the OPV cells that underwent the two-step modification increased from 15.1 to 16.1%. In particular, such OPV cells exhibited much better stability under both thermal and air conditions because of the decreased number of interfacial defects and stable interfacial and active layer morphologies. The results demonstrated that the introduction of a cross-linkable fullerene derivative into the interfacial and active layers is a feasible method to improve the PCE and stability of OPV cells.
RESUMO
In this work, two DTSiC-based nonfullerene acceptors (NFAs), (2,2'-((2Z,2'Z)-((12-(heptadecan-9-yl)-4,4,7,7-tetraoctyl-7,12-dihydro-4H-thieno[2',3':4,5]silolo[3,2-b]thieno[2',3':4,5]silolo[2,3-h]carbazole-2,9-diyl)bis(methaneylylidene))bis(3-oxo-2,3-dihydro-1H-indene-2,1-diylidene))dimalononitrile) (DTSiC-IC) and (2,2'-((5Z,5'Z)-((12-(heptadecan-9-yl)-4,4,7,7-tetraoctyl-7,12-dihydro-4H-thieno[2',3':4,5]silolo[3,2-b]thieno[2',3':4,5]silolo[2,3-h]carbazole-2,9-diyl)bis(methaneylylidene))bis(6-oxo-5,6-dihydro-4H-cyclopenta[c]thiophene-5,4-diylidene))dimalononitrile) (DTSiC-TC), are designed with various end groups (IC and TC). To explore the effect of end-group modifications, photovoltaic performance under AM 1.5G and indoor conditions are comprehensively studied. Compared with DTSiC-IC, DTSiC-TC manifests red-shifted and stronger absorption, downshifted lowest unoccupied molecular orbital (LUMO), and pronounced face-on packing characteristics. As we envisaged, the PM7:DTSiC-TC-based devices outperform the PM7:DTSiC-IC-based devices in both AM 1.5G and indoor (light-emitting diode (LED) 3000 K 1000 lux) conditions with overall higher JSC, FF, and power conversion efficiency (PCE). Furthermore, the PM7:DTSiC-TC-based devices achieve an outstanding PCE of 20.73% with a VOC of 0.87 V, a JSC of 0.095 mA/cm2, and an FF of 70.86%.
RESUMO
Open-surface microfluidics is promising in terms of enabling economical and rapid biochemical analysis for addressing challenges associated with medical diagnosis and food safety. To this end, we present a simple and economical approach to develop an open-surface microfluidic platform suitable for facile liquid transport and mixing. Customizable patterns with tailored wettability are deposited using a plasma-assisted deposition technique under atmospheric pressure. The flow of the dispensed liquid is driven by gravity, and the tilting angle of the device determines the extent of mixing. First, a hexamethyldisiloxane film was deposited to create hydrophobic patterns on glass, and then, hydrophilic acrylic acid was deposited by a patterned cardboard mask to construct a channel suitable for forming channels to transport aqueous liquids without the need of an external energy input; the liquid can be confined to designated pathways. Several designs including Y-junctions, serpentine-shaped patterns, splitting channels, and concentration gradient generation patterns are presented. The proposed method can spatially pattern a surface with a hydrophobic/hydrophilic area, which can function as a microfluidic channel, and the surface can be applied in microfluidic devices with other types of substrates.
RESUMO
In this article, a fluorinated heptacyclic dithienocyclopentacarbazole (DTC)-based non-fullerene acceptor (NFA), DTC(4Ph)-4FIC, is synthesized and blended with J71, PBDB-T, and PBDB-TF, featuring complementary absorption and well-matched energy levels. The DTC(4Ph)-4FIC neat film exhibits face-on preference, whereas the nonfluorinated counterpart, DTC(4Ph)-IC, exhibits edge-on preference; this unique feature owing to fluorination in DTC-based NFAs is observed for the first time. More importantly, DTC(4Ph)-4FIC exhibits improved power conversion efficiencies (PCEs) of 10.92 and 10.41% in J71- and PBDB-T-containing devices, while the devices that employed DTC(4Ph)-IC afford PCEs of 7.76 and 9.48%, respectively. Because PBDB-TF is known to exhibit lower energy levels than J71 and PBDB-T, the corresponding device affords a VOC of 0.95 V, a JSC of 18.29 mA cm-2, a FF of 75.70%, and a PCE of 13.15%, which is 20 and 26% higher than J71- and PBDB-T-containing devices. Furthermore, the inverted device containing the PBDB-TF:DTC(4Ph)-4FIC blend is fabricated using cross-linkable fullerene (C-PCBSD) as the cathode interlayer, affording a decent PCE of 13.36%, with a VOC of 0.94 V, a JSC of 20.20 mA cm-2, and a FF of 70.42%.
RESUMO
Benzene-based 1,1-dicyanomethylene-3-indanone (IC) derivatives have been widely utilized as the end-group to construct acceptor-donor-acceptor type nonfullerene acceptors (A-D-A type NFAs). The extension of the end-group conjugation of nonfullerene acceptors (NFAs) is a rational strategy to facilitate intermolecular stacking of the end-groups which are responsible for efficient electron transportation. A bicyclic benzothiophene-based end-group acceptor, 2-(3-oxo-2,3-dihydro-1H-benzo[b]cyclopenta[d]thiophen-1-ylidene)malononitrile, denoted as α-BC was designed and synthesized. The Knoevenagel condensation of the unsymmetrical 1,3-diketo-precursor with one equivalent of malononitrile selectively reacts with the keto group attached at the α-position of the thiophene unit, leading to the isomerically pure benzothiophene-fused α-BC. The well-defined α-BC with extended conjugation was condensed with three different ladder-type diformylated donors to form three new A-D-A NFAs named BDCPDT-BC, DTCC-BC, and ITBC, respectively. The corresponding IC-based BDCPDT-IC, DTCC-IC, and ITIC model compounds were also synthesized for comparison. The incorporation of the electron-rich benzothiophene unit in the end-group upshifts the lowest unoccupied molecular orbital energy levels of the NFAs, which beneficially enlarges the Voc values. On the other hand, the benzothiophene unit in α-BC not also imparts an optical transition in the shorter wavelengths around 340-400 nm for a better light harvesting ability but also promotes the antiparallel π-π stacking of the end-groups for efficient electron transport. The organic photovoltaic cell devices using a PBDB-T polymer and BC-based NFAs all showed the improved Voc and Jsc values. The BDCPDT-BC- and DTCC-BC-based devices exhibited a power conversion efficiency (PCE) of 10.82 and 10.74%, respectively, which outperformed the corresponding BDCPDT-IC-, and DTCC-IC-based devices (9.33 and 9.25%). More importantly, the ITBC-based device delivered the highest PCE of 12.07% with a Jsc of 19.90 mA/cm2, a Voc of 0.94 V, and an fill factor of 64.51%, representing a 14% improvement relative to the traditional ITIC-based device (10.05%).
RESUMO
Halide perovskite films processed from solution at low-temperature offer promising opportunities to make flexible solar cells. However, the brittleness of perovskite films is an issue for mechanical stability in flexible devices. Herein, photo-crosslinked [6,6]-phenylC61 -butyric oxetane dendron ester (C-PCBOD) is used to improve the mechanical stability of methylammonium lead iodide (MAPbI3 ) perovskite films. Also, it is demonstrated that C-PCBOD passivates the grain boundaries, which reduces the formation of trap states and enhances the environmental stability of MAPbI3 . Thus, MAPbI3 perovskite solar cells are prepared on solid and flexible substrates with record efficiencies of 20.4% and 18.1%, respectively, which are among the highest ever reported for MAPbI3 on both flexible and solid substrates. The result of this work provides a step improvement toward stable and efficient flexible perovskite solar cells.
RESUMO
Integrating an additional component featuring complementary light absorption into binary polymer solar cells is a superior tactic to ameliorate solar cell efficiency and stability. An appropriate additive not only extends the absorption range but may also facilitate charge separation and transport processes. In this work, we elucidate the effects of incorporating a porphyrin-containing conjugated polymer (PPor-1), which displays absorption in 350-500 nm, into binary PTB7-Th:4TIC and PTB7-Th:ITIC blends, affording devices with an average power conversion efficiency approaching 9%. We successfully demonstrate that PPor-1 can be incorporated as an additive to impart improved Jsc (up to 19.1 mA cm-2).
RESUMO
The device performance of inverted organic metallohalide perovskite solar cells (OMPSCs) is optimized via tailoring the electrode surfaces with electron- and hole-transporting materials. This work demonstrates the fabrication of PEDOT:PSS-free OMPSCs using a hole-transporting composite material consisting of bilayered vanadium oxide (VO x) and a thermally cross-linked triarylamine-based material X-DVTPD, which contributes to higher Voc and Jsc values. The hydrophobicity of X-DVTPD resulted in the formation of large perovskite crystals and enhanced the stability of OMPSCs. Integration of ionic fullerene derivative, fulleropyrrolidinium iodide, in OMPSCs as a hole-blocking interfacial layer at the interface with Ag proves effective to further boost the device efficiency to 18.08%.