Influence of Carbon Nanoparticle Addition (and Impurities) on Selective Laser Melting of Pure Copper.

The addition of 0.1 wt % carbon nanoparticles significantly improved the optical absorption and flowability of gas-atomized copper powder. This facilitated selective laser melting (SLM) by reducing the required laser energy density to obtain 98% dense parts. Moreover, the carbon addition led to an in situ de-oxidation of the copper parts during the SLM process. The properties of the as-built copper parts were limited to a tensile strength of 125 MPa, a ductility of 3%, and an electrical conductivity of 22.7 × 106 S/m, despite the advantageous effect of carbon on the powder characteristics and SLM behavior. The modest mechanical properties were associated with the segregation of carbon nanoparticles and other impurities, such as phosphorus and oxygen along grain boundaries of epitaxially grown grains. Whereas, the low electrical conductivity was mainly attributed to the phosphorus impurity in solid-solution with copper.

Right ventricle outflow tract prestenting: In vitro testing of rigidity and corrosion properties.

BACKGROUND: The aim of this study was to assess the resistance to compression (stiffness) of frequently used stents for right ventricular outflow tract prestenting. In addition, to assess the corrosion potential when different types of stent alloys come into contact with each other. METHOD: Different stents were tested in vitro in various combinations at specialized metallurgic laboratories. A bench compression test was used to assess resistance to compression of singular and joined combinations of stents. Corrosion was evaluated by standardized electrochemical galvanic tests in physiological solutions at 37°C. Single stents and combinations of stents were evaluated over a period of 4-12 weeks. RESULTS: Relative stiffness of the stents Optimus/Andrastent XXL/Intrastent LD Max/8zig Cheatham-Platinum, expressed as load per length to deform the stent for 1 mm at 22 mm was 100/104/161/190. Adding additional stents to a single stent significantly strengthened the joined couples (P < 0.001). The lowest galvanic corrosion rates (about 0.000001 mm/year) were observed for the joined CP-Andrastent, Andra-Sapien, and Andra-SapienXT. The corrosion rate for coupled CP-Sapien and CP-SapienXT was somewhat higher (about 0.000003 mm/year). The materials with the highest corrosion rates resulted in material losses of, respectively, 17 and 24 µg/year, which is negligible over a lifetime. CONCLUSION: Adding stents to a single stent significantly increases stiffness which will reduce the risk of metal fatigue failure. Corrosion of individual stents or stent combinations occurs, but is negligible over a human lifetime with low risk of biological effects. No mechanical integrity problems are thus expected as there is only 0.3% of the initial diameter of the struts of a stent that will be lost as a consequence of corrosion after 100 years.

Solubility increases associated with crystalline drug nanoparticles: methodologies and significance.

In this manuscript, the determination of solubility of crystalline drug nanosuspensions by a range of methods is critically investigated. As the determinations of solubility were performed in the presence of the solubilizing nanosuspension stabilizer d-α-tocopherol polyethylene glycol 1000 succinate (TPGS), the potential effects of this excipient on the measurements were studied first. Solubility data of nanosuspensions of itraconazole, loviride, phenytoin and naproxen were generated using different methodologies. Data obtained using separation-based methodologies (centrifugation, filtration and ultracentrifugation) proved to be of limited use, due to poor nanoparticle separation efficiencies and/or significant adsorption of TPGS onto the nanoparticle surfaces. Light scattering and turbidity were found to be more suitable for the determination of nanosuspension solubility. The obtained data show that, unlike earlier reports, the solubility increases due to nanosizing are small, with measured increases of only 15%. These solubility increases are in fair agreement with what would be predicted based on the Ostwald-Freundlich equation.

Magnetic field assisted nanoparticle dispersion.

Magnetohydrodynamic nanoparticle dispersion is an energy efficient method to deaggregate nanoparticles, combining hydrodynamic forces of turbulent flow with Lorentz forces generated by a magnetic field.

Evaluation of the formulation of solid dispersions by co-spray drying itraconazole with Inutec SP1, a polymeric surfactant, in combination with PVPVA 64.

In order to improve the in vitro performance and stability of co-spray-dried itraconazole/Inutec SP1 systems, the influence of adding PVPVA 64, a polymer that is compatible with itraconazole, was evaluated. Dissolution tests were carried out on several itraconazole/PVPVA 64/Inutec SP1 compositions and spray-dried itraconazole/PVPVA 64 powders were used as references. The physicochemical properties of the samples were assessed with modulated temperature differential scanning calorimetry (MDSC), X-ray powder diffraction (XRD) and environmental scanning electron microscopy (ESEM). Physicochemical analysis revealed that there is no interaction between itraconazole and Inutec SP1 and that sufficient amount of PVPVA 64 is required to keep the drug molecularly dispersed. The improvement of the ternary solid dispersions over the binary solid dispersions was composition dependent. On one hand the increased drug/PVPVA 64 ratio in the ternary systems slowed dissolution down, on the other hand this was compensated by the solubilizing power of Inutec SP1.