Circular economy approach: Nutrient recovery and economical struvite production from wastewater sources by using modified biochars.

The enrichment of phosphorus (P) and nitrogen (N) in aquatic systems can cause eutrophication. Moreover, P rocks may become exhausted in the next 100 years. A slow-release fertilizer called struvite (MgNH4PO4.6H2O) can reduce surface runoff. However, the high cost of raw material or chemicals is a bottleneck in their economical production. Therefore, incinerated sewage sludge ash, food wastewater, and bittern were combined as the sources of P, N, and Mg, respectively. Sawdust biochar was used to enhance the adsorptive recovery of nutrients. First, recovery kinetics was studied by comparing bittern-impregnated biochar (BtB) with the Mg-impregnated biochar (MgB). Subsequently, the synergistic physical and chemical interactions were observed for P and N recovery. Almost complete PO43-P recoveries were achieved within 10 min for both biochars. However, NH4+-N recovery was stable after 2 h, with 26% recovery by MgB and 20% recovery by BtB. Biochars activated with steam (steam-activated biochar) and KOH (KOH-activated biochar) gave superior activities to those of unactivated biochars and activated carbon (AC) nutrient recovery and struvite purity. Moreover, the activated biochars showed a lower risk of surface runoff, similar to that of AC. Therefore, activated biochars can be used as an alternative to AC for economical struvite production from a combination of wastewater sources.

Utilizing sludge-based activated carbon for targeted leachate mitigation in wastewater treatment.

Activated carbon (AC) based adsorbents derived from waste sludge were utilized to remediate mixed contaminants in wastewater as an integrated waste-to-resource approach promoting a paradigm shift in management of refuse sludge and wastewater. This review specifically focuses on the remediation of constituents of landfill leachate by sludge-based activated carbon (SBAC). The adsorption effectiveness of SBAC for the exclusion of leachate characters including heavy metals, phenols, dyes, phosphates, and phosphorus were explored with regard to modifiers such as pH, temperature, properties of the adsorbent including functional groups, initial doses of absorbent and adsorbate, and duration of exposure to note the impact of each parameter on the efficiency of adsorption of the sludge adsorbent. Through the works of various researchers, it was noted that the properties of the adsorbent, pH and temperature impact the working of SBACs. The pH of the adsorbent by influencing the functional groups. Temperature was expected to have a paramount effect on the adsorption efficiency of the SBACs. The importance of the regeneration and recycling of the adsorbents as well as their leachability is highlighted. Sludge based activated carbon is recommended as a timely, resource-efficient, and sustainable approach for the remediation of wastewater.

Advancements in TiO2-based photocatalysis for environmental remediation: Strategies for enhancing visible-light-driven activity.

Researchers have focused on efficient techniques for degrading hazardous organic pollutants due to their negative impacts on ecological systems, necessitating immediate remediation. Specifically, TiO2-based photocatalysts, a wide-bandgap semiconductor material, have been extensively studied for their application in environmental remediation. However, the extensive band gap energy and speedy reattachment of electron (e-) and hole (h+) pairs in bare TiO2 are considered major disadvantages for photocatalysis. This review extensively focuses on the combination of semiconducting photocatalysts for commercial outcomes to develop efficient heterojunctions with high photocatalytic activity by minimizing the e-/h+ recombination rate. The improved activity of these heterojunctions is due to their greater surface area, rich active sites, narrow band gap, and high light-harvesting tendency. In this context, strategies for increasing visible light activity, including doping with metals and non-metals, surface modifications, morphology control, composite formation, heterojunction formation, bandgap engineering, surface plasmon resonance, and optimizing reaction conditions are discussed. Furthermore, this review critically assesses the latest developments in TiO2 photocatalysts for the efficient decomposition of various organic contaminants from wastewater, such as pharmaceutical waste, dyes, pesticides, aromatic hydrocarbons, and halo compounds. This review implies that doping is an effective, economical, and simple process for TiO2 nanostructures and that a heterogeneous photocatalytic mechanism is an eco-friendly substitute for the removal of various pollutants. This review provides valuable insights for researchers involved in the development of efficient photocatalysts for environmental remediation.

Production of light olefins and monocyclic aromatic hydrocarbons from the pyrolysis of waste plastic straws over high-silica zeolite-based catalysts.

Owing to the ever-increasing generation of plastic waste, the need to develop environmentally friendly disposal methods has increased. This study explored the potential of waste plastic straw to generate valuable light olefins and monocyclic aromatic hydrocarbons (MAHs) via catalytic pyrolysis using high-silica zeolite-based catalysts. HZSM-5 (SiO2/Al2O3:200) exhibited superior performance, yielding more light olefins (49.8 wt%) and a higher MAH content than Hbeta (300). This was attributed to the increased acidity and proper shape selectivity. HZSM-5 displayed better coking resistance (0.7 wt%) than Hbeta (4.4 wt%) by impeding secondary reactions, limiting coke precursor formation. The use of HZSM-5 (80) resulted in higher MAHs and lower light olefins than HZSM-5 (200) because of its higher acidity. Incorporation of Co into HZSM-5 (200) marginally lowered light olefin yield (to 44.0 wt%) while notably enhancing MAH production and boosting propene selectivity within the olefin composition. These observations are attributed to the well-balanced coexistence of Lewis and Brønsted acid sites, which stimulated the carbonium ion mechanism and induced H-transfer, cyclization, Diels-alder, and dehydrogenation reactions. The catalytic pyrolysis of plastic straw over high-silica and metal-loaded HZSM-5 catalysts has been suggested as an efficient and sustainable method for transforming plastic waste materials into valuable light olefins and MAHs.

Investigating catalytic oxidative desulfurization of model fuel using hollow PW12/TiO2@MgCO3 and performance optimization via box-behnken design.

A facile and eco-friendly synthesis of PW12/TiO2@MgCO3 hollow tubes (PW12·âˆ¼· H3[PW12O40] = polyoxometalate) using a soluble and reusable MgCO3·3H2O micro-rods template was reported for the first time. The resultant hollow tubes were characterized by Fourier transform infrared spectroscopy (FT-IR), UV-visible spectroscopy, powder X-ray diffraction (PXRD), energy-dispersive X-ray spectroscopy (EDX), and scanning electron microscopy (SEM), which indicated that the [PW12O40]3- structure remained intact within the hollow tubes. Furthermore, the specific surface area (88.982 m2/g) and average pore size (2.6 nm) of the PW12/TiO2@MgCO3 hollow tubes were calculated using the Brunauer-Emmett-Teller (BET) analysis. This study explored the catalytic performance of PW12/TiO2@MgCO3 hollow tubes using a three-level Box-Behnken design (BBD), through which optimization curves were designed. The desulfurization of model fuel using hollow tubes was optimally performed when the catalyst dose, time, temperature, and oxidant/sulfur (O/S) were 20-80 gm, 80-120 min, 25-80 °C and 3-8 molar ratio, respectively. These results were further processed, and the experiments were replicated twenty-nine times using a model based on two quadratic polynomials to create a response surface methodology (RSM). This permits a mathematical correlation linking the desulfurization and experimental parameters. The optimal performance of reaction mixture was evaluated to be 80 mg for catalyst concentration, 25 °C of temperature, reaction time of 100 min, and 5.5 for oxidant/sulfur molar ratio from 20 mL of octane simulation oil containing 350 ppm dibenzothiophene (DBT). The predicted desulfurization rate of the model fuel under these optimal conditions was 95.3%. The correspondence between the experimental results and predicted values was verified based on regression analysis, with an R2 value greater than 0.99. These hollow tubes could be used for their desulfurization properties ten times a row without significantly reducing catalytic activity.

Porous Ag3VO4/KIT-6 composite: Synthesis, characterization and enhanced photocatalytic performance for degradation of Congo Red.

Novel Ag3VO4/KIT-6 nanocomposite photocatalyst has been successfully fabricated by a newly-designed simple hard-template induction process, in which the particles of Ag3VO4 were grown on the KIT-6 surface and inside the porous framework of the silica matrix. The developed porous framework nanocomposite was characterized by several techniques including N2-Physiosorption analysis. The obtained nanocomposite revealed a high surface area (273.86 m2/g) along with the possession of monoclinic Ag3VO4, which is highly responsive to visible light (with distinct intensity at about 700 nm). The UV-Vis DRS reveals that the Ag3VO4/KIT-6 photocatalyst bears a bandgap of 2.29 eV which confirms that the material has a good visible light response. The synthesized nanocomposite was tested for its superior physicochemical properties by evaluating its degradation efficiency for Congo Red (CR). The novel composite exhibited superior degradation capability of CR, reaching up to 96.49%, which was around three times the pure Ag3VO4. The detailed kinetic study revealed that the as-prepared material followed a pseudo first order kinetic model for the CR degradation. The study includes a comprehensive parametric study for the formulation of the optimized reaction conditions for photocatalytic reactions. The commercial applicability of the composite material was investigated by a regeneration and recyclability test, which revealed extraordinary results. Furthermore, the possible degradation pathway for CR was also proposed.

Photocatalytic degradation of industrial dye using hybrid filler impregnated poly-sulfone membrane and optimizing the catalytic performance using Box-Behnken design.

Mixed Matrix Membranes have gained significant attention over the past few years due to their diverse applications, unique hybrid inorganic filler and polymeric properties. In this article, the impregnation of nano-hybrid filler (polyoxometalates (∼POMs) encapsulated into the metal-organic framework (MOF) âˆ¼ PMOF) on the polysulfone membrane (∼PSF) was done, resulting in a mix matrix membrane (∼PMOF@PSF). The developed structure was characterized by Fourier transform infrared (FT-IR), powder X-ray diffraction (PXRD), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and transmission electron microscopes (TEM). The results confirmed that the nano-hybrid filler was successfully fabricated on the surface of PSF. Different loading ratios of nano-hybrid filler (5%, 10%, 20%, 30%, and 40%) were used for impregnation. The study's objective was to enhance catalytic performance using optimization curves designed using a three-level Box-Behnken Design (BBD) simulation. The photodegradation of Methylene Blue (∼MB) was studied against PMOF@PSF30% and was found to perform optimally when the concentration of catalyst, time of degradation, and temperature were 0.05-0.15 gm, 40-120 min, and 30-70 °C respectively. These experiments were replicated 15 times, and obtained results were further processed using a two-quadratic polynomial model to develop response surface methodology (RSM), which allowed for a functional relationship between the decolorization and experimental parameters. The optimal performance of the reaction mixture was calculated to be 0.15 gm for concentration, 70 °C for temperature, with an 80 min reaction time. Under these optimal conditions, the predicted decolorization of MB was 98.09%. Regression analysis with R2 > 0.99 verified the fit of experimental results with predicted values. The PMOF@PSF PSF30% demonstrated excellent reusability as its dye degradation properties were significantly unaffected after ten cycles.

Mesoporous LaVO4/MCM-48 nanocomposite with visible-light-driven photocatalytic degradation of phenol in wastewater.

Dearomatization through photocatalytic oxidation is a swiftly rising phenolic compounds removal technology that works at trifling operations requirements with a special emphasis on the generation of nontoxic products. The study aims to develop a LaVO4/MCM-48 nanocomposite that was prepared via a hydrothermally approach assisting the employment of an MCM-48 matrix, which was then utilized for phenol degradation processes. Various techniques including UV-Vis DRS, FTIR, PL, Raman, TEM, and BET analyses are employed to characterize the developed photocatalyst. The developed photocatalyst presented remarkable characteristics, especially increased light photon utilization, and reduced recombination rate leading to enhanced visible-light-driven photodegradation performance owing to the improved specific surface area, specific porosities, and <2 eV narrow energy bandgap. The LaVO4/MCM-48 nanocomposite was experienced on aqueous phenol solution having 20 mg/L concentration under visible-light exposure, demonstrating exceptional performance in photodegradation up to 99.28%, comparatively higher than pure LaVO4. The conducted kinetic measurements revealed good accordance with pseudo first-order. A possible reaction mechanism for photocatalytic degradation was also predicted. The as-synthesized LaVO4/MCM-48 nanocomposite presented excellent stability and recyclability.

A review on activated carbon modifications for the treatment of wastewater containing anionic dyes.

Polluted water resources, particularly those polluted with industrial effluents' dyes, are carcinogenic and hence pose a severe threat to sustainable and longstanding worldwide development. Meanwhile, adsorption is a promising process for polluted/wastewater treatment. In particular, activated carbon (AC) is popular among various wastewater treatment adsorbents, especially in the organic contaminants' remediation in wastewater. Hence, the AC's synthesis from degradable and non-degradable resources, the carbon activation involved in the AC synthesis, and the AC's modification to cutting-edge and effective materials have been modern-research targets in recent years. Likewise, the main research focuses worldwide have been the salient AC characteristics, such as its surface chemistry, porosity, and enhanced surface area. Notably, various modified-AC synthesis methods have been employed to enhance the AC's potential for improved contaminants-removal. Hence, we critically analyze the different modified ACs (with enhanced (surface) functional groups and textural properties) of their capacity to remove different-natured anionic dyes in wastewater. We also discuss the corresponding AC modification techniques, the factors affecting the AC properties, and the modifying agents' influence on the AC's morphological/adsorptive properties. Finally, the AC research of future interest has been proposed by identifying the current AC research gaps, especially related to the AC's application in wastewater treatment.

Conversion of biomass blends (walnut shell and pearl millet) for the production of solid biofuel via torrefaction under different conditions.

The torrefaction of lignocellulose biomass was conducted to produce biochar with properties compatible with coal. Two lignocellulose biomasses, pearl millet (PM) and walnut shell (WS), were torrefied at different process temperatures (230-300 °C), residence times (30-90 min), and different compositional biomass blends to improve the characteristics of the biochar product. The resulting biochar product exhibited favorable changes in their properties. The pure biomasses and their blends obtained a high biochar yield (41-91%). The gross calorific value (GCV) ranged from 22 to 27 MJ/kg, showing an increase of 22-59% compared to the raw biomass. The torrefaction temperature had the most notable effect on the biochar quantity and quality. The biochar samples obtained from the torrefaction of different blends showed a higher GCV and other physicochemical characteristics than the pure biomasses. Scanning electron microscopy showed that these products might also be used for other applications.

Catalytic cracking of polystyrene pyrolysis oil: Effect of Nb2O5 and NiO/Nb2O5 catalyst on the liquid product composition.

The catalytic cracking of polystyrene pyrolysis oil was investigated over a Nb2O5 and a NiO/Nb2O5 catalyst in a fixed bed reactor. First, the pyrolysis of two different polystyrene feedstock (polystyrene foam and polystyrene pellet) was carried out in a semi-batch reactor, and the resulting polystyrene pellets pyrolysis oil was selected for catalytic cracking reaction because of its high liquid yield (85%). Catalytic cracking experiments were then performed at different temperatures (350-500 °C) using Nb2O5 or NiO/Nb2O5 catalyst. Gas chromatography-mass spectrometry analysis of liquid product obtained from the catalytic cracking process showed that the dimers in the pyrolysis oil were converted to monomers during the catalytic cracking process. The catalytic cracking results also showed that the NiO/Nb2O5 catalyst (having slightly higher acidic sites) had slightly higher activity for monomer conversion than the Nb2O5 catalyst (having less acidic sites). X-ray diffraction, transmission electron microscopy, pyridine Fourier transform infrared spectroscopy, NH3 Temperature Programmed Desorption and X-ray photoelectron spectroscopy were used to characterize the catalyst. The highest catalytic cracking activity was observed at 400 °C with the Nb2O5 catalyst with 4% toluene, 6% ethylbenzene, approximately 50% styrene, 13% α-methyl styrene, and only 6% of dimers in the liquid oil. The increase in temperature positively affected the yield of gases during catalytic cracking process.

Systematic Assessment of Visible-Light-Driven Microspherical V2O5 Photocatalyst for the Removal of Hazardous Organosulfur Compounds from Diesel.

The organosulfur compounds present in liquid fuels are hazardous for health, asset, and the environment. The photocatalytic desulfurization technique works at ordinary conditions and removes the requirement of hydrogen, as it is an expensive gas, highly explosive, with a broader flammability range and is declared the most hazardous gas within a petroleum refinery, with respect to flammability. The projected work is based on the synthesis of V2O5 microspheres for photocatalytic oxidation for the straight-run diesel (SRD) and diesel oil blend (DOB). The physicochemical properties of V2O5 microspheres were examined by FT-IR, Raman, UV-vis DRS, SEM, and Photoluminescence evaluations. The as-synthesized photocatalyst presented a trivial unit size, a narrow bandgap, appropriate light-capturing capability, and sufficient active sites. The desulfurization study discovered that the anticipated technique is substantial in desulfurizing DOB up to 37% in 180 min using methanol as an interfacing agent. Furthermore, the outcome of employing a range of polar interfacing solvents was examined, and the 2-ethoxyethanol elevated the desulfurization degree up to 51.3%. However, the anticipated technology is constrained for its application in sulfur removal from SRD. Additionally, the mechanism for a photocatalytic reaction was seen in strong agreement with pseudo-first-order kinetics. The investigated photocatalyst exhibited a compromised recyclability and regeneration tendency.

A comprehensive numerical design of firefighting systems for onshore petroleum installations.

Petroleum facilities containing welded steel bulk flammable liquid product storage tanks possess sundry fire hazards inherent to the facility. These installations urgently require indigenous efficient firefighting systems. So, the efficient design of firewater and firefighting foam system is dynamic in controlling fire-related emergencies. The paper deals with the in-depth conceptualization of the design and analysis of firefighting systems for a typical petroleum handling, processing and storage facility in compliance with international standards. The study is aimed to formulate the elementary technique for designing an optimized firefighting system. The proposed objective was achieved by considering an ideal tank farm site that is most commonly located in a range of terminal stations, pumping stations, petroleum refineries, well sites, etc. Sufficient illumination was enumerated on the standardized classification of the liquid fuel product with respect their flammability range. Special guidelines regarding firefighting system design basis were defined and an optimized firefighting and foam system design was developed. Moreover, sufficient limitations that must be considered during the firefighting of huge tank fires are discussed. This comprehensive numerical design philosophy offers a simple and wide-ranging guide to industrial practitioners by formulating the principles for industrial firefighting system design.

KIT-6 induced mesostructured TiO2 for photocatalytic degradation of methyl blue.

In this study, titania/silica nanocomposite and mesoporous TiO2 (m-TiO2) photocatalysts are developed by KIT-6 template via a sol-gel approach. The synthesized photocatalysts are characterized by XRD, EDX, SEM, Raman, PL, and UV-vis DRS analysis techniques. The as-synthesized series revealed a high surface area, smaller size, a greater number of accessible active sites, and enhanced light-harvesting capability. The m-TiO2 photocatalysts' charge recombination capability was curiously inferior to the rest of as-synthesized TiO2/KIT-6 nanocomposite materials. The band-gap of as-synthesized materials were suitable for their activity in UV light irradiations. It was pragmatic that the photocatalytic degradation efficiency of m-TiO2 photocatalysts was superior as compared to that of commercial TiO2 photocatalyst under UV light irradiations, owing to the synergistic outcome of the anatase phase and a greater number of accessible active-sites availability as a result of high surface area. Moreover, the m-TiO2 was critically evaluated by investigating various parameters affecting the photocatalytic degradation reaction of MB including the effect of irradiation time, pH, catalyst dosage, and dye concentration. The m-TiO2, 45wt% composite material and commercial-TiO2 exhibited 99.27, 91.20, and 84.67% degradation of methyl blue in 50 min, respectively. Finally, the m-TiO2 exhibited excellent recyclability with negligible loss of activity performance.

A state-of-the-art review on wastewater treatment techniques: the effectiveness of adsorption method.

The world's water supplies have been contaminated due to large effluents containing toxic pollutants such as dyes, heavy metals, surfactants, personal care products, pesticides, and pharmaceuticals from agricultural, industrial, and municipal resources into water streams. Water contamination and its treatment have emerged out as an escalating challenge globally. Extraordinary efforts have been made to overcome the challenges of wastewater treatment in recent years. Various techniques such as chemical methods like Fenton oxidation and electrochemical oxidation, physical procedures like adsorption and membrane filtration, and several biological techniques have been recognized for the treatment of wastewater. This review communicates insights into recent research developments in different treatment techniques and their applications to eradicate various water contaminants. Research gaps have also been identified regarding multiple strategies for understanding key aspects that are important to pilot-scale or large-scale systems. Based on this review, it can be determined that adsorption is a simple, sustainable, cost-effective, and environmental-friendly technique for wastewater treatment, among all other existing technologies. However, there is a need for further research and development, optimization, and practical implementation of the integrated process for a wide range of applications.

CO2 from waste to resource by developing novel mixed matrix membranes.

Mixed matrix membranes (MMMs) were fabricated by the hydrothermal synthesis of ordered mesoporous KIT-6 type silica and incorporating in polyimide (P84). KIT-6 and MMMs were characterized to evaluate morphology, thermal stability, surface area, pore volume, and other characteristics. SEM images of synthesized MMMs and permeation data of CO2 suggested homogenous dispersion of mesoporous fillers and their adherence to the polymer matrix. The addition of KIT-6 to polymer matrix improved the permeability of CO2 due to the increase in diffusivity through porous particles. The permeability was 3.2 times higher at 30% loading of filler. However, selectivity showed a slight decrease with the increase in filler loadings. The comparison of gas permeation results of KIT-6 with the well-known MCM-41 revealed that KIT-6 based MMMs showed 14% higher permeability than that of MMMs composed of mesoporous MCM-41. The practical commercial viability of synthesized membranes was examined under different operating temperatures and mixed gas feeds. Mesoporous KIT-6 silica is an attractive additive for gas permeability enhancement without compromising the selectivity of MMMs. Graphical abstract.

Silver nanoparticles stabilized in polymer hydrogels for catalytic degradation of azo dyes.

Fabrication of poly-(N-isopropylmethacrylamide-co-methacrylic acid) [p(NMA)] microgels to be utilized as microreactors to synthesize stable Ag nanoparticles for catalytic reductive degradation of dyes has been addressed in this work. Both p(NMA) microgel and Ag-p(NMA) hybrid microgel systems have been analyzed by Fourier transform infra-red and Dynamic light scattering, Ultraviolet-Visible spectroscopy, X-ray diffraction and Transmission electron microscopy. Catalytic activity of Ag-p(NMA) towards reductive degradation of Congo Red (CR), Methyl Orange (MO) and Alizarin Yellow (AY) was investigated under different operating conditions. Spectrophotometry was employed to check the progress of reaction while the rate constant (kapp) value of degradation reaction was determined under various conditions to optimize reaction parameters for rapid and economical degradation of these dyes. An increase in kapp value was observed by increasing feed content of dye up to a certain value that decreases again by further increment in dye concentration which reflects that catalysis follows Langmuir-Hinshelwood mechanism. A gradual increase in the kapp value was also observed with increasing quantity of hybrid microgel used as a catalyst. By comparing kapp values of degradation of aforementioned dyes, it was found that Ag-p(NMA) hybrid microgel gives better activity for MO dye degradation in comparison to catalytic degradation of CR and AY.

Valorization of underutilized waste biomass from invasive species to produce biochar for energy and other value-added applications.

Biochar production from invasive species biomass discarded as waste was studied in a fixed bed reactor pyrolysis system under different temperature conditions for value-added applications. Prior to pyrolysis, the biomass feedstock was characterized by proximate, ultimate, and heating value analyses, while the biomass decomposition behavior was examined by thermogravimetric analysis. The heating values of the feedstock biomass ranged from 18.65 to 20.65 MJ/kg, whereas the volatile matter, fixed carbon, and ash content were 61.54-72.04 wt %, 19.27-26.61 wt % and 1.51-1.86 wt %, respectively. The elemental composition of carbon, hydrogen, and oxygen in the samples was reported to be in the range of 47.41-48.47 wt %, 5.50-5.88 wt % and 46.10-45.18 wt %, respectively, while the nitrogen and sulphur content in the biomass samples were at very low concentrations, making it more useful for valorization from environmental aspects. The biochar yields were reported in the range of 45.36-58.35 wt %, 28.63-44.38 wt % and 22.68-29.42 wt % at a pyrolysis temperature of 400 °C, 500 °C, and 600 °C, respectively. The biochars were characterized from ultimate analysis, heating value, energy densification ratio, energy yield, pH, Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy and energy dispersive X-ray spectrometry (SEM and EDX), to evaluate their potential for value-added applications. The carbon content, heating value, energy densification ratio, and the porosity of the biochars improved with the increase in pyrolysis temperature, while the energy yield, hydrogen, oxygen, and nitrogen content of the biochars decreased. This study revealed the potential of the valorization of underutilized discarded biomass of invasive species via a pyrolysis process to produce biochar for value-added applications.

Carbon Nanotubes Incorporated Z-Scheme Assembly of AgBr/TiO2 for Photocatalytic Hydrogen Production under Visible Light Irradiations.

Photocatalytic H2 production is a promising strategy toward green energy and alternative to carbon-based fuels which are the root cause of global warming and pollution. In this study, carbon nanotubes (CNTs) incorporated Z-scheme assembly of AgBr/TiO2 was developed for photocatalytic H2 production under visible light irradiations. Synthesized photocatalysts were characterized through transmission electron microscope (TEM), X-ray photoelectron spectra (XPS), X-ray diffractometer (XRD), Fourier transform infrared (FTIR), photoluminescence spectra (PL), Brunauer Emmet-Teller(BET), and UV-vis spectroscopy analysis techniques. The composite photocatalysts exhibited a H2 production of 477 ppm which was three-folds higher than that produced by TiO2. The good performance was attributed to the strong interaction of three components and the reduced charge recombination, which was 89 and 56.3 times lower than the TiO2 and AgBr/TiO2. Furthermore, the role of surface acidic and basic groups was assessed and the photocatalytic results demonstrated the importance of surface functional groups. In addition, the composites exhibited stability and reusability for five consecutive cycles of reaction. Thus, improved performance of the photocatalyst was credited to the CNTs as an electron mediator, surface functional groups, higher surface area, enhanced charge separation and extended visible light absorption edge. This work provides new development of Z-scheme photocatalysts for sustainable H2 production.

Mechanical and Thermal Properties of Montmorillonite-Reinforced Polypropylene/Rice Husk Hybrid Nanocomposites.

In recent years, there has been considerable interest in the use of natural fibers as potential reinforcing fillers in polymer composites despite their hydrophilicity, which limits their widespread commercial application. The present study explored the fabrication of nanocomposites by melt mixing, using an internal mixer followed by a compression molding technique, and incorporating rice husk (RH) as a renewable natural filler, montmorillonite (MMT) nanoclay as water-resistant reinforcing nanoparticles, and polypropylene-grafted maleic anhydride (PP-g-MAH) as a compatibilizing agent. To correlate the effect of MMT delamination and MMT/RH dispersion in the composites, the mechanical and thermal properties of the composites were studied. XRD analysis revealed delamination of MMT platelets due to an increase in their interlayer spacing, and SEM micrographs indicated improved dispersion of the filler(s) from the use of compatibilizers. The mechanical properties were improved by the incorporation of MMT into the PP/RH system and the reinforcing effect was remarkable as a result of the use of compatibilizing agent. Prolonged water exposure of the prepared samples decreased their tensile and flexural properties. Interestingly, the maximum decrease was observed for PP/RH composites and the minimum was for MMT-reinforced and PP-g-MAH-compatibilized PP/RH composites. DSC results revealed an increase in crystallinity with the addition of filler(s), while the melting and crystallization temperatures remained unaltered. TGA revealed that MMT addition and its delamination in the composite systems improved the thermal stability of the developed nanocomposites. Overall, we conclude that MMT nanoclay is an effective water-resistant reinforcing nanoparticle that enhances the durability, mechanical properties, and thermal stability of composites.