Amino-Modified Graphene Oxide from Kish Graphite for Enhancing Corrosion Resistance of Waterborne Epoxy Coatings.

Waterborne epoxy (WEP) coatings with enhanced corrosion resistance were prepared using graphene oxide (GO) that was obtained from kish graphite, and amino-functionalized graphene oxide (AGO) was modified by 2-aminomalonamide. The structural characteristics of the GO and AGO were analyzed using X-ray diffraction (XRD), Raman spectroscopy, Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). And the anti-corrosive performance of waterborne epoxy-cased composite coatings with different addition amounts of AGO was investigated using electrochemical measurements, pull-off adhesion tests, and salt spray tests. The results indicate that AGO15/WEP with 0.15 wt.% of AGO has the best anti-corrosive performance, and the lowest frequency impedance modulus increased from 1.03 × 108 to 1.63 × 1010 ohm·cm-2 compared to that of WEP. Furthermore, AGO15/WEP also demonstrates the minimal corrosion products or bubbles in the salt spray test for 200 h, affirming its exceptional long-term corrosion protection capability.

Porous nitrogen-doped reduced graphene oxide-supported CuO@Cu2O hybrid electrodes for highly sensitive enzyme-free glucose biosensor.

Constructing high-performance enzyme-free biosensors for detecting glucose is essential to preliminary diabetes diagnosis. Here, copper oxide nanoparticles (CuO@Cu2O NPs) were anchored in porous nitrogen-doped reduced graphene oxide (PNrGO) to construct CuO@Cu2O/PNrGO/GCE hybrid electrode for sensitive detection of glucose. Benefiting from the remarkable synergistic effects between the multiple high activation sites of CuO@Cu2O NPs and the dramatic properties of PNrGO with excellent conductivity and large surface area with many accessible pores, the hybrid electrode possesses outstanding glucose sensing performance that is far superior to those of pristine CuO@Cu2O electrode. The as-fabricated enzyme-free glucose biosensor displays prominent glucose sensitivity of 2,906.07 µA mM-1 cm-2, extremely low limit of detection of 0.13 µM, and wide linear detection of 3 µM-6.772 mM. In addition, excellent reproducibility, favorable long-term stability, and distinguished selectivity are obtained in the glucose detection. Importantly, this study provides promising results for continuous improvement of non-enzyme sensing applications.

Molecular Evolution of Plant 14-3-3 Proteins and Function of Hv14-3-3A in Stomatal Regulation and Drought Tolerance.

Drought significantly affects stomatal regulation, leading to the reduced growth and productivity of plants. Plant 14-3-3 proteins were reported to participate in drought response by regulating the activities of a wide array of target proteins. However, the molecular evolution, expression pattern and physiological functions of 14-3-3s under drought stress remain unclear. In this study, a comparative genomic analysis and the tissue-specific expression of 14-3-3s revealed the highly conserved and early evolution of 14-3-3s in green plants and duplication and expansion of the 14-3-3s family members in angiosperms. Using barley (Hordeum vulgare) for the functional characterization of 14-3-3 proteins, the transcripts of five members out of six Hv14-3-3s were highly induced by drought in the drought-tolerant line, XZ141. Suppression of the expression of Hv14-3-3A through barley stripe mosaic virus-virus induced gene silencing resulted in significantly increased drought sensitivity and stomatal density as well as significantly reduced net CO2 assimilation (A) and stomatal conductance (gs) in barley. Moreover, we showed the functional interactions between Hv14-3-3s and key proteins in drought and stomatal responses in plants-such as Open Stomata 1 (HvOST1), Slow Anion Channel 1 (HvSLAC1), three Heat Shock Proteins (HvHSP90-1/2/5) and Dehydration-Responsive Element-Binding 3 (HvDREB3). Taken together, we propose that 14-3-3s are highly evolutionarily conserved proteins and that Hv14-3-3s represent a group of the core regulatory components for the rapid stomatal response to drought in barley. This study will provide important evolutionary and molecular evidence for future applications of 14-3-3 proteins in breeding drought-tolerant crops in a changing global climate.

Adsorption removal of styrene on C-Cl grafted silica gel adsorbents.

The heat desorption of styrene from adsorbents is impracticable owing to its spontaneous polymerization under heating conditions. However, the feature also brings a potential promoting effect on styrene adsorption. Therefore, it is expected to develop the non-regenerative adsorbents with large adsorption capacity by strengthening the polymerization effect. In this work, C-Cl grafted silica gel adsorbents were prepared by introducing (Chloromethyl)dimethylchlorosilane (CMDMCS) and FeCl2 into silica gel. The C-Cl grafted silica gel exhibited excellent styrene adsorption performance, its adsorption amounts for styrene were 4.67 times and 9 times of unmodified silica gel under dry air condition and high humidity condition (RH = 80%), respectively. In addition, the adsorption of styrene on C-Cl grafted silica gel was almost unaffected by the presence of toluene. The characterization of adsorbents after styrene adsorption indicated that the improvement of adsorption capacity of C-Cl grafted silica gel for styrene can be attributed to atom transfer radical polymerization (ATRP) of styrene molecules on modified silica gel during adsorption process.

Re-understanding and focusing on normoalbuminuric diabetic kidney disease.

Diabetes mellitus (DM) has grown up to be an important issue of global public health because of its high incidence rate. About 25% of DM patients can develop diabetic foot/ulcers (DF/DFU). Diabetic kidney disease (DKD) is the main cause of end-stage kidney disease (ESKD). DF/DFU and DKD are serious complications of DM. Therefore, early diagnosis and timely prevention and treatment of DF/DFU and DKD are essential for the progress of DM. The clinical diagnosis and staging of DKD are mostly based on the urinary albumin excretion rate (UAER) and EGFR. However, clinically, DKD patients show normoalbuminuric diabetic kidney disease (NADKD) instead of clinical proteinuria. The old NADKD concept is no longer suitable and should be updated accordingly with the redefinition of normal proteinuria by NKF/FDA. Based on the relevant guidelines of DM and CKD and combined with the current situation of clinical research, the review described NADKD from the aspects of epidemiology, pathological mechanism, clinical characteristics, biomarkers, disease diagnosis, and the relationship with DF/DFU to arouse the new understanding of NADKD in the medical profession and pay attention to it.

Adsorptive removal of gas phase naphthalene on ordered mesoporous carbon.

Adsorptive removal of gas phase low concentration macromolecular organic component, represented by naphthalene, from the enclosed space using ordered mesoporous carbon (OMC) has been studied by molecular simulation and experimental investigation. The simulation results indicated that both adsorption capacity and adsorption stability of the OMCs for naphthalene decreased with the increase of pore sizes from 2 nm to 8 nm. Characterizations showed that the prepared OMCs had the pore structure similar to the simulated OMCs except for the rough surface. In particular, the adsorption performance of the prepared OMCs was significantly lower than that of the simulated OMCs when pore size was 2 nm and 3 nm, which was attributed to the rough inner surface of these adsorbents, blocking the narrow pore channels and significantly reducing the pore volume. OMC with pore size of 4 nm had the highest adsorption amount for naphthalene. The co-adsorption experiments in the presence of both naphthalene and toluene, acetone or water showed the adsorption performance of OMCs for naphthalene were almost unaffected by the presence of low concentration toluene and acetone, as well as high relative humidity.

Exfoliated graphite blocks with resilience prepared by room temperature exfoliation and their application for oil-water separation.

Exfoliated graphite (EG) blocks are prepared from the ultra-large flakes of graphite by intercalation of H2SO4 using a large amount of H2O2 at 5 °C and following exfoliation at 30 °C. By the exfoliation in a closed container, EG blocks with the bulk densities of 0.008-0.024 g/cm3 are successfully prepared. The resultant EG blocks have high sorption capacities for a diesel oil, up to 45 g/g. The EG blocks after oil sorption can get certain resilience for compressive stress with high reproducibility by compression-release cycles, which allows us to apply the compression-releasing for the oil sorption-desorption of the EG blocks. The performance of cyclic oil sorption-desorption by compression-releasing of EG block is compared with those of filtration and distillation. Since the resultant EG blocks had sufficient mechanical strength, the continuous removal of oil floating on the water surface is possible, exporting oil through a catheter inserted into the block and connected to a peristaltic pump. By warming up by Joule heating, even a crude oil having high viscosity can be continuously removed from the water with sufficient rate. The high hydrophobicity and lipophilicity of EG make selective removal of oil from water possible.

A Highly Sensitive Electrochemical Glucose Sensor Based on Room Temperature Exfoliated Graphite-Derived Film Decorated with Dendritic Copper.

An ultrasensitive enzyme-free glucose sensor was facilely prepared by electrodepositing three-dimensional dendritic Cu on a room temperature exfoliated graphite-derived film (RTEG-F). An excellent electrocatalytic performance was demonstrated for glucose by using Cu/RTEG-F as an electrode. In terms of the high conductivity of RTEG-F and the good catalytic activity of the dendritic Cu structures, the sensor demonstrates high sensitivities of 23.237 mA/mM/cm2, R2 = 0.990, and 10.098 mA/mM/cm2, R2 = 0.999, corresponding to the concentration of glucose ranging from 0.025 mM to 1.0 mM and 1.0 mM to 2.7 mM, respectively, and the detection limit is 0.68 µM. In addition, the Cu/RTEG-F electrode demonstrates excellent anti-interference to interfering species and a high stability. Our work provides a new idea for the preparation of high-performance electrochemical enzyme-free glucose sensor.

Combining Multiple Methods for Recycling of Kish Graphite from Steelmaking Slags and Oil Sorption Performance of Kish-Based Expanded Graphite.

The utilization of industrial waste as renewable resources is an essential issue of sustainable development. Kish graphite is a precipitate of excess carbon generated during the cooling of molten iron and one of the byproducts associated with steel slags. The scale-up recycling of kish graphite from steelmaking slags is a promising way to develop natural graphite alternatives. However, only one means cannot work efficiently because of the unusual occurrence of associated impurities; combining multiple separation methods is the solution. In this paper, we proposed an integrated beneficiation process, pneumatic separation-flotation-sonication-magnetic separation, to recycle kish graphite flakes with a high graphitization degree and investigated the sorption performance of various oils on kish-based expanded graphite. The new process avoided shortages such as the sediments of iron particles in the flotation cell and the loss of clean graphite in the magnetic separation. Consequently, the carbon content of kish graphite reached ∼95% after separation and >99% after acid leaching. The macroscopic structural defects of kish particles created more active sites, made the intercalation of KG-GICs faster, and yielded better-staged compounds. The kish graphite-based expanded graphite presented an octopus-like shape and exhibited an expansion volume of ∼150 mL/g. Furthermore, the developed macropore structure of the obtained kish graphite-based expanded graphite led to a superior sorption performance for oils. This work supplies one feasible and promising way to recycle kish graphite from steelmaking slags and use it.

One-step green fabrication of hierarchically porous hollow carbon nanospheres (HCNSs) from raw biomass: Formation mechanisms and supercapacitor applications.

Hierarchical porous hollow carbon nanospheres (HCNSs) were fabricated directly from raw biomass via a one-step method, in which HCNSs were obtained by thermal treatment of raw biomass in the presence of polytetrafluoroethylene (PTFE). The HCNSs possess coupling merits of uniformly distributed hollow spherical architectures, and high specific surface area, abundant accessible/open micropores and reasonable mesopores, the HCNS-based electrodes deliver high electrochemical capacitance. The formation mechanisms of pores and hollow core-shell structures were explored thoroughly, it is found that the key to the formation of hollow core-shell structure is the onset-pyrolysis temperature difference between raw biomass and PTFE. Moreover, the content of silica had significant effects on the textures of HCNSs, and HCNS with the largest SSA of 1984 m2/g was obtained. Accordingly, a possible mechanism of HCNSs formation was proposed here, where PTFE acted as the pore creation and nucleation agents and raw biomasses were the primary carbon precursors.

Asymmetric Supercapacitors Based on Hierarchically Nanoporous Carbon and ZnCo2O4 From a Single Biometallic Metal-Organic Frameworks (Zn/Co-MOF).

Metal-organic framework (MOF)-derived nanoporous carbons (NPCs) and porous metal oxide nanostructures or nanocomposites have gathered considerable interest due to their potential use in supercapacitor (SCs) applications, owing to their precise control over porous architectures, pore volumes, and surface area. Bimetallic MOFs could provide rich redox reactions deriving from improved charge transfer between different metal ions, so their supercapacitor performance could be further greatly enhanced. In this study, "One-for-All" strategy is adopted to synthesize both positive and negative electrodes for hybrid asymmetric SCs (ASCs) from a single bimetallic MOF. The bimetallic Zn/Co-MOF with cuboid-like structures were synthesized by a simple method. The MOF-derived nanoporous carbons (NPC) were then obtained by post-heat treatment of the as-synthesized Zn/Co-MOF and rinsing with HCl, and bimetallic oxides (ZnCo2O4) were achieved by sintering the Zn/Co-MOF in air. The as-prepared MOF-derived NPC and bimetallic oxides were utilized as negative and positive materials to assemble hybrid ASCs with 6 M KOH as an electrolyte. Owing to the matchable voltage window and specific capacitance between the negative (NPC) and positive (ZnCo2O4), the as-assembled ASCs delivered high specific capacitance of 94.4 F/g (cell), excellent energy density of 28.6 Wh/kg at a power density of 100 W/kg, and high cycling stability of 87.2% after 5,000 charge-discharge cycles. This strategy is promising in producing high-energy-density electrode materials in supercapacitors.

Blow-spun N-doped carbon fiber based high performance flexible lithium ion capacitors.

Constructing flexible hybrid supercapacitors is a feasible way to achieve devices with high energy density, high power density and flexibility at the same time. Herein, flexible asymmetric hybrid supercapacitors are fabricated with blow spun activated carbon fibers. Owing to the highly effective conductive network, abundant nitrogen doping, optimized pore-structure and surface chemical properties of the carbon fibers, the as-prepared flexible hybrid supercapacitor shows outstanding energy and power performance (98 W h kg-1 (0.3 mW h cm-2) @ 400 W kg-1, 9 W h kg-1 @ 34 kW kg-1), as well as excellent cycle stability with 93% capacitance retention after 4000 cycles.

Na0.76V6O15/Activated Carbon Hybrid Cathode for High-Performance Lithium-Ion Capacitors.

Lithium-ion hybrid capacitors (LICs) are regarded as one of the most promising next generation energy storage devices. Commercial activated carbon materials with low cost and excellent cycling stability are widely used as cathode materials for LICs, however, their low energy density remains a significant challenge for the practical applications of LICs. Herein, Na0.76V6O15 nanobelts (NaVO) were prepared and combined with commercial activated carbon YP50D to form hybrid cathode materials. Credit to the synergism of its capacitive effect and diffusion-controlled faradaic effect, NaVO/C hybrid cathode displays both superior cyclability and enhanced capacity. LICs were assembled with the as-prepared NaVO/C hybrid cathode and artificial graphite anode which was pre-lithiated. Furthermore, 10-NaVO/C//AG LIC delivers a high energy density of 118.9 Wh kg-1 at a power density of 220.6 W kg-1 and retains 43.7 Wh kg-1 even at a high power density of 21,793.0 W kg-1. The LIC can also maintain long-term cycling stability with capacitance retention of approximately 70% after 5000 cycles at 1 A g-1. Accordingly, hybrid cathodes composed of commercial activated carbon and a small amount of high energy battery-type materials are expected to be a candidate for low-cost advanced LICs with both high energy density and power density.

Advanced Materials for Sodium-Ion Capacitors with Superior Energy-Power Properties: Progress and Perspectives.

Developing electrochemical energy storage devices with high energy-power densities, long cycling life, as well as low cost is of great significance. Sodium-ion capacitors (NICs), with Na+ as carriers, are composed of a high capacity battery-type electrode and a high rate capacitive electrode. However, unlike their lithium-ion analogues, the research on NICs is still in its infancy. Rational material designs still need to be developed to meet the increasing requirements for NICs with superior energy-power performance and low cost. In the past few years, various materials have been explored to develop NICs with the merits of superior electrochemical performance, low cost, good stability, and environmental friendliness. Here, the material design strategies for sodium-ion capacitors are summarized, with focus on cathode materials, anode materials, and electrolytes. The challenges and opportunities ahead for the future research on materials for NICs are also proposed.

From upcycled waste polyethylene plastic to graphene/mesoporous carbon for high-voltage supercapacitors.

We report a successful design and synthesis method for developing a graphene/mesoporous carbon (G@PE40-MC700) electrode materials from upcycled waste polyethylene (PE) plastic combined with graphene oxide (GO) and flame retardant by low-temperature carbonization at 700 °C. The G@PE40-MC700 exhibits a high surface area (1175 m2 g-1) and a considerable amount of mesopores (2.30 cm3 g-1), thus improved electrochemical performance in both symmetric and hybrid supercapacitors with wide voltage windows. The hybrid supercapacitor assembled from G@PE40-MC700 as anode and LiMn2O4 as cathode operating at 2.0 V in 0.5 M Li2SO4 was investigated. The hybrid supercapacitor delivers an energy density of 47.8 Wh kg-1 at a power density of 250 W kg-1, as well as high cycling stability of 83.8 % after 5000 cycles. Furthermore, the much higher energy density of 63.3 Wh kg-1 by using G@PE40-MC700 as electrode material was achieved in high-voltage (4.0 V) symmetric supercapacitors using 1-ethyl-3-methylimidazolium tetrafluoroborate (EMIMBF4) as the electrolyte with enhanced cycling stability of 89.3% after 5000 cycles. The high capacitance and rate capability of G@PE40-MC700 can be attributed to the synergistic effect of graphene and the mesoporous carbon composites. Our work not only offers a sustainable approach to turn waste plastic into valuable carbon materials but also an opportunity for its applications in "gold capacitors."

Steam Selective Etching: A Strategy to Effectively Enhance the Flexibility and Suppress the Volume Change of Carbonized Paper-Supported Electrodes.

Paper-supported electrodes with high flexibility have attracted much attention in flexible Li-ion batteries. However, they are restricted by the heavy inactive paper substrate and large volume change during the lithiation-delithiation process, which will lead to low capacity and poor rate capability and cyclability. Converting the paper substrate to carbon fiber by carbonization can substantially eliminate the "dead mass", but it becomes very brittle. This study reports a water-steam selective etching strategy that successfully addresses these problems. With the help of steam etching, pores are created, and transition-metal oxides are embedded into the fiber. These effectively accommodate the volume change and enhances the kinetics of ion and electron transport. The pores release the mechanical stress from bending, ensuring the sufficient bendability of carbonized paper. Benefiting from these merits, the steam-etched samples show high flexibility and possess outstanding electrochemical performance, including ultra-high capacity and superior cycling stability with capacity retention over 100% after 1500 cycles at 2 A g-1. Furthermore, a flexible Li-ion full battery using the steam-etched Fe2O3@CNF anode and LiFePO4/steam-etched CNF cathode delivers a high capacity of 623 mAh g-1 at 100 mA g-1 and stable electrochemical performances under the bent state, holding great promise for next-generation wearable devices.

Sulfur-Doped Reduced Graphene Oxide for Enhanced Sodium Ion Pseudocapacitance.

Sodium-ion capacitors (NICs) are considered an important candidate for large-scale energy storage in virtue of their superior energy-power properties, as well as availability of rich Na+ reserves. To fabricate high-performance NIC electrode material, a hydrothermal method was proposed to synthesize sulfur-doped reduced graphene oxide (SG), which exhibited unique layered structures and showed excellent electrochemical properties with 116 F/g capacitance at 1 A/g as the cathode of NICs from 1.6 V to 4.2 V. At the power-energy density over 5000 W/kg, the SG demonstrated over 100 Wh/kg energy density after 3500 cycles, which indicated its efficient durability and superior power-energy properties. The addition of a sulfur source in the hydrothermal process led to the higher specific surface area and more abundant micropores of SG when compared with those of reduced graphene oxide (rGO), thus SG exhibited much better electrochemical properties than those shown by rGO. Partially substituting surface oxygen-containing groups of rGO with sulfur-containing groups also facilitated the enhanced sodium-ion storage ability of SG by introducing sufficient pseudocapacitance.

Building Carbon-Based Versatile Scaffolds on the Electrode Surface to Boost Capacitive Performance for Fiber Pseudocapacitors.

In order to fabricate high performance fiber pseudocapacitors, the trade-off between high mass loading and high utilization efficiency of pseudocapacitive materials should be carefully addressed. Here, a solution that is to construct a carbon-based versatile scaffold is reported for loading pseudocapacitive materials on carbonaceous fibers. The scaffold can be easily built by conformally coating commercial pen ink on the fibers without any destruction to the fiber skeleton. Due to the high electrical conductivity and abundant macropore structure, it can provide sufficient loading room and a high ion/electron conductive network for pseudocapacitive materials. Therefore, their loading mass and utilization efficiency can be increased simultaneously, and thus the as-designed fibrous electrode displays a high areal capacitance of 649 mF cm-2 (or 122 mF cm-1 based on length), which is higher than most of the reported fiber pseudocapacitors. The simple and low-cost strategy opens up a new way to prepare high performance portable/wearable energy storage devices.

MoS2/carbon composites prepared by ball-milling and pyrolysis for the high-rate and stable anode of lithium ion capacitors.

Lithium ion capacitors (LICs), bridging the advantages of batteries and electrochemical capacitors, are regarded as one of the most promising energy storage devices. Nevertheless, it is always limited by the anodes that accompany with low capacity and poor rate performance. Here, we develop a versatile and scalable method including ball-milling and pyrolysis to synthesize exfoliated MoS2 supported by N-doped carbon matrix derived from chitosan, which is encapsulated by pitch-derived carbon shells (MoS2/CP). Because the carbon matrix with high nitrogen content can improve the electron conductivity, the robust carbon shells can suppress the volume expansion during cycles, and the sufficient exfoliation of lamellar MoS2 can reduce the ions transfer paths, the MoS2/CP electrode delivers high specific capacity (530 mA h g-1 at 100 mA g-1), remarkable rate capability (230 mA h g-1 at 10 A g-1) and superior cycle performance (73% retention after 250 cycles). Thereby, the LICs, composed of MoS2/CP as the anode and commercial activated carbon (21 KS) as the cathode, exhibit high power density of 35.81 kW kg-1 at 19.86 W h kg-1 and high energy density of 87.74 W h kg-1 at 0.253 kW kg-1.

Facile synthesis of bimodal macroporous g-C3N4/SnO2 nanohybrids with enhanced photocatalytic activity.

It is of vital importance to construct highly interconnected, macroporous photocatalyst to improve its efficiency and applicability in solar energy conversion and environment remediation. Graphitic-like C3N4 (g-C3N4), as an analogy to two-dimensional (2D) graphene, is highly identified as a visible-light-responsive polymeric semiconductor. Moreover, the feasibility of g-C3N4 in making porous structures has been well established. However, the preparation of macroporous g-C3N4 with abundant porous networks and exposure surface, still constitutes a difficulty. To solve it, we report a first facile preparation of bimodal macroporous g-C3N4 hybrids with abundant in-plane holes, which is simply enabled by in-situ modification through thermally treating the mixture of thiourea and SnCl4 (pore modifier) after rotary evaporation. For one hand, the formed in-plane macropores endow the g-C3N4 system with plentiful active sites and short, cross-plane diffusion channels that can greatly speed up mass transport and transfer. For another, the heterojunctions founded between g-C3N4 and SnO2 consolidate the electron transfer reaction to greatly reduce the recombination probability. As a consequence, the resulted macroporous g-C3N4/SnO2 nanohybrid had a high specific surface area (SSA) of 44.3 m2/g that was quite comparable to most nano/mesoporous g-C3N4 reported. The interconnected porous network also rendered a highly intensified light absorption by strengthening the light penetration. Together with the improved mass transport and electron transfer, the macroporous g-C3N4/SnO2 hybrid exhibited about 2.4-fold increment in the photoactivity compared with pure g-C3N4. Additionally, the recyclability of such hybrid could be guaranteed after eight successive uses.