Influence of thickness and strength on plastic instability in tailored steel structures.

A mathematical model was intricately devised to explore the influence of continuous variations in thickness and mechanical properties on the performance of tailor rolled blanks (TRB) and tailor rolled tubes (TRT). Through the integration of analytical and numerical techniques, it was discerned that these variations play a pivotal role in modulating stress distribution and strain localization, thereby inducing a spectrum of plastic instability behaviors within the structures. The introduction of an 'equivalent strength' metric as a novel means to quantify structural performance shed light on strategic material distribution to enhance durability and mechanical efficiency. Moreover, the insights garnered from this research deepen the understanding of the mechanical responses of tailor-rolled constructs under varying loads, offering valuable perspectives for the development and fabrication of engineered materials with bespoke properties. This study not only contributes to bridging a knowledge gap in the realm of tailored material engineering but also fosters the advancement of design methodologies in the construction of high-performance engineered structures.

Analysis of the Asymmetrical Rolling of Ultra-Thin Strips Considering Elastic Deformation of the Strips.

In normal cold rolling, the elastic deformation of the strip is typically ignored because of the dominant plastic deformation. However, this neglect may introduce additional errors when the strip is very thin. The aim of this study is to investigate the characteristics of the deformation region and thickness reduction in the asymmetrical rolling of ultra-thin strips. Mathematical models were developed based on the slab method, with consideration of the elastic deformation of the strips, and employed in the simulation calculation. The percentage of the three zones and the thickness reduction were analyzed using the simulation results. An increase in the speed ratio results in an increase in the reduction ratio, which is influenced by parameters, such as front tension, back tension, friction coefficient, and entry thickness. The elastic deformation of the strip reduces the tension and the roll pressure and causes the reduction ratio to decrease. The findings and conclusions of this study may be helpful to the mill operating in the asymmetrical rolling process of ultra-thin strips.

Forming Characteristics of Tailor Rolled Blank of Aluminum Alloy during Three-Point Bending.

This paper presents an investigation on the forming characteristics of the tailor rolled blank of an aluminum alloy (Al-TRB) during three-point bending at room temperature through experiments and finite element simulations. The strain distribution, spring-back characteristics, and metal flow law of 6000 series Al-TRB during three-point bending are explored. The prepared Al-TRB has good bending properties, and no surface cracks appear in the bending region of the Al-TRB when bent to 180°. Surface roughening occurs on the outside of the bending region. Since the strain in the thick zone is greater than that in the thin zone, the surface roughening in the thick zone is more obvious than that in the thin zone. The spring-back angle in the thin zone is higher than that in the thick zone after three-point bending, and the overall spring-back angle of Al-TRB becomes larger with an increasing bending angle. When the transition zone of Al-TRB is centered and the length of the transition zone is certain, as the length of the equal-thickness zone increases, the spring-back angle of the thin zone is larger, while the spring-back angle of the thick zone is smaller. Under the premise of a certain total length of Al-TRB and the length of the transition zone, the larger the length proportion of the thin zone, the larger the overall spring-back angle of Al-TRB, and the larger the length proportion of the thick zone, the smaller the overall spring-back angle of Al-TRB. In addition, a slight metal flow phenomenon exists during three-point bending, which shows that the metal in the bending region will flow to the thick zone, and the metal at the edge will flow to the thin zone. At the same time, there are localized thickening and thinning phenomena in Al-TRB. This study is helpful because it provides theoretical guidance for designing molds for the actual production of Al-TRB parts for automotives.

Review on Cellular Automata for Microstructure Simulation of Metallic Materials.

The cellular automata (CA) method has played an important role in the research and development of metallic materials. CA can interpret the microstructure changes of materials and obtain more abundant, accurate and intuitive information of microstructure evolution than conventional methods. CA can visually represent the process of grain formation, growth, development and change to us in a graphical way, which can assist us in analysis, thinking and solving problems. In the last five years, the application of CA in materials research has been rapidly developed, and CA has begun to occupy an increasingly important position in the simulation research of metallic materials. After introducing the advantages and limitations of CA compared to other widely used simulation methods, the purpose of this paper is to review the recent application progress on the microstructure simulation of metallic materials using CA, such as solidification, recrystallization, phase transformation and carbide precipitation occurring during forming and heat treatment. Specifically, recent research advances on microstructure simulation by CA in the fields of additive manufacturing, welding, asymmetrical rolling, corrosion prevention, etc., are also elaborated in this paper. Furthermore, this paper points out the future work direction of CA simulation in the research of metallic materials, especially in the simulation of the crystal structure, the prediction of mechanical properties, CA simulation software and rule systems, etc. These are expected to attract wide attention of researchers in the field of metallic materials and promote the development of CA in materials research.

Microstructure and Mechanical Properties of Ti/Al-SiC/Ti Clad Plates Prepared via the Powder-in-Tube Method.

SiC particle-reinforced Ti/Al/Ti clad plates were successfully fabricated by the powder-in-tube method. The surface micrography, element diffusion, peeling strength and tensile property of clad plates were studied after annealing and cold rolling. The experimental results show that 6 wt.% is optimal. The presence of SiC particles has been seen to significantly enhance the diffusion of Ti and Al elements. Additionally, it has been observed that the diffusion width of the intermetallic compound (IMC) increases as the size of SiC particles grows. However, it is worth noting that the average of Ti/Al-SiC/Ti clad plates initially increases and subsequently falls. The optimized diffusion thickness of the Ti/Al-SiC/Ti clad plate's IMC layer determined via the powder-in-tube method is approximately 4.5 µm. The 1 µm SiC-reinforced Ti/Al/Ti clad plate can obtain the best mechanical properties after annealing at 500 °C and further hot rolling, and the peeling strength, ultimate tensile strength and elongation are 31.5 N/mm, 305 MPa and 26%, respectively. The efficacy of Ti/Al-SiC/Ti clad plates in delivering exceptional performance is substantiated by the analysis of peeling surfaces, peeling tests and tensile testing, which collectively demonstrate the presence of compact and homogenous intermetallic compounds.

Analysis of Mechanical Parameters in Multi-Pass Asymmetrical Rolling of Strip by Slab Method.

Mechanical parameters, time consumption and energy consumption are important considerations in the application of a certain rolling process. This study aims to investigate characteristics of the roll force, roll torque, roll power, rolling time and total work in multi-pass asymmetrical rolling of strip. Mathematic models were built using the slab method to calculate parameters in the asymmetrical rolling process, and the characteristics of these parameters were analyzed on the basis of simulation results. Mechanical parameters are affected by the change of deformation region type. When the speed ratio is less than the critical speed ratio, the roll force, absolute values of roll torque and roll power are found to increase with the increase in the speed ratio. After the speed ratio reaches the critical speed ratio, the roll force, roll torque and lower roll power keep constant, but the upper roll power continues increasing. The upper roll torque and upper roll power required by asymmetrical rolling are much greater than that by symmetrical rolling, which indicates that stronger drive shafts and more powerful drive motors are required by asymmetrical rolling. Compared with symmetrical rolling, asymmetrical rolling requires less roll force to obtain the same thickness reduction, especially for thin and hard strips. Rolling time can be saved at the cost of more energy consumption by using asymmetrical rolling with the same roll force to attain the same final thickness. The results and conclusions of this study can provide a reference for mill design and application of asymmetrical rolling in strip manufacturing.

Effects of Cold Rolling Reduction on Microstructure, Thickness, Adhesive Force of Al-Si Coating and on Bending Toughness of Al-Si Coated Press-Hardened Steel.

Al-Si coated press-hardened steel (PHS) is widely used along with the development of light-weight vehicles, and the tailor-rolled blank parts based on Al-Si coated PHS have attracted much attention. The preparation process includes cold rolling, austenitization, hot-stamping, and quenching. The most widely used AS60/60 coating will change after cold rolling and austenitization, which has been little-studied. Herein, the effects of cold rolling reduction on the microstructure, thickness, adhesive force of AS60/60 coating and on bending toughness of AS60/60 coated PHS were studied. As the cold rolling reduction ratio increased from 0% to 50%, the coatings were gradually thinned, but the overall continuity was unchanged. When the reduction ratio was 40% or above, rapid diffusion channels were formed. The adhesive force of coatings was 21.50-22.15 MPa. After austenitization, the coating thickness gradually decreased as the cold rolling reduction ratio rose from 0% to 50%, but the structure and overall continuity were both unchanged, and the adhesive force was 21.60-22.40 MPa. The rapid diffusion channels promoted the transition from brittle Fe2Al5 to tough FeAl during austenitization, leading to a rapid increment in bending toughness after Al-Si coated PHS was quenched. When the reduction ratio was 50%, the bending angle was improved by 23%.

Softening Effect on Fracture Stress of Pure Copper Processed by Asynchronous Foil Rolling.

In order to study the size effect on the mechanical property of micro-scale metal, pure copper strips with thicknesses in the range of 20 µm to 600 µm were obtained through the asynchronous foil rolling technology. Progressive mechanical property tests indicated that the pure copper experiences softening effect at a micro-scale when the thickness is below 80 µm, which is contrary to the traditional work hardening theory. The related mechanisms were analyzed and discussed through the observation of microstructure and fracture morphology. The decrease of fracture stress with the decrease of thickness can be attributed to the decreased interfacial energy and dislocation density, which contributes to the release of the cumulative distortion energy and the tendency to soften. In addition, the distribution of misorientation angle and changed Taylor factor with the decrease of thickness are other important factors. The fracture morphology indicated a reduction in the number of micro-voids and the nature of fracture transformed from dimpled pattern to knife edge rupture with thickness. The traditional Hall-Petch relationship is no longer applicable due to the softening effect. A modified Hall-Petch relation considering the distribution of misorientation angle and Taylor factor was established, which provided a better relationship between flow stress and grain size.

Determination of organophosphorus pesticides in ecological textiles by solid-phase microextraction with a siloxane-modified polyurethane acrylic resin fiber.

A novel solid-phase microextraction (SPME) fiber coating was prepared with siloxane-modified polyurethane acrylic resin by photo-cured technology. The ratio of two monomers was investigated to obtain good microphase separation structure and better extraction performance. The self-made fiber was then applied to organophosphorus pesticides (OPPs) analysis and several factors, such as extraction/desorption time, extraction temperature, salinity, and pH, were studied. The optimized conditions were: 15 min extraction at 25 °C, 5% Na(2)SO(4) content, pH 7.0 and 4 min desorption in GC inlet. The self-made fiber coating exhibited better extraction efficiency for OPPs, compared with three commercial fiber coatings. Under the optimized conditions, the detection limits of 11 OPPs were from 0.03 µg L(-1) to 0.5 µg L(-1). Good recoveries and repeatabilities were obtained when the method was used to determine OPPs in ecological textile.