Synthesis of Binder-Free, Low-Resistant Randomly Orientated Nanorod/Sheet ZnS-MoS2 as Electrode Materials for Portable Energy Storage Applications.

The scientific community needs to conduct research on novel electrodes for portable energy storage (PES) devices like supercapacitors (S-Cs) and lithium-ion batteries (Li-ion-Bs) to overcome energy crises, especially in rural areas where no electrical poles are available. Herein, the nanostructured MoS2 and ZnS-MoS2 E-Ms consisting of nanoparticles/rods/sheets (N-Ps-Rs-Ss) are deposited on hierarchical nickel foam by a homemade chemical vapor deposition (H-M CVD) route. The X-ray diffraction patterns confirm the formation of polycrystalline films growing along various orientations, whereas the field-emission scanning electron microscope analysis confirms the formation of N-Ps-Rs-Ss. The change in structural and microstructural parameters indicates the existence of defects improving the energy storage ability of the deposited ZnS-MoS2@Ni-F electrodes. The specific capacitances of MoS2@Ni-F and ZnS-MoS2@Ni-F electrodes are found to be 1763 and 3565 F/g at 0.5 mV/s and 1451 and 3032 F/g at 1 A/g, respectively. The growing behavior of impedance graphs indicates their capacitive nature; however, the shifting of impedance curves toward y-axis indicates that the increasing diffusion rates due to the formation of nanostructures of ZnS-MoS2 results in low impedance. An excellent energy storage performance, minimum capacity fading, and improved electrical conductivity of the deposited E-Ms are due to the combined contributions of the electrical double layer and pseudocapacitor nature, which is again confirmed by theoretical Dunn's model. The absence of charge transfer resistance and good capacitance retention (95%) even after 10,000 cycles indicates that the deposited E-Ms are better for PES devices like S-Cs and Li-ion-Bs than MoS2 E-Ms. The assembled asymmetric supercapacitor device exhibited the maximum specific capacitance = 996 F/g, energy density = 354-285 W h/kg, power density = 2400-24,000 W/kg, capacitance retention = 95% and Coulombic efficiency = 100% even after a long charging-discharging of 10,000 cycles.

Engineering of the Central Core on DBD-Based Materials with Improved Power-Conversion Efficiency by Using the DFT Approach.

Developing proficient organic solar cells with improved optoelectronic properties is still a matter of concern. In the current study, with an aspiration to boost the optoelectronic properties and proficiency of organic solar cells, seven new small-molecule acceptors (Db1-Db7) are presented by altering the central core of the reference molecule (DBD-4F). The optoelectronic aspects of DBD-4F and Db1-Db7 molecules were explored using the density functional theory (DFT) approach, and solvent-state calculations were assessed utilizing TD-SCF simulations. It was noted that improvement in photovoltaic features was achieved by designing these molecules. The results revealed a bathochromic shift in absorption maxima (λmax) of designed molecules reaching up to 776 nm compared to 736 nm of DBD-4F. Similarly, a narrow band gap, low excitation energy, and reduced binding energy were also observed in newly developed molecules in comparison with the pre-existing DBD-4F molecule. Performance improvement can be indicated by the high light-harvesting efficiency (LHE) of designed molecules (ranging from 0.9992 to 0.9996 eV) compared to the reference having a 0.9991 eV LHE. Db4 and Db5 exhibited surprisingly improved open-circuit voltage (V OC) values up to 1.64 and 1.67 eV and a fill factor of 0.9198 and 0.9210, respectively. Consequently, these newly designed molecules can be considered in the future for practical use in manufacturing OSCs with improved optoelectronic and photovoltaic attributes.

Food authentication, current issues, analytical techniques, and future challenges: A comprehensive review.

Food authentication and contamination are significant concerns, especially for consumers with unique nutritional, cultural, lifestyle, and religious needs. Food authenticity involves identifying food contamination for many purposes, such as adherence to religious beliefs, safeguarding health, and consuming sanitary and organic food products. This review article examines the issues related to food authentication and food fraud in recent periods. Furthermore, the development and innovations in analytical techniques employed to authenticate various food products are comprehensively focused. Food products derived from animals are susceptible to deceptive practices, which can undermine customer confidence and pose potential health hazards due to the transmission of diseases from animals to humans. Therefore, it is necessary to employ suitable and robust analytical techniques for complex and high-risk animal-derived goods, in which molecular biomarker-based (genomics, proteomics, and metabolomics) techniques are covered. Various analytical methods have been employed to ascertain the geographical provenance of food items that exhibit rapid response times, low cost, nondestructiveness, and condensability.

Experimental and ab initio studies of Co-doped ZnO nanophotocatalyst thin films for dye mineralization.

Pristine ZnO and Co-doped ZnO photocatalyst thin films were fabricated on a ceramic substrate by spray pyrolysis. The optical, morphological and structural properties of the fabricated nanophotocatalyst thin films were analyzed using X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray (EDX) spectroscopy and Fourier transform infrared (FTIR) spectroscopy. Operational parameters, including dye concentration, oxidant concentration, irradiation time and pH for dye degradation, were optimized by response surface methodology (RSM). The maximum degradation obtained was 93% under ideal conditions, such as pH 7, 3 h of direct sunlight irradiation, 30 mM concentration of oxidant and 10 ppm concentration of dye (MB). The evaluation of the extent of degradation was done using the UV/visible spectrophotometry technique. The reusability of the fabricated thin film was examined under optimized conditions. Density functional theory (DFT) with the B3LYP/LanL2DZ method was used for the theoretical modelling of the fabricated nanomaterials. The optimized structure, theoretical band gaps, IR spectra and Raman spectra of the fabricated pristine ZnO and Co:ZnO nanophotocatalysts were determined.

Photo-Induced Super-Hydrophilicity of Nano-Calcite @ Polyester Fabric: Enhanced Solar Photocatalytic Activity against Imidacloprid.

The present study is pertinent to photo-induced, hydrophilic, nano-calcite grown onto the mercerized surface of polyester fabric (PF), treated with UV (10-50 min) and visible light (1-5 h) in addition to its photocatalytic application. The wicking method has been employed to select the most hydrophilic sample of fabric upon irradiation. The micrographs obtained by scanning electron microscopy, transmission electron microscopy, and high-resolution transmission electron microscopy indicated the erosions occurring at the surface of nano-calcite after UV light irradiation, maintaining the crystallinity of the photocatalyst. The surface charge has been measured for as-fabricated and irradiated nano-calcite @ PF for the development of high negative zeta potential after UV light irradiation (-24.6 mV). The irradiated nano-calcite @ PF exhibited a significant change in its contact angle, and the wetting property was enhanced to a considerable extent on UV (55.32°) and visible light irradiation (79.00°) in comparison to as-fabricated nano-calcite @ PF (137.54°). The irradiated samples of nano-calcite @ PF delineated the redshift in harvesting of solar spectrum, as revealed by diffuse reflectance spectroscopy comparative spectra. Additionally, the band gap of untreated nano-calcite was found to be 3.5 eV, while UV- and visible light-irradiated PF showed a reduction in band gap up to 2.95 and 3.15 eV upon UV and visible light irradiation. The photocatalytic efficiency of mesoporous nano-calcite was evaluated by photocatalytic degradation of imidacloprid as the probe pollutant. Higher solar photocatalytic degradation of imidacloprid (94.15%) was attained by UV light-irradiated nano-calcite @ PF. The time-resolved photoluminescence study has verified the high photocatalytic activity of UV light-irradiated nano-calcite @ PF for the generation of high concentration of hydroxyl radicals. The highly efficient reusability of a nano-calcite-based solar photocatalytic reactor has been observed for 10 cycles of treatment of imidacloprid bearing wastewater. The enhanced photocatalytic activity of UV light-exposed (20 min), superhydrophilic, nano-calcite @ PF for mineralization of pollutants suggests it to be an efficient solar photocatalyst for environmental applications.

A novel study for producing complexed and encapsulated nutrients at nanometric scale to enhance plant growth.

Complexation of micronutrients with complexing agents reduce undesirable reactions of fertilizers in soil water system. In the form of complex structure nutrients remain available to plants in the useable form. Nanoform fertilizer enhances the surface area of particles and less amount of fertilizer contact with large area of plant roots which reduce fertilizer cost. Controlling release of fertilizer using polymeric material like sodium alginate makes agriculture practices more efficient and cost effective. Several fertilizers and nutrients are used at a large scale to improve crop yields globally and almost more than half goes to waste. Therefore, there is a dire need to improve plant-available nutrients in soil, using feasible, environmentally friendly technologies. In the present research, complexed micronutrients were successfully encapsulated using a novel technique at nanometric scale. The nutrients were complexed with proline and encapsulated using sodium alginate (polymer). Sweet basil was subjected to seven treatments over three months in a moderately controlled environment (25 °C of temperature and 57% of humidity) to study the effects of synthesized complexed micronutrient nano fertilizers. The structural modifications of the complexed micronutrient nanoforms of fertilizers were examined, through X-ray powder diffraction (XRD) and scanning electron microscopy (SEM). The size of manufactured fertilizers was between 1 and 200 nm. Fourier transform infrared (FTIR) spectroscopy stretching vibration peaks at 1600.9 cm-1 (C=O), 3336 cm-1 (N-H) and at 1090.2 cm-1 (N-H in a twisting and rocking) corresponds to the pyrrolidine ring. Gas chromatography-mass spectrometry was used to analyze the chemical makeup of the essential oil of the basil plants. Essential oil yield of basil plants increased from 0.0035 to 0.1226% after treatments. The findings of the present research show that complexation and encapsulation improve crop quality, essential oil yield, and antioxidant potential of basil.

Semiconductor Nanomaterial Photocatalysts for Water-Splitting Hydrogen Production: The Holy Grail of Converting Solar Energy to Fuel.

Nanomaterials have attracted attention for application in photocatalytic hydrogen production because of their beneficial properties such as high specific surface area, attractive morphology, and high light absorption. Furthermore, hydrogen is a clean and green source of energy that may help to resolve the existing energy crisis and increasing environmental pollution caused by the consumption of fossil fuels. Among various hydrogen production methods, photocatalytic water splitting is most significant because it utilizes solar light, a freely available energy source throughout the world, activated via semiconductor nanomaterial catalysts. Various types of photocatalysts are developed for this purpose, including carbon-based and transition-metal-based photocatalysts, and each has its advantages and disadvantages. The present review highlights the basic principle of water splitting and various techniques such as the thermochemical process, electrocatalytic process, and direct solar water splitting to enhance hydrogen production. Moreover, modification strategies such as band gap engineering, semiconductor alloys, and multiphoton photocatalysts have been reviewed. Furthermore, the Z- and S-schemes of heterojunction photocatalysts for water splitting were also reviewed. Ultimately, the strategies for developing efficient, practical, highly efficient, and novel visible-light-harvesting photocatalysts will be discussed, in addition to the challenges that are involved. This review can provide researchers with a reference for the current state of affairs, and may motivate them to develop new materials for hydrogen generation.

Synthesis of nickel nanowires (Ni-NWs) as high ferromagnetic material by electrodeposition technique.

Metallic nanowires (NWs) and their different compounds display incredible prospects for their use in various applications including media storage, sensor and solar cell devices along with the biological drug delivery systems. In this research work, the metallic NWs like nickel nanowires (Ni-NWs) are synthesized successfully by employing electrodeposition process. Anodic aluminum oxide (AAO) templates are employed as a platform with copper metal coating which acts as an active cathode. The synthesized Ni-NWs are examined through various characterization techniques including X-ray diffraction (XRD), scanning electron microscope (SEM) and vibrating sample magnetometer (VSM) to study the crystal structure, surface morphology and magnetic properties, respectively. The XRD analysis shows the development of various diffraction planes like Ni (111), Ni (200), Ni (220) which confirms the formation of polycrystalline nickel NWs. The SEM analysis reveals that the range of diameter and length of nickel NWs are found to be ∼160 to 200 and ∼4 to 11 micron respectively showing high aspect ratio (ranged from ∼200 to 300). The ferromagnetic behavior of Ni-NWs is confirmed by the hysteresis loop carried out for parallel and perpendicular configurations having Hc = 100 and 206 Oe, respectively. The obtained results suggest that the synthesized Ni- NWs may be used for high-density media storage devices.

On-Site Application of Solar-Activated Membrane (Cr-Mn-Doped TiO2@Graphene Oxide) for the Rapid Degradation of Toxic Textile Effluents.

Solar-activated water treatment has become an emerging research field due to its eco-friendly nature and the economic feasibility of green photocatalysis. Herein, we synthesized promising, cost-effective, and ultralong-semiconductor TiO2 nanowires (NW), with the aim to degrade toxic azo dyes. The band gap of TiO2 NW was tuned through transition metals, i.e., chromium (Cr) and manganese (Mn), and narrowed by conjugation with high surface area graphene oxide (GO) sheets. Cr-Mn-doped TiO2 NWs were chemically grafted onto GO nanosheets and polymerized with sodium alginate to form a mesh network with an excellent band gap (2.6 eV), making it most suitable to act as a solar photocatalytic membrane. Cr-Mn-doped TiO2 NW @GO aerogels possess high purity and crystallinity confirmed by Energy Dispersive X-ray spectroscopy and X-ray diffraction pattern. A Cr-Mn-doped TiO2 NW @GO aerogels membrane was tested for the photodegradation of Acid Black 1 (AB 1) dye. The synthesized photocatalytic membrane in the solar photocatalytic reactor at conditions optimized by response surface methodology (statistical model) and upon exposure to solar radiation (within 180 min) degraded 100% (1.44 kg/m3/day) AB 1dye into simpler hydrocarbons, confirmed by the disappearance of dye color and Fourier transform infrared spectroscopy. An 80% reduction in water quality parameters defines Cr-Mn-doped TiO2 NW @GO aerogels as a potential photocatalytic membrane to degrade highly toxic pollutants.

Production of biodiesel from non-edible feedstocks using environment friendly nano-magnetic Fe/SnO catalyst.

Environmental problems associated with chemical catalysts to fulfil an ever-increasing energy demand have led to the search for an alternative environment friendly heterogeneous catalyst. If a catalyst being used in the biodiesel production is not environment friendly, then the environment is being contaminated in another way while trying to avoid pollution caused by burning of fossil fuels. The present study reports the use of nano-magnetic catalyst Fe/SnO supported on feldspar for the transesterification of various non-edible feedstocks oil, including Pongamia pinnata (karanja), Carthamus oxyacantha (wild safflower), Citrullus colocynthis (bitter apple), Sinapis arvensis (wild mustard) and Ricinus communis (castor). The optimized transesterification parameter was oil to methanol ratio (1:5, 1:10, 1:15, 1:20 and 1:25), catalyst amount (0.5, 1, 1.5, 2, 2.5%), temperature (40, 50, 60, 70 and 80 °C), and reaction times (30, 60, 90, 120 and 150 min). The biodiesel yield was found to be more than 97% for all the tested feedstocks with a maximum biodiesel yield of 98.1 ± 0.6% obtained for bitter apple seed oil under optimum conditions (oil to methanol ratio of 1:10, catalyst amount of 1% at 50 °C for 120 min). The catalysts used for transesterification were magnetically extracted after completion of the reaction. Different physico-chemical parameters like pour point, density, cloud point, iodine value, acid value, saponification and cetane number were determined and the quality of all the biodiesel samples were found to be in the standard range (ASTM D6751 and EN 1404). Different techniques like XRD, FTIR, SEM and EDX were used to characterize the prepared nano-magnetic (Fe/SnO/Feldspar) catalyst.

Soy oil and SPI based-oleogels structuring with glycerol monolaurate by emulsion-templated approach: Preparation, characterization and potential application.

In this study, soybean oil-based oleogels were prepared using soy-protein isolate (SPI) and glycerol monolaurate (GML) in an emulsion-template approach. The rheological, texture, microstructure, and oil-retention properties of the obtained oleogels were analyzed. Results showed that the soy oil-based oleogel prepared with 6 wt% GML exhibited high oil loss, low-hardness, and needle-like morphology compared to the soy-oil/SPI-based oleogel. On the other hand, soy oil-based /SPI-based oleogels structured by 3 or 6 wt% GML presented moderate thermal-stability and lowest oil loss than those prepared without GML. Furthermore, SPI-based oleogel containing 6 wt% GML showed highest free fatty acids release (62.07%) with significantly improved elastic modulus and apparent viscosity. Additionally, the obtained oleogels displayed the occurrence of van der Waals interactions and intermolecular hydrogen bonds, presenting enhanced thermal stability. These results contribute to a better understanding of oleogelation-based emulsions for formulating trans-free and low-saturated foodstuffs with desired physical and functional properties.

Construction of a binder-free non-enzymatic glucose sensor based on Cu@Ni core-shell nanoparticles anchored on 3D chiral carbon nanocoils-nickel foam hierarchical scaffold.

Bimetallic nanostructures composited with carbonaceous materials are the potential contenders for quantitative glucose measurement owing to their unique nanostructures, high biomimetic activity, synergistic effects, good conductivity and chemical stability. In the present work, chemical vapors deposition technique has been employed to grow 3D carbon nanocoils (CNCs) with a chiral morphology on hierarchical macroporous nickel foam (NF) to get a CNCs/NF scaffold. Following, bimetallic Cu@Ni core-shell nanoparticles (CSNPs) are effectively coupled with this scaffold through a facile solvothermal route in order to fabricate a binder-free novel Cu@Ni CSNPs/CNCs/NF hybrid nanostructure. The constructed free-standing 3D hierarchical composite electrode guarantees highly efficient glucose redox activity due to core-shell synergistic effects, enhanced electrochemical active surface area, excellent electrochemical stability, improved conductivity with better ion diffusivity and accelerated reaction kinetics. Being a non-enzymatic glucose sensor, this electrode achieves highly swift response time of 0.1 s, ultra-high sensitivity of 6905 µA mM-1 cm-2, low limit of detection of 0.03 µM along with potential selectivity and good storage stability. Moreover, the proposed sensor is also tested successfully for the determination of glucose concentration in human serum samples under good recovery ranging from 96.6 to 102.1 %. The 3D Cu@Ni CSNPs/CNCs/NF composite electrode with unprecedented catalytic performance can be utilized as an ideal biomimetic catalyst in the field of non-enzymatic glucose sensing.

Fabrication, characterization and in vitro digestion of camellia oil body emulsion gels cross-linked by polyphenols.

This study was designed to investigate the formation of camellia oil body (OB) emulsion gels covalently cross-linked by oxidized polyphenols: catechin (OCT), caffeic acid (OCF), chlorogenic acid (OCA), and tannic acid (OTA). The structural characteristics, thermal stabilities, antioxidant activities, rheological properties, and lipid digestion kinetics of the cross-linked OB-polyphenol emulsion gels were studied. The results of free sulfhydryl and amino group contents, FT-IR, fluorescence spectroscopy, surface hydrophobicity and thermal stability analyses confirmed the formation of covalent interactions between polyphenols and OB emulsions. Based on the second-order structural kinetic model, OB emulsion gel cross-linked by OTA had stronger intermolecular interactions and more developed 3-D network structures than those of OCA, OCF and OCT. Furthermore, lipid digestion kinetics showed that the cross-linking of polyphenols with the OBs slowed down the disintegration of protein matrix under gastric conditions, resulting in delay the release of free fatty acid, which was confirmed by CLSM observations.

Investigation of the adsorption properties of gemcitabine anticancer drug with metal-doped boron nitride fullerenes as a drug-delivery carrier: a DFT study.

Anticancer-drug delivery is now becoming a challenging approach for researchers as it allows controlled drug delivery near cancerous cells with minimized generic collection and the avoidance of secondary side effects. Hence in this work, the applications of nanostructures as anticancer drug-delivery carriers were widely investigated to target cancerous tissues. Based on DFT calculations, we investigated the transition metal-doped boron nitride nanostructure as a drug-delivery agent for the gemcitabine drug utilizing the B3LYP/6-31G (d, p) level of theory. In this research, the adsorption energy and electronic parameters of gemcitabine on the interaction with the metal-doped BN nanostructures were studied. It has been observed that metal doping significantly enhances the drug-delivery properties of BN nanostructures. Among the investigated nanostructures, Ni-BN has been found to be the most prominent nanostructure to transport gemcitabine with an elevated value of adsorption energy in both the gas phase (-45.79) and water media (-32.46). The interaction between gemcitabine and BN nanostructures was confirmed through frontier molecular orbitals and stabilization energy analysis. The fractional charge transfer, MEP, NCI, and NBO analyses exposed the charge transfer from drug molecule to the BN nanostructures. Transition density maps and UV-VIS spectra were also plotted to investigate the excited-state properties of the designed complexes. Thus, the present study provides an in-depth interaction mechanism of the gemcitabine drug with BN, which reveals that metal-doped BN nanostructures can be a favorable drug-delivery vehicle for the gemcitabine anticancer drug.

Enhanced Solar Photocatalytic Activity of Thermally Stable I:ZnO/Glass Beads for Reduction of Cr(VI) in Tannery Effluent.

Chromium (VI) in tannery effluent is one of the major environmental concerns for the environmentalists due to the hazardous nature of Cr(VI) ions. To reduce Cr(VI) to Cr(III) as an innocuous moiety, pure and I-doped ZnO was grafted over the etched surface of glass beads by successive ionic layer adsorption and reaction (SILAR). Powdered, pure, and I-doped ZnO scrapped from the surface of glass beads was characterized for crystallinity, morphology, and elemental composition by XRD, SEM, TEM, and EDX. The optical properties of both photocatalysts revealed that owing to optimized iodine doping of ZnO, reduction in the bandgap was observed from 3.3 to 2.9 eV. The crystalline nano-bricks of I:ZnO adhered to glass beads were investigated to have remarkable capability to harvest sunlight in comparison to intrinsic ZnO nanodiscs. The thermal stability of I:ZnO was also found to be much improved due to doping of ZnO. The photocatalytic activities of ZnO/GB and I:ZnO/GB were compared by extent of reduction of Cr(VI) under direct natural sunlight (600-650 KWh/m2). The disappearance of absorbance peaks associated with Cr(VI) after treatment with I:ZnO/GB confirmed higher photocatalytic activity of I:ZnO/GB. The reaction parameters of solar photocatalytic reduction, i.e., initial pH (5-9), initial concentration of Cr(VI) (10-50 ppm), and solar irradiation time (1-5 h) were optimized using response surface methodology. The solar photocatalytic reduction of Cr(VI) to Cr(III) present in real tannery effluent was examined to be 87 and 98%, respectively, by employing ZnO/GB and I:ZnO/GB as solar photocatalysts. The extent of reduction was also confirmed by complexation of Cr(VI) and Cr(III) present in treated and untreated tannery waste with 1, 5-diphenylcarbazide. The results of AAS and UV/vis spectroscopy for the decrease in concentration of Cr also supported the evidence of higher efficiency of I:ZnO/GB for reduction of Cr(VI) in tannery effluent. Reusability of the fabricated photocatalyst was assessed for eight cycles, and magnificent extent of reduction of Cr(VI) indicated its high efficiency. Conclusively, I:ZnO/GB is a potential and cost-effective candidate for Cr(VI) reduction in tannery effluent under natural sunlight.

Preparation and characterization of thermoplastic polyurethanes blended with chitosan and starch processed through extrusion.

The basic aim of the research work is to expand the application range of biomaterials in the field of medical by increasing antibacterial and biocompatible behavior of thermoplastic polyurethanes. Blends of thermoplastic polyurethanes with chitosan and starch were prepared through extrusion process. The effect of polysaccharides (corn starch and chitosan) incorporation in thermoplastic polyurethane matrix and polymers interaction on thermal and morphological aspects was investigated. Possible interaction among chitosan and starch within TPU matrix individually and together in a blend were assessed by Fourier Transform Infrared Spectroscopy (FTIR) and X-ray Diffractometer (XRD). The results indicated that thermoplastic polyurethanes were semi crystalline in nature whereas hydrophilicity of prepared thermoplastic polyurethanes was determined by contact angle. Biological properties endowed that TPU blended with chitosan and starch possessed antibacterial and hemolytic potential. Hence, it can be a suitable candidate for biomedical applications.

Prewetting Induced Hydrophilicity to Augment Photocatalytic Activity of Nanocalcite @ Polyester Fabric.

To eliminate imidacloprid insecticide from wastewater, nanocalcite was grafted onto the surface of pretreated polyester fabric. The process of seeding was followed by the low temperature hydrothermal method for the growth of nanocalcite for the functionalization of fabric. The goal of this study was to improve the hydrophilicity of the nanocalcite photocatalyst that had been grafted onto the surface of polyester fabric (PF) using acidic and basic prewetting techniques. The morphological characteristics, crystalline nature, surface charge density, functional groups of surface-modified nanocalcite @ PF were determined via SEM, XRD, FTIR, and Zeta potential (ZP), respectively. Characterization results critically disclosed surface roughness due to excessive induction of hydroxyl groups, rhombohedral crystal structure, and high charge density (0.721 mS/cm). Moreover, contact angle of nanocalcite @ PF was calculated to be 137.54° while after acidic and basic prewetting, it was reduced to 87.17° and 48.19°. Similarly, bandgap of the as fabricated nanocalcite was found to be 3.5 eV, while basic prewetted PF showed a reduction in band gap (2.9 eV). The solar photocatalytic mineralization of imidacloprid as a probe pollutant was used to assess the improvement in photocatalytic activity of nanocalcite @ PF after prewetting. Response surface methodology was used to statistically optimize the solar exposure time, concentration of the oxidant, and initial pH of the reaction mixture. Maximum solar photocatalytic degradation of the imidacloprid was achieved by basic prewetted nanocalcite @ PF (up to 91.49%), which was superior to acidic prewetted fabric and as-fabricated nanocalcite @ PF. Furthermore, HPLC and FTIR findings further indicated that imidacloprid was decomposed vastly to harmless species by basic prewetted nanocalcite @ PF.

Fabrication of visible light active Mn-doped Bi2WO6-GO/MoS2 heterostructure for enhanced photocatalytic degradation of methylene blue.

The increase in environmental pollution has led to an increased investigation in the development of novel ternary photocatalytic systems for remediation. These photocatalytic systems exhibit superior photocatalytic action for the removal of pollutants because of their visible light active bandgaps. A highly effective visible light active ternary heterojunction was fabricated using a hydrothermal method assisted by ultrasonication. Herein, we report the in situ hydrothermal synthesis of Mn-doped Bi2WO6-GO/ MoS2 photocatalyst, efficiently exhibiting greater photocatalytic activity for the wastewater treatment under solar light. The binary metal sulphide (MoS2) used as a co-catalyst, acted as an electron collector and graphene oxide (GO) as a support material for interfacial electron transfer to and from bismuth tungstate and MoS2. The as-prepared samples were characterized using SEM-EDX, FT-IR, XRD, XPS, BET, PL, and UV-Vis techniques. The bandgap of the novel photocatalyst was found in the visible region (2.2 eV) which helped in suppressing photoinduced electron-hole pairs recombination. The ternary Mn-doped Bi2WO6-GO/MoS2 showed 99% methylene blue removal after 60 minutes of sunlight irradiation at the optimum conditions of pH 8, catalyst dose 50 mg/100ml, and initial MB concentration of 10ppm under sunlight irradiation. The doped ternary heterostructure has proved to be an effective sunlight-active photocatalyst that can be reused without substantial loss in photocatalytic efficiency.

Vertebral Endplate Changes Correlate with Presence of Cartilaginous Endplate in the Herniated Disc Tissue: Factor Predicting Failure of Conservative Treatment

Methods@#Fifty-one discs were obtained from patients undergoing surgery for herniated disc. Their ages ranged from 19-65 years, and 31/51 were male. Pre-surgical T1 and T2 weighted lumbar-spine MRIs were analyzed to observe Pfirrmann grade, VEP defects, herniation type, Modic changes, and high-intensity zones (HIZ) at the affected level. Five-micron thick sections were stained with hematoxylin and eosin, Alcian blue periodic acid–Schiff stain; examined for histological degeneration scores (HDS; 0–15), inflammation (0 [absence]–3 [severe]), and presence of cartilaginous endplate (CEP). Three-micron thick sections were stained with protein-gene-product 9.5 and expression was counted/mm2. Data was analyzed, and p<0.05 was considered to indicate statistical significance. @*Results@#VEP defects, Modic changes, and HIZ were respectively observed in 30/51, 16/51, and 6/51 of the samples. CEP was observed in 26/51 samples and in 23/51 with endplate defects. Discs with adjacent VEP defects showed increased HDS (p<0.001) and inflammation (p<0.001). Discs with adjacent Modic changes also revealed increased HDS (p=0.01). Histological sections with CEP showed increased HDS (p<0.001) and inflammation (p<0.001), and nerve density was significantly positively correlated with HDS (r=0.27, p=0.02). @*Conclusions@#VEP changes can modulate degeneration and inflammation of herniated discs. Presence of these changes is highly predictive of the occurrence of CEP in herniated discs, which leads to slow resorption and persistent clinical symptoms.