Energy conservation of HVAC systems in isolation rooms using heat pipe heat exchangers.

Isolation rooms are crucial in healthcare facilities to prevent the spread of infectious diseases. Infectious diseases can be transmitted to humans from humans or through animals known as zoonoses. With the increase in the number of COVID-19 cases, isolation rooms have become one of the most critical facilities in hospitals. Maintaining the correct temperature and humidity in these isolation rooms is a challenge, considering the heating, ventilation, and air conditioning (HVAC) systems that continuously consume large amounts of energy. With the application of energy conservation methods, the total energy consumption of HVAC systems can be reduced. Many studies have shown that the heat pipe heat exchanger (HPHE) technology can contribute significantly to energy savings using HVAC systems. In this study, the effectiveness of an HPHE on an HVAC system in an isolation room was examined, and the total energy reduction was quantified. The HPHE consisted of two rows with ten heat pipes in each row, arranged in a staggered configuration with fresh air temperature and mass flow variations. The inlet fresh air temperatures varied at 32, 35, 37, and 40 °C and fresh air velocities at 1.2, 1.6, 2.2, and 2.6 m/s. Using a chiller, the inlet fresh air was cooled to a comfortable temperature zone, approximately 24.4-25.2 °C, in the isolation room. Notably, higher velocities decreased the effectiveness of the HPHE. An increase in the flow rate enhanced the system, thereby improving the heat recovery value. The increase in the inlet fresh air temperature from 32 °C, that yielded an energy saving of 1.23 W, to 40 °C, resulted in a further energy saving of 1.85 W. The application of the HPHE in the HVAC system in isolation rooms represents a significant innovation that contributes to a reduction in total energy consumption.

Cinnamon-Nanoparticle-Loaded Macroalgal Nanocomposite Film for Antibacterial Food Packaging Applications.

In addition to environmental concerns, the presence of microorganisms in plastic food packaging can be hazardous to human health. In this work, cinnamon nanoparticles incorporated with red seaweed (Kappaphycus alvarezii) biopolymer films were fabricated using a solvent casting method. Cinnamon was used as a filler to enhance the properties of the films at different concentrations (1, 3, 5, and 7% w/w) by incorporating it into the matrix network. The physico-chemical, thermal, mechanical, and antimicrobial properties of the cinnamon biopolymer films were obtained using dynamic light scattering (DLS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transmission infrared spectroscopy (FT-IR), water contact angle (WCA) measurement, thermogravimetric analysis (TGA), mechanical testing, and antimicrobial testing, respectively. The results showed that the addition of cinnamon nanoparticles to the film improved the morphological, mechanical, thermal, wettability, and antibacterial properties of the nanocomposite films. The cinnamon particles were successfully reduced to nano-sized particles with an average diameter between 1 nm and 100 nm. The hydrophobicity of the film increased as the concentration of cinnamon nanoparticles incorporated into the seaweed matrix increased. The tensile and thermal properties of the cinnamon seaweed biopolymer film were significantly improved with the presence of cinnamon nanoparticles. The biopolymer films exhibited good inhibitory activity at 7% cinnamon nanoparticles against Escherichia coli (E. coli), Staphylococcus aureus (S. aureus), and Salmonella bacteria with inhibition zone diameters of 11.39, 10.27, and 12.46 mm, indicating the effective antimicrobial activity of the biopolymer film. The functional properties of the fabricated biopolymer film were enhanced with the addition of cinnamon nanoparticles.

Coffee Waste Macro-Particle Enhancement in Biopolymer Materials for Edible Packaging.

Plastic pollution has raised interest in biodegradable and sustainable plastic alternatives. For edible food packaging, seaweed biopolymers have been studied for their film-forming properties. In this study, packaging films were developed using the solvent casting technique from natural red seaweed (Kappaphycus alvarezii) and coffee waste product. The physico-chemical and thermal properties of seaweed/coffee biopolymer films was obtained using dynamic light scattering (DLS), scanning electron microscopy (SEM), Fourier transmission irradiation (FT-IR), water contact angle measurement (WCA) and thermogravimetric analysis (TGA). The characterization study was carried out to improve the film's morphological, thermal, and mechanical properties. The average particle size of coffee waste was found to be between 1.106 and 1.281 µm, with a zeta potential value of -27.0 mV indicating the compound's strong negative charge. The SEM analysis revealed that the coffee filler was evenly dispersed in the polymer matrix, improving the film's structural properties. The FT-IR result shows that coffee waste was successfully incorporated over the film matrix with the presence of a N-H bond. The hydrophobic property of the film was enhanced with the incorporation of coffee filler, indicating increased water contact angle compared to the neat film. The tensile properties of the biopolymer film were significantly improved at 4 wt% coffee powder with optimum tensile strength (35.47 MPa) with the addition of coffee waste powder. The incorporation of coffee waste into the seaweed matrix increased the functional properties of the fabricated biopolymer film. Thus, seaweed/coffee biopolymer film has the potential to be used in food packaging and other applications.

Impact of Zinc Oxide Addition on Oil Palm Empty Fruit Bunches Foamed Polymer Composites for Automotive Interior Parts.

The sustainable use of agricultural waste to generate valuable products while minimizing environmental burdens is increasing rapidly. Multiple sources of fibers have been intensively studied concerning their application in various fields and industries. However, few publications have extensively discussed the property's performance of oil palm empty fruit bunches (OPEFB) composites. With main properties similar to composites currently listed for industrial applications, OPEFB is worth listing as a potential composite for industrial applications and non-structural material alternatives. OPEFB-reinforced polymer composites are expected to be applied to automotive interior parts. This study aims to determine the effect of adding zinc oxide (ZnO) and polyurethane on OPEFB-reinforced polymer composites for automotive interior parts. This composite was produced using the hand lay-up method with 70% resin, 15% OPEFB fiber, 15% polyurethane as a blowing agent, and four variations of ZnO at 5%, 10%, 15%, and 20%. The OPEFB particle sizes are 40, 60, 80, and 100, respectively. The composite was examined to determine mechanical, morphology, chemical, and thermal characteristics. It was observed that the addition of 20% ZnO caused ZnO agglomeration, weakening the interfacial bond between OPEFB particles, polyester, polyurethane, and ZnO filler. Overall, the results showed that adding ZnO and polyurethane to the composite increased tensile, compressive, flexural, and impact strength, as well as thermal stability with more significant values up to 160%, 225%, 100%, 100%, and 4.3%, respectively. This result depicted that the best composition was specimens with 15% ZnO and 149 microns OPEFB fibers particle size. It is considered a promising candidate to be applied in automotive interior components.

Enhanced Functional Properties of Bioplastic Films Using Lignin Nanoparticles from Oil Palm-Processing Residue.

The development of bioplastic materials that are biobased and/or degradable is commonly presented as an alleviating alternative, offering sustainable and eco-friendly properties over conventional petroleum-derived plastics. However, the hydrophobicity, water barrier, and antimicrobial properties of bioplastics have hindered their utilization in packaging applications. In this study, lignin nanoparticles (LNPs) with a purification process were used in different loadings as enhancements in a Kappaphycus alvarezii matrix to reduce the hydrophilic nature and improve antibacterial properties of the matrix and compared with unpurified LNPs. The influence of the incorporation of LNPs on functional properties of bioplastic films, such as morphology, surface roughness, structure, hydrophobicity, water barrier, antimicrobial, and biodegradability, was studied and found to be remarkably enhanced. Bioplastic film containing 5% purified LNPs showed the optimum enhancement in almost all of the ultimate performances. The enhancement is related to strong interfacial interaction between the LNPs and matrix, resulting in high compatibility of films. Bioplastic films could have additional advantages and provide breakthroughs in packaging materials for a wide range of applications.

The Role of Typha angustifilia Fiber-Matrix Bonding Parameters on Interfacial Shear Strength Analysis.

The microbond test of natural fibers tends to produce scattered interfacial shear stress (IFSS) values. The sources of this scattering are known, but the roles they play in producing high IFSS scattering remain to be investigated. In this study, a numerical method was used to simulate microbond testing and to examine the experimental parameters in a microbond test of Typha angustifolia fiber/epoxy. Three parameters were considered: fiber diameter, fiber length embedded in the epoxy, and the distance between the vise and the specimen. The geometries were modeled and analyzed by ABAQUS software using its cohesive zone model features. There were two types of contact used in this analysis: tie constraint and surface-to-surface. The results showcased the roles of the following experimental parameters: a larger fiber diameter from a sample increased the IFSS value, a longer embedded length reduced the IFSS value, and a shorter vise-specimen distance increased the IFSS value. The IFSS scattering in the microbond test could have originated from the interaction between these parameters. Of the three parameters, only the vise-specimen distance was found to be able to be reasonably controlled. When the IFSS value was atypically large, fiber diameter and/or embedded length potentially drove the scattering. This study advises further compilation and classification of the role of each experimental parameter in modulating the IFSS value.

Preparation and Characterization of Nanocellulose/Chitosan Aerogel Scaffolds Using Chemical-Free Approach.

Biopolymer-based aerogels are open three-dimensional porous materials that are characterized by outstanding properties, such as a low density, high porosity and high surface area, in addition to their biocompatibility and non-cytotoxicity. Here we fabricated pure and binary blended aerogels from cellulose nanofibers (CNFs) and chitosan (CS), using a chemical-free approach that consists of high-pressure homogenization and freeze-drying. The prepared aerogels showed a different porosity and density, depending on the material and mixing ratio. The porosity and density of the aerogels ranged from 99.1 to 90.8% and from 0.0081 to 0.141 g/cm3, respectively. Pure CNFs aerogel had the highest porosity and lightest density, but it showed poor mechanical properties and a high water absorption capacity. Mixing CS with CNFs significantly enhance the mechanical properties and reduce its water uptake. The two investigated ratios of aerogel blends had superior mechanical and thermal properties over the single-material aerogels, in addition to reduced water uptake and 2-log antibacterial activity. This green fabrication and chemical-free approach could have great potential in the preparation of biopolymeric scaffolds for different biomedical applications, such as tissue-engineering scaffolds.

Functional Properties and Molecular Degradation of Schizostachyum Brachycladum Bamboo Cellulose Nanofibre in PLA-Chitosan Bionanocomposites.

The degradation and mechanical properties of potential polymeric materials used for green manufacturing are significant determinants. In this study, cellulose nanofibre was prepared from Schizostachyum brachycladum bamboo and used as reinforcement in the PLA/chitosan matrix using melt extrusion and compression moulding method. The cellulose nanofibre(CNF) was isolated using supercritical carbon dioxide and high-pressure homogenisation. The isolated CNF was characterised with transmission electron microscopy (TEM), FT-IR, zeta potential and particle size analysis. The mechanical, physical, and degradation properties of the resulting biocomposite were studied with moisture content, density, thickness swelling, tensile, flexural, scanning electron microscopy, thermogravimetry, and biodegradability analysis. The TEM, FT-IR, and particle size results showed successful isolation of cellulose nanofibre using this method. The result showed that the physical, mechanical, and degradation properties of PLA/chitosan/CNF biocomposite were significantly enhanced with cellulose nanofibre. The density, thickness swelling, and moisture content increased with the addition of CNF. Also, tensile strength and modulus; flexural strength and modulus increased; while the elongation reduced. The carbon residue from the thermal degradation and the glass transition temperature of the PLA/chitosan/CNF biocomposite was observed to increase with the addition of CNF. The result showed that the biocomposite has potential for green and sustainable industrial application.