Effect of high-pressure homogenization preparation on mean globule size and large-diameter tail of oil-in-water injectable emulsions.

The effect of different high pressure homogenization energy input parameters on mean diameter droplet size (MDS) and droplets with > 5 µm of lipid injectable emulsions were evaluated. All emulsions were prepared at different water bath temperatures or at different rotation speeds and rotor-stator system times, and using different homogenization pressures and numbers of high-pressure system recirculations. The MDS and polydispersity index (PI) value of the emulsions were determined using the dynamic light scattering (DLS) method, and large-diameter tail assessments were performed using the light-obscuration/single particle optical sensing (LO/SPOS) method. Using 1000 bar homogenization pressure and seven recirculations, the energy input parameters related to the rotor-stator system will not have an effect on the final particle size results. When rotor-stator system energy input parameters are fixed, homogenization pressure and recirculation will affect mean particle size and large diameter droplet. Particle size will decrease with increasing homogenization pressure from 400 bar to 1300 bar when homogenization recirculation is fixed; when the homogenization pressure is fixed at 1000 bar, the particle size of both MDS and percent of fat droplets exceeding 5 µm (PFAT5) will decrease with increasing homogenization recirculations, MDS dropped to 173 nm after five cycles and maintained this level, volume-weighted PFAT5 will drop to 0.038% after three cycles, so the "plateau" of MDS will come up later than that of PFAT5, and the optimal particle size is produced when both of them remained at plateau. Excess homogenization recirculation such as nine times under the 1000 bar may lead to PFAT5 increase to 0.060% rather than a decrease; therefore, the high-pressure homogenization procedure is the key factor affecting the particle size distribution of emulsions. Varying storage conditions (4-25°C) also influenced particle size, especially the PFAT5.

[Analysis and identification of degradation products of buagafuran by high performance liquid chromatography-diode array detection-tandem mass spectrometry].

An HPLC-DAD-MS/MS method was developed for rapid analysis and identification of degradation products of buagafuran. Buagafuran and degradation products were separated on a Zorbax C8 column (5 microm, 4.6 mm x 150 mm) using acetonitrile-water (78 : 22) as mobile phase. The elutes were detected with diode array detector and tandem mass spectrometer via electrospray ionization source in positive ion mode. According to analysis of the retention time, UV spectra and MS, MS/MS data, combined with the possible degradation reaction of buagafuran, the structures of main degradation products were inferred. The results showed that six main degradation products were oxidation or peroxidation productions of buagafuran. Degradation product A was a double bond epoxidation product of buagafuran, degradation products B, C, D and E were the further oxidation products of degradation product A, degradation product F was a peroxidation product of buagafuran. The results indicated that the established method was effective in the rapid identification of the degradation products of buagafuran.

Formulation, characterization and hypersensitivity evaluation of an intravenous emulsion loaded with a paclitaxel-cholesterol complex.

The objective of this paper was to develop a novel Cremophor-free, autoclave stable, intravenous emulsion for paclitaxel (PACE). A paclitaxel-cholesterol complex was used as the drug carrier to improve the solubility of paclitaxel in the oil phase of emulsions. The complex and PACE were prepared by rotary evaporation and high-pressure homogenization, respectively. Effects of oil phases, emulsifiers and pH values on the characteristics of PACE were investigated. PACE was characterized with regard to its appearance, morphology, osmolality, pH value, particle size, zeta potential, encapsulation efficiency and stability. Hypersensitivity was evaluated by guinea pig hypersensitivity reaction. The final formulation was composed of the complex, soybean oil, medium-chain triglyceridel, soybean lecithin, poloxamer 188 and glycerol. The resulting PACE had an encapsulation efficiency of 97.3% with a particle size of 135 nm and a zeta potential of -38.3 mV. Osmolality and pH of the formulation were 383 mOsmol/kg and 4.5, respectively. The formulation survived autoclaving at 115 °C for 30 min and remained stable for at least 12 months at 6 °C. PACE also exhibited a better tolerance than an equal dose of Cremophor-based paclitaxel injection in guinea pigs, as no obvious hypersensitivity reaction was observed. These results suggested that PACE has a great potential for industrial-scale production and clinical applications.