Candida albicans adherence to denture base material: chemical disinfection and the effect of acquired salivary pellicle formation.

PURPOSE: The aim of this study was to evaluate the effect of 1% sodium hypochlorite (H1%) and 4% chlorhexidine gluconate (CG4%) on the adhesion of Candida albicans to denture base acrylic resins, as well as to verify the effect of the acquired salivary pellicle (ASP) formation on this process. MATERIALS AND METHODS: A total of 300 acrylic specimens were immersed in distilled water (control) (n = 100), H1% (n = 100), or CG4% (n = 100) for 30 days. Twenty specimens were used in each experimental period (0, 1, 7, 15, 30 days). At the end of disinfection testing periods, 10 specimens of each group were exposed to human whole saliva to simulate ASP formation, and then all specimens were incubated with C. albicans ATTC 90028. Microorganism adhesion was analyzed by fluorescence microscopy, after staining with Acridine orange. RESULTS: In the 30(th) disinfection cycle in relation to baseline, the H1% or CG4%, without ASP formation, reduced the C. albicans adhesion by approximately 80%; however, with ASP, this reduction after disinfection with H1% was higher (88%). The presence of ASP resulted in higher reduction of adhered fungal cells in comparison to resin without ASP, at the 1(st) H1% or CG4% disinfection cycle, as well as at 30(th) H1% disinfection cycles. CONCLUSIONS: Our results suggest that the presence of saliva might influence the adhesion of C. albicans and improve the effectiveness of methods to reduce fungal adhesion.

Effect of repeated immersion solution cycles on the color stability of denture tooth acrylic resins

OBJECTIVE: Chemical solutions have been widely used for disinfection of dentures, but their effect on color stability of denture tooth acrylic resins after repeated procedures is still unclear. The aim of this in vitro study was to evaluate whether repeated cycles of chemical disinfectants affected the color stability of two denture tooth acrylic resins. MATERIAL AND METHODS: Sixty disc-shaped specimens (40 mm x 3 mm) were fabricated from two different brands (Artiplus and Trilux) of denture tooth acrylic resin. The specimens from each brand (n=30) were randomly divided into 6 groups (n=5) and immersed in the following solutions: distilled water (control group) and 5 disinfecting solutions (1 percent sodium hypochlorite, 2 percent sodium hypochlorite, 5.25 percent sodium hypochlorite, 2 percent glutaraldehyde, and 4 percent chlorhexidine gluconate). Tooth color measurements were made by spectrophotometry. Before disinfection, the initial color of each tooth was recorded. Further color measurements were determined after subjecting the specimens to 7, 21, 30, 45, 60, and 90 immersion cycles in each tested solution. Color differences (ΔE*) were determined using the CIE L*a*b* color system. Data were analyzed using two-way repeated measures analysis of variance (ANOVA) followed by Tukey tests. The significance level was set at 5 percent. RESULTS: There were statistically significant differences in ΔE* among the 5 disinfectants and water during the 90 cycles of immersion for both denture tooth acrylic resins. Distilled water promoted the greatest color change in both denture tooth acrylic resins, nevertheless none of tested disinfectants promoted ΔE* values higher than 1.0 on these acrylic materials during the 90 cycles of disinfection. CONCLUSIONS: Repeated immersion cycles in disinfecting solutions alter ΔE* values, however these values do not compromise the color of the tested denture tooth acrylic resins because they are imperceptible to the human eye.

Effect of repeated immersion solution cycles on the color stability of denture tooth acrylic resins.

OBJECTIVE: Chemical solutions have been widely used for disinfection of dentures, but their effect on color stability of denture tooth acrylic resins after repeated procedures is still unclear. The aim of this in vitro study was to evaluate whether repeated cycles of chemical disinfectants affected the color stability of two denture tooth acrylic resins. MATERIAL AND METHODS: Sixty disc-shaped specimens (40 mm x 3 mm) were fabricated from two different brands (Artiplus and Trilux) of denture tooth acrylic resin. The specimens from each brand (n=30) were randomly divided into 6 groups (n=5) and immersed in the following solutions: distilled water (control group) and 5 disinfecting solutions (1% sodium hypochlorite, 2% sodium hypochlorite, 5.25% sodium hypochlorite, 2% glutaraldehyde, and 4% chlorhexidine gluconate). Tooth color measurements were made by spectrophotometry. Before disinfection, the initial color of each tooth was recorded. Further color measurements were determined after subjecting the specimens to 7, 21, 30, 45, 60, and 90 immersion cycles in each tested solution. Color differences (ΔE*) were determined using the CIE L*a*b* color system. Data were analyzed using two-way repeated measures analysis of variance (ANOVA) followed by Tukey tests. The significance level was set at 5%. RESULTS: There were statistically significant differences in ΔE* among the 5 disinfectants and water during the 90 cycles of immersion for both denture tooth acrylic resins. Distilled water promoted the greatest color change in both denture tooth acrylic resins, nevertheless none of tested disinfectants promoted ΔE* values higher than 1.0 on these acrylic materials during the 90 cycles of disinfection. CONCLUSIONS: Repeated immersion cycles in disinfecting solutions alter ΔE* values, however these values do not compromise the color of the tested denture tooth acrylic resins because they are imperceptible to the human eye.