Recrystallization of Hot-Rolled 2A14 Alloy during Semisolid Temperature Annealing Process.

In this study, in order to provide proper parameters for the preparation of semisolid billets, the semisolid annealing of hot-rolled 2A14 Al alloy was investigated. The microstructure was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) with an X-ray energy dispersive spectrometer (EDS) and electron backscattered diffraction (EBSD), and scanning transmission electron microscopy (STEM). The XRD results showed that, with an increase in temperature, the θ-Al2Cu equilibrium gradually dissolved in the matrix. The EDS results of SEM and STEM showed a coarse θ-Al2Cu phase, ultrafine precipitate Al(MnFeSi) or (Mn, Fe)Al6 phase, and atomic clusters in the microstructure. The EBSD results showed that the recrystallization mechanism was dominated by continuous static recrystallization (CSRX), homogeneous nucleation occurred when the sample was heated to near solidus temperature, and CSRX occurred at a semisolid temperature. In the process of recrystallization, the microtexture changed from the preferred orientation to a random orientation. Various experimental results showed that static recrystallization (SRX) occurred at a semisolid temperature due to the blocking effect of atomic clusters on the dislocation slip, and the Zener drag effect of fine precipitates on low-angle grain boundaries (LAGBs) disappeared with melting at a semisolid temperature.

Effect of Local Pressurization on Microstructure and Mechanical Properties of Aluminum Alloy Flywheel Housing with Complex Shape.

In this work, squeeze casting experiments of flywheel housing components with a large wall thickness difference and a complex shape were carried out with AlSi9Mg aluminum alloy. The defects, microstructures, and mechanical properties under different process parameters were investigated. Furthermore, the local pressurization process was applied to the thick-walled positions to force-feed the cast defects. The mechanical properties and microstructures at these positions were analyzed. The results showed that the surface quality of formed components was good and that local pressurization could effectively reduce the shrinkage cavity and shrinkage porosity in thick walls, but the scope and effect of forced feeding were limited. The optimum process parameters were a pouring temperature of 650 °C, a specific pressure of 48 MPa, a mold temperature of 220 °C, a local pressurization of 800 MPa, and pressure delay times of 15 s (side A) and 17 s (side B). The ultimate tensile strength, yield strength, and elongation of the formed component under validation experiments of the optimum process parameters were 201 MPa, 103 MPa, and 5.1%. Meanwhile, the fine grains of primary α-Al were mainly rosette and equiaxed grains, and the average grain size was about 40 µm. The microstructure of the eutectic silicon was acicular and was prone to segregation under pressure. According to profile morphology, the positions after pressurization were divided into a deformation zone, a direct action zone, and an indirect action zone. The coexistence of as-cast and plastic deformation microstructures was observed. The effect of local pressurization mainly involved a change in the solidification process, plastic deformation, and forced feeding.

Numerical Simulation and Experimental Validation of Squeeze Casting of AlSi9Mg Aluminum Alloy Component with a Large Size.

The squeeze casting process for an AlSi9Mg aluminum alloy flywheel housing component was numerically simulated using the ProCAST software, and orthogonal simulation tests were designed according to the L16 (4) 5 orthogonal test table to investigate the alloy melt flow rule under four factors and four levels each of the pouring temperature, mold temperature, pressure holding time and specific pressure, as well as the distributions of the temperature fields, stress fields and defects. The results showed that the flywheel housing castings in all 16 test groups were fully filled, and the thinner regions solidified more quickly than the thicker regions. Hot spots were predicted at the mounting ports and the convex platform, which could be relieved by adding a local loading device. Due to the different constraints on the cylinder surface and the lower end surface, the solidification was inconsistent, the equivalent stress at the corner junction was larger, and the castings with longer pressure holding time and lower mold temperature had larger average equivalent stress. Shrinkage cavities were mainly predicted at mounting ports, the cylindrical convex platform, the peripheral overflow groove and the corner junctions, and there was also a small defect region at the edge of the upper end face in some test groups.

Effects of Isothermal Temperature and Soaking Time on Water Quenched Microstructure of Nickel-Based Superalloy GH3536 Semi-Solid Billets.

Semi-solid billets of GH3536 alloy were prepared by semi-solid isothermal treatment of wrought superalloy method. GH3536 samples were soaked at several semi-solid temperatures (1350 °C, 1360 °C, 1364 °C, and 1367 °C) for 5-120 min. The effects of temperature and soaking time on the microstructure of GH3536 billets were studied. The results indicated that the microstructure was affected by coalescence mechanism, Ostwald ripening mechanism, and breaking up mechanism. Semi-solid microstructure of GH3536 alloy was composed of spherical solid particles and liquid phases, and the liquid phases affected the microstructure greatly. At 1350 °C, the coalescence mechanism was dominant at the early stage of isothermal treatment, then the Ostwald ripening mechanism played a major role for the longer soaking times. At higher temperatures, the breaking up mechanism occurred to form large irregular grains and small spherical grains. As the heating continued, the Ostwald ripening mechanism was dominant. However, at 1364 °C and 1367 °C, the solid grains had irregular shapes and large sizes when the isothermal time was 120 min. The optimum parameters for the preparation of GH3536 semi-solid billets were: temperature of 1364-1367 °C and soaking time of 60-90 min.