On the removal of hexavalent chromium from a Class F fly ash.

Coarse and fine samples of a Class F fly ash obtained from commercial combustion of Illinois bituminous coal have been exposed to two long-term leaching tests designed to simulate conditions in waste impoundments. ICP-AES analysis indicated that the coarse and fine fly ash samples contained 135 and 171mg/kg Cr, respectively. Measurements by XAFS spectroscopy showed that the ash samples originally contained 5 and 8% of the chromium, respectively, in the hexavalent oxidation state, Cr(VI). After exposure to water for more than four months, the percentage of chromium as Cr(VI) in the fly-ash decreased significantly for the coarse and fine fly-ash in both tests. Combining the XAFS data with ICP-AES data on the concentration of chromium in the leachates indicated that, after the nineteen-week-long, more aggressive, kinetic test on the coarse fly ash, approximately 60% of the Cr(VI) had been leached, 20% had been reduced to Cr(III) and retained in the ash, and 20% remained as Cr(VI) in the ash. In contrast, during the six-month-long baseline test, very little Cr was actually leached from either the coarse or the fine fly-ash (<0.1mg/kg); rather, about 66% and 20%, respectively, of the original Cr(VI) in the coarse and fine fly-ash was retained in the ash in that form, while the remainder, 34% and 80%, respectively, was reduced and retained in the ash as Cr(III). The results are interpreted as indicating that Cr(VI) present in Class F fly-ash can be reduced to Cr(III) when in contact with water and that such chemical reduction can compete with physical removal of Cr(VI) from the ash by aqueous leaching.

Nitrite reactivity with magnetite.

Under Fe(3+)-reducing conditions, soil Fe(2+) oxidation has been shown to be coupled with nitrate (NO3(-)) reduction. One possible secondary reaction is the involvement of NO3(-) and nitrite (NO2(-)) with magnetite, a mixed valence Fe(2+)/Fe(3+) mineral found in many natural environments. Currently, little information exists on NO3(-) and NO2(-) reactivity with magnetite. This study investigates NO3(-) and NO2(-) reactivity with magnetite under anoxic conditions using batch kinetic experiments across a range of pH values (5.5-7.5) and in the presence of added dissolved Fe(2+). Solid phase products were characterized using X-ray diffraction (XRD), Mössbauer spectroscopy, and scanning electron microscopy (SEM). Nitrate removal by magnetite was much slower when compared with NO2(-). There was a pH-dependence in the reduction of NO2(-) by magnetite; the initial rate of NO2(-) removal was two times faster at pH 5.5 than at pH 7.5. The influence of pH was explained by the binding of NO2(-) to positively charged sites on magnetite (≡ S-OH2(+)) and to neutral sites (≡ S-OH(0)). As NO2(-) was removed from solution, nitric oxide (NO) and nitrous oxide (N2O) were identified as products confirming that nitrite was reduced. Structural Fe(2+) in magnetite was determined to be the reductant of NO2(-) based on the lack of measurable dissolved Fe(2+) release to solution coupled with Mössbauer spectra and XRD analysis of solid phase products. Addition of dissolved Fe(2+) to magnetite slurries resulted in adsorption and an acceleration in the rate of nitrite reduction at a given pH value. In summary, findings reported in this study demonstrate that if magnetite is present in Fe(3+)-reducing soil and NO2(-) is available, it can remove NO2(-) from solution and reduce a portion of it abiotically to NO and subsequently to N2O by a heterogeneous electron transfer process.

The stability of arsenic and selenium compounds that were retained in limestone in a coal gasification atmosphere.

The aim of this work was to evaluate the stability of arsenic and selenium species retained in a lime/limestone mixture obtained by using limestone as a sorbent for gas cleaning in a coal gasification atmosphere. It was found that the stability of arsenic and selenium species produced by the gas-solid reactions with lime/limestone may be affected by their exposure to air and by their contact with water. The results confirm the conclusions of a previous work in which Ca(AsO(2))(2) and CaSe was postulated as the products of the reaction between the arsenic and selenium species present in a coal gasification atmosphere with lime/limestone. Moreover it was proved that the compounds (Ca(AsO(2))(2) and CaSe) may undergo transformations when the sorbents post-retention are stored or disposed of in air. From the results obtained by XAFS it was possible to identify the Ca(3)(AsO(4))(2) produced by the oxidation of the Ca(AsO(2))(2) on the sorbent surface. The XAFS results for selenium showed that the CaSe formed on the sorbent was transformed to form several species, but mainly elemental Se. These changes in the speciation of arsenic and selenium may explain the behavior of the sorbent post-retention during the water solubility test. Although the selenium compounds and the products that may originate from their decomposition in water are not toxic, in the case of arsenic, species like Ca(AsO(2))(2) and Ca(3)(AsO(4))(2) may lixiviate, and generate toxic arsenic compounds in solution that could pose a risk when the sorbent is finally disposed of.

Toward distinguishing woodsmoke and diesel exhaust in ambient particulate matter.

Particulate matter (PM) from biomass burning and diesel exhaust has distinct X-ray spectroscopic, carbon specific signatures, which can be employed for source apportionment. Characterization of the functional groups of a wide selection of PM samples (woodsmoke, diesel soot, urban air PM) was carried out using the soft X-ray spectroscopy capabilities at the synchrotron radiation sources in Berkeley (ALS) and Brookhaven (NSLS). The spectra reveal that diesel exhaust particulate (DEP) matter is made up from a semigraphitic solid core and soluble organic matter, predominantly with carboxylic functional groups. Woodsmoke PM has no or a less prevalent, graphitic signature, instead it contains carbon-hydroxyl groups. Using these features to apportion the carbonaceous PM in ambient samples we estimate that the relative contribution of DEP to ambient PM in an urban area such as Lexington, KY and St. Louis, MO is 7% and 13.5%, respectively. These values are comparable to dispersion modeling data from nonurban and urban areas in California, and with elemental carbon measurements in urban locations such as Boston, MA, Rochester, NY, and Washington, DC.

Cd, Hg, and Pb Compounds of Benzene-1,3-diamidoethanethiol (BDETH(2)).

Benzene-1,3-diamidoethanethiol (BDETH2) is an exceptional precipitant for removing soft heavy metals from water. The present work will detail the bonding arrangement of BDETH2 to the metals Cd, Hg, and Pb, along with the full characterization data of the BDET-M compounds. It was found that the Hg compound has a linear S-M-S geometry. The characterization data consisted of Mp, EA, IR, Raman, MS, XANES, EXAFS, and solid-state multinuclear NMR.

Characterization of ultrafine coal fly ash particles by energy-filtered TEM.

In this study, energy-filtered transmission electron microscopy is demonstrated to be a valuable tool for characterizing ultrafine coal fly ash particles, especially those particles encapsulated in or associated with carbon. By examining a series of elemental maps (K-edge maps of C and O, and L-edge maps of Si, Al, Ti and Fe) recorded using the three-window method, considerable numbers of titanium and iron species with sizes from several nanometres to submicrometre were shown to be present, typically as oxides dispersed in the carbonaceous matrix. Crystalline phases, such as rutile and iron-rich oxide spinel, were also identified from electron diffraction patterns and high-resolution TEM images. Information about these ultrafine coal fly ash particles regarding their size, morphology, elemental composition and distribution, and crystalline phases, which has not been available previously in conventional ash studies, should be useful in toxicological studies and related environmental fields.

Monitoring the species of arsenic, chromium and nickel in milled coal, bottom ash and fly ash from a pulverized coal-fired power plant in western Canada.

The concentration of As, Cr and Ni and their speciation (As3+;5+, Cr3+;6+ and Ni0;2+) in milled coal, bottom ash and ash collected by electrostatic precipitator (ESP) from a coal fired-power plant in western Canada were determined using HGAAS, ICP-AES and XANES. The chemical fractionation of these elements was also determined by a sequential leaching procedure, using deionized water, NH4OAC and HCI as extracting agents. The leachate was analyzed by ICP-AES. Arsenic in the milled coal is mostly associated with organic matter, and 67% of this arsenic is removed by ammonium acetate. This element is totally removed from milled coal after extraction with HCI. Arsenic occurs in both the As3+ and the As5+ oxidation states in the milled coal, while virtually all (>90%) of the arsenic in bottom ash and fly ash appears to be in the less toxic arsenate (As5+) form. Both Ni and Cr in the milled coal are extracted by HCI, indicating that water can mobilize Ni and Cr in an acidic environment. The chromium is leached by water from fly ash as a result of the high pH of the water, which is induced during the leaching. Ammonium acetate removes Ni from bottom ash through an ion exchange process. Chromium in milled coal is present entirely as Cr3+, which is an essential human trace nutrient. The Cr speciation in bottom ash is a more accentuated version of the milled coal and consists mostly of the Cr3+ species. Chromium in fly ash is mostly Cr3+, with significant contamination by stainless-steel from the installation itself.

Nickel speciation of residual oil fly ash and ambient particulate matter using X-ray absorption spectroscopy.

The chemical speciation of Ni in fly ash produced from approximately 0.85 wt % S residual (no. 6 fuel) oils in laboratory (7 kW)- and utility (400 MW)-scale combustion systems was investigated using X-ray absorption fine structure (XAFS) spectroscopy, X-ray diffraction (XRD), and acetate extraction [1 M NaOAc-0.5 M HOAc (pH 5) at 25 degrees C]-anodic stripping voltammetry (ASV). XAFS was also used to determine the Ni speciation of ambient particulate matter (PM) sampled near the 400-MW system. Based on XAFS analyses of bulk fly ash and their corresponding acetate extraction residue, it is estimated that > 99% of the total Ni (0.38 wt %) in the experimentally produced fly ash occurs as NiSO4.xH2O, whereas > 95% of the total Ni (1.70 and 2.25 wt %) in two fly ash samples from the 400-MW system occurs as NiSO4.xH2O and Ni-bearing spinel, possibly NiFe2O4. Spinel was also detected using XRD. Acetate extracts most of the NiSO4.xH2O and concentrates insoluble NiFe2O4 in extraction residue. Similar to fly ash, ambient PM contains NiSO4.xH2O and NiFe2O4; however, the proportion of NiSO4.xH2O relative to NiFe2O4 is much greater in the PM. Results from this and previous investigations indicate that residual oil ash produced in the 7-kW combustion system lack insoluble Ni (e.g., NiFe2O4) but are enriched in soluble NiSO4.xH2O relative to fly ash from utility-scale systems. This difference in Ni speciation is most likely related to the lack of additive [e.g., Mg(OH)2] injection and residence time in the 7-kW combustion system.

Characterization of fine particulate matter produced by combustion of residual fuel oil.

Combustion experiments were carried out on four different residual fuel oils in a 732-kW boiler. PM emission samples were separated aerodynamically by a cyclone into fractions that were nominally less than and greater than 2.5 microns in diameter. However, examination of several of the samples by computer-controlled scanning electron microscopy (CCSEM) revealed that part of the PM2.5 fraction consists of carbonaceous cenospheres and vesicular particles that range up to 10 microns in diameter. X-ray absorption fine structure (XAFS) spectroscopy data were obtained at the S, V, Ni, Fe, Cu, Zn, and As K-edges and at the Pb L-edge. Deconvolution of the X-ray absorption near edge structure (XANES) region of the S spectra established that the dominant molecular forms of S present were sulfate (26-84% of total S) and thiophene (13-39% of total S). Sulfate was greater in the PM2.5 samples than in the PM2.5+ samples. Inorganic sulfides and elemental sulfur were present in lower percentages. The Ni XANES spectra from all of the samples agreed fairly well with that of NiSO4, while most of the V spectra closely resembled that of vanadyl sulfate (VO.SO4.xH2O). The other metals investigated (i.e., Fe, Cu, Zn, and Pb) also were present predominantly as sulfates. Arsenic was present as an arsenate (As+5). X-ray diffraction patterns of the PM2.5 fraction exhibit sharp lines due to sulfate compounds (Zn, V, Ni, Ca, etc.) superimposed on broad peaks due to amorphous carbons. All of the samples contain a significant organic component, with the loss on ignition (LOI) ranging from 64 to 87% for the PM2.5 fraction and from 88 to 97% for the PM2.5+ fraction. Based on 13C nuclear magnetic resonance (NMR) analysis, the carbon is predominantly condensed in graphitic structures. Aliphatic structure was detected in only one of seven samples examined.

Mössbauer spectroscopy indicates that iron in an aluminosilicate glass phase is the source of the bioavailable iron from coal fly ash.

Iron speciation by Mössbauer spectroscopy indicates that ferric iron in an aluminosilicate glass phase is the source of the bioavailable iron in coal fly ash and that this iron species is associated with combustion particles, but not with crustal dust derived from soil minerals. Urban particulate has been shown to be a source of bioavailable iron and has been shown to be able to induce the formation of reactive species in cell culture experiments. Crustal dust and laboratory-generated coal fly ash have been studied as surrogates for two sources of metal-bearing particles in ambient air. As much as a 60-fold difference in the amount of iron mobilized by the chelator citrate was observed between fly ash and crustal dust samples with similar total iron contents. The extent of iron mobilization by citrate in vitro has been shown to correlate with indirect measures of excess iron in cultured cells and with assays for reactive oxygen species generation in vitro. Mössbauer spectroscopy of coal fly ash, before and after treatment with the chelator desferrioxamine B, showed that the iron in an aluminosilicate glass phase was preferentially removed. The removal of the glass-phase iron greatly reduced the amount of iron that could be mobilized by citrate and prevented the particles from inducing interleukin-8 in cultured human lung epithelial (A549) cells. Ferric iron in aluminosilicate glass is associated with particles formed at high temperatures followed by rapid cooling. The observation that ferric iron in aluminosilicate glass is the source of bioavailable iron in coal fly ash suggests that particles from ambient sources and other specific combustion sources should be examined for the presence of this potential source of bioavailable iron.

Microporous Montmorillonites Expanded with Alumina Clusters and M[(&mgr;-OH)Cu(&mgr;-OCH(2)CH(2)NEt(2))](6)(ClO(4))(3), (M = Al, Ga, and Fe), or Cr[(&mgr;-OCH(3))(&mgr;-OCH(2)CH(2)NEt(2))CuCl](3) Complexes.

Expanded clays bipillared with [Al(13)O(4)(OH)(24)(H(2)O)(12)](7+) ions and with hexameric Cu complexes such as M[(&mgr;-OH)Cu(&mgr;-OCH(2)CH(2)NEt(2))](6)(ClO(4))(3), or with M[(&mgr;-OH)Cu(&mgr;-OCH(2)CH(2)NEt(2))](6)(PF(6))(3) where M = Fe, Al, Ga, form microporous materials whose stability and microporosity depend mainly on the identity of the hexamer central metal atom. In fact, a general decrease in thermal stability, interlamellar heights, surface areas, and pore volumes was noted when, in the (Cu,M) hexamer, M changed from gallium to aluminum to iron. Mossbauer results have indicated that only Fe(3+) in octahedral coordination is present in the iron-containing bi-PILC samples (bi-PILC = bipillared interlayered clays). It is believed that metals such as Fe(3+) and Cu(2+) can interact with the interlamellar Keggin ions thereby decreasing the stability of the alumina pillars. In contrast, the intermediate Al(13)-PILC structure is least affected when the more stable Cr complex is used. Bi-PILC materials containing 2.7-3.4% Cr stable to 500 degrees C have been obtained. The low polarity of the chosen solvent (acetonitrile) appears to inhibit the back-exchange of the intermediate PILC's Keggin ions with the hexameric Cu complexes. Elemental analysis together with XRD results suggests that the primary intercalation pathway was diffusion or ion exchange when Cr[(&mgr;-OCH(3))(&mgr;-OCH(2)CH(2)NEt(2))CuCl](3) or M[(&mgr;-OH)Cu(&mgr;-OCH(2)CH(2)NEt(2))](6)(ClO(4))(3), respectively, was used. In all preparations, bi-PILC were produced containing complexes that suffered ligand losses during the synthesis reaction. Molecular scale AFM images have shown that these complexes can be found also outside the clay interlamellar space.

Importance of fasting in the lymphocyte calcium test for malignant hyperthermia.

Anaesthetic-induced increases in cytoplasmic free Ca2+ have been reported to be greater in lymphocytes from malignant hyperthermia (MH) susceptible patients than in those from controls, suggesting that this may be the basis for a less invasive test for MH susceptibility. In the present study the cytoplasmic Ca2+ concentrations of lymphocytes were monitored with indo-1 in 14 control subjects (nine fasted and five nonfasted) and five fasted MH susceptible and three fasted nonsusceptible patients, diagnosed by the halothane and caffeine contracture tests. No relationship was observed between MH susceptibility and Ca2+ concentrations in lymphocytes in the absence or presence of halothane. There was, however, a relationship in control subjects between fasting and the response of lymphocytes to halothane, with the halothane-induced Ca2+ increase being considerably larger in nonfasted subjects.

The importance of calcium ions for in vitro malignant hyperthermia testing.

Intracellular Ca++ levels in skeletal muscle are elevated during the in vitro contracture response of muscle from subjects with malignant hyperthermia. The role of Ca++ in the bathing medium and the consequences of substitution of Sr++ for Ca++ in the response to agents associated with malignant hyperthermia were examined. When Ca++ was omitted from the bathing medium the contractures induced in human vastus lateralis by halothane (three per cent) or succinylcholine (50 mM) were reduced by 80 and 100 per cent, respectively, while contractures induced by caffeine (8 mM) were only reduced by 50 per cent. Substitution of Ca++ by another divalent cation, Sr++, completely restored contractures induced by caffeine, but only partially restored contractures induced by halothane or succinylcholine (to 50 and 30 per cent of Ca(++)-containing medium, respectively). Mepacrine (10 microM) was effective in antagonizing contractures by caffeine, whereas verapamil and nifedipine (10 microM) were not. These results support an essential role for extracellular Ca++ not fulfilled by Sr++ in contracture induction by halothane and succinylcholine, but not by caffeine.

Caffeine and halothane contracture testing in swine using the recommendations of the North American Malignant Hyperthermia Group.

Caffeine and halothane contracture testing is widely used to detect malignant hyperthermia (MH) susceptibility. The accuracy and reliability of the 3% halothane test and the incremental caffeine test, as recommended by the North American MH Group, were assessed in 11 swine (five MHS, six control). Nine swine were tested twice, 4-6 weeks apart. Accuracy of the in vitro diagnosis was also assessed by in vivo anesthetic challenge. Of all muscle bundles from MH-susceptible swine, 65% reacted positively to 3% halothane and 70% to 2 mM caffeine. Only 35% had a positive caffeine-specific concentration, and 25% developed an increase in baseline tension greater than or equal to 7% at 2 mM caffeine. However, when only the most positive response to 3% halothane or to 2 mM caffeine was used (a minimum of three fresh muscle strips is recommended), these two tests were highly sensitive and specific. In control swine one of 30 muscle bundles reacted positively to 3% halothane. A positive caffeine-specific concentration developed in one of 25 control muscle bundles exposed to caffeine. The variability in the results of these tests mandated that at least three muscle bundles be used for each test. Nonviable muscle bundles could not be relied upon to provide accurate results. In this porcine model, MH susceptibility could be detected by performing the Caffeine Halothane Contracture Test (CHCT) according to the guidelines of the North American MH Group. However, only the 3% halothane test and the response to 2 mM caffeine produced adequate diagnostic results in this breed of swine.

Effect of platelet activating factor (PAF) on blood flow distribution in the spontaneously hypertensive rat.

A dose-dependent decrease in mean arterial blood pressure was produced in spontaneously hypertensive rats by intravenous PAF infusion. Heart rate was monitored, while cardiac index and regional blood flow were quantitated during maintenance of the PAF-induced hypotension using the radioactive microsphere method. Our results suggest that PAF administration is associated with specific changes in vascular resistance, since estimated blood flow was decreased to certain organs or tissues, but remained unchanged in others. Therefore, the hypotension observed during PAF infusion is dose-dependent, and is contributed to by decreases in vascular resistance in specific organs.

Adipocyte blood flow: influence of age, anatomic location, and dietary manipulation.

Adipocyte blood flow in four distinct adipose tissue depots has been measured in conscious, unrestrained, male Sprague-Dawley rats by using the microsphere technique together with cellularity determinations. Blood flow was determined in young rats (90 days old, 387 g mean body wt), spontaneously obese rats (450 days old, 713 g mean body wt), and long-term calorically restricted rats (450 days old, 390 g mean body wt), therefore allowing the comparison of the relative effects of age and fat mass on adipose tissue blood flow. Results of these experiments indicate that while cardiac index remained constant, cardiac output increased in only the obese group, concomitant with increased body fat mass. Spontaneously obese rats exhibited increased adipose tissue depot weight, fat cell lipid, and fat cell size compared with young and restricted groups. Despite significant differences in cell volume, blood flow per cell was remarkably similar between young and obese rats. Long-term caloric restriction, however, was associated with decreased flow per cell. Interdepot comparisons of flow per unit surface area (mm2) or per unit volume (pl) indicate that mesenteric cells receive significantly more blood than cells of the other depots. Our results suggest that adipocyte blood flow is dependent in part on anatomic location, may be further influenced by age or dietary manipulation, and is not a limiting factor in the enlargement of adipocytes during the development of spontaneous obesity.

Effect of caloric restriction on cardiac reactivity and beta-adrenoceptor concentration.

The effect of a 21-day program of caloric restriction on cardiac reactivity and beta-adrenoceptor number was investigated in male Sprague-Dawley rats. Rats on the restricted diet (Restricted) exhibited significant decreases in body weight, epididymal fat pad, and retroperitoneal fat pad weight as well as the percent of body fat represented by these adipose tissue depots when compared with rats fed ad libitum (Fed). Fed rats exhibited significantly increased total heart weight and total heart protein, but the percent cardiac protein and ratio of heart weight to body weight were similar in Fed and Restricted rats. Isolated atria from Fed and Restricted rats developed similar chronotropic and inotropic responses over a range of isoproterenol concentrations. Although total beta-adrenoceptor number (fmol/heart) was greater in Fed rats, the concentration of beta-adrenoceptors (fmol/mg protein) was remarkably similar regardless of the dietary regimen. Therefore, despite significant decreases in body weight, body fat, and heart weight, the myocardium of Restricted rats maintained the capability of responding to isoproterenol as that of Fed rats, the mechanism of which is at least partially mediated through maintenance of beta-adrenoceptor concentration.