Growth of bulk ß-Ga2O3 crystals from melt without precious-metal crucible by pulling from a cold container.

We report the growth of bulk ß-Ga2O3 crystals based on crystal pulling from a melt using a cold container without employing a precious-metal crucible. Our approach, named oxide crystal growth from cold crucible (OCCC), is a fusion between the skull-melting and Czochralski methods. The absence of an expensive precious-metal crucible makes this a cost-effective crystal growth method, which is a critical factor in the semiconductor industry. An original construction 0.4-0.5 MHz SiC MOSFET transistor generator with power up to 35 kW was used to successfully grow bulk ß-Ga2O3 crystals with diameters up to 46 mm. Also, an original diameter control system by generator frequency change was applied. In this preliminary study, the full width at half maximum of the X-ray rocking curve from the obtained ß-Ga2O3 crystals with diameters ≤ 46 mm was comparable to those of ß-Ga2O3 produced by edge-defined film fed growth. Moreover, as expected, the purity of the obtained crystals was high because only raw material-derived impurities were detected, and contamination from the process, such as insulation and noble metals, was below the detection limit. Our results indicate that the OCCC technique can be used to produce high-purity bulk ß-Ga2O3 single crystalline substrate.

Evaluation of anatomical references for locating the course of the posterior superior alveolar artery for dental implant surgery.

This retrospective cohort study aimed to identify the best anatomical reference for predicting the posterior superior alveolar artery (PSAA) location. Computed tomographic images of 90 maxillary sinuses were evaluated. We studied five references, including the alveolar crest, maxillary sinus floor, zygomatoalveolar crest, hard palate and soft palate, and measured the distances between them and the PSAA. Variations in the distance were evaluated by the standard deviation and coefficient of variation (CV). The zygomatoalveolar crest was an unstable reference, owing to its high standard deviation and CV. The smallest CV was for the distance between the alveolar crest and PSAA, although the distance was smaller in edentulous jaws than dentulous jaws. The distance between the sinus floor and PSAA was larger in male and edentulous patients. The PSAA was detected in 40.0%, 44.4%, 54.4% and 56.7% of the sinus walls at the first and second premolar and the first and second molar positions, respectively. At these tooth positions, the respective heights above the hard palate were 11.2 ± 4.9, 8.2 ± 4.9, 6.2 ± 2.8 and 8.1 ± 2.9 mm. The hard palate was the most stable reference for predicting the location of the PSAA, irrespective of sex, age and dentition.

Candida auris: A pathogen difficult to identify, treat, and eradicate and its characteristics in Japanese strains.

Candida auris is a multidrug-resistant and emergent pathogen that has caused healthcare-associated infection outbreaks. Recently, C. auris has spread worldwide; nevertheless, it was unexpectedly rare before 2009. Based on the molecular epidemiological analysis, C. auris may independently emerge at specific areas at first and recently may be transmitted to other continents. As C. auris cannot be detected using conventional methods, internally transcribed spacers, D1/D2 regions of the 26S rDNA sequencing, and/or matrix-assisted laser desorption ionization time-of-flight mass spectrometry method can be selected as comparatively accessible choices. Thus, detection of C. auris using the conventional method might be underestimated. In Japan, all C. auris strains were isolated from ear specimen and not from invasive mycoses. Japan strains were classified as an East Asian clade under a single clone. Although colonization, virulence, and infection pattern are almost the same as with other Candida species, its antifungal resistance is different. Fluconazole resistance is notably common, but resistance to all three classes of antifungals (azole, polyene, and echinocandin) rarely exists. Once C. auris is detected, screening, emphasis on hand hygiene adherence, use of single-patient room isolation, contact precaution, surveillance, and eradication from the environment and patients are appropriately required for infection control.

Real-time detection and discrimination of visual perception using electrocorticographic signals.

OBJECTIVE: Several neuroimaging studies have demonstrated that the ventral temporal cortex contains specialized regions that process visual stimuli. This study investigated the spatial and temporal dynamics of electrocorticographic (ECoG) responses to different types and colors of visual stimulation that were presented to four human participants, and demonstrated a real-time decoder that detects and discriminates responses to untrained natural images. APPROACH: ECoG signals from the participants were recorded while they were shown colored and greyscale versions of seven types of visual stimuli (images of faces, objects, bodies, line drawings, digits, and kanji and hiragana characters), resulting in 14 classes for discrimination (experiment I). Additionally, a real-time system asynchronously classified ECoG responses to faces, kanji and black screens presented via a monitor (experiment II), or to natural scenes (i.e. the face of an experimenter, natural images of faces and kanji, and a mirror) (experiment III). Outcome measures in all experiments included the discrimination performance across types based on broadband γ activity. MAIN RESULTS: Experiment I demonstrated an offline classification accuracy of 72.9% when discriminating among the seven types (without color separation). Further discrimination of grey versus colored images reached an accuracy of 67.1%. Discriminating all colors and types (14 classes) yielded an accuracy of 52.1%. In experiment II and III, the real-time decoder correctly detected 73.7% responses to face, kanji and black computer stimuli and 74.8% responses to presented natural scenes. SIGNIFICANCE: Seven different types and their color information (either grey or color) could be detected and discriminated using broadband γ activity. Discrimination performance maximized for combined spatial-temporal information. The discrimination of stimulus color information provided the first ECoG-based evidence for color-related population-level cortical broadband γ responses in humans. Stimulus categories can be detected by their ECoG responses in real time within 500 ms with respect to stimulus onset.

Passive functional mapping guides electrical cortical stimulation for efficient determination of eloquent cortex in epilepsy patients.

Electrical cortical stimulation (ECS) is often used in presurgical evaluation procedures for patients suffering from pharmacoresistant epilepsy. Real-time functional mapping (RTFM) is an alternative brain mapping methodology that can accompany traditional functional mapping approaches like ECS. In this paper, we present a combined RTFM/ECS system that aims to exploit the common ground and the advantages of the two procedures for improved time/effort effectiveness, patients' experience and safety. Using the RTFM and ECS data from four patients who suffer epilepsy, we demonstrate that the RTFM-guided ECS procedure hypothetically reduces the number of electrical stimulations necessary for eloquent cortex detection by 40%.

Synergistic Functions of Enzymes Bound to Semiconducting Layers.

Synthesis and cooperative functions of hybrid materials composed of enzyme and semiconducting layers are described in this chapter. The hybrids were produced via a simple physical interaction between the components, that is, electrostatic interaction in an aqueous solution. To form interstratifying enzymes in the galleries, solution pH, which is a key parameter to decide surface potential, should be adjusted appropriately. In other words, enzymes should have an opposite charge when compared to that of the layers at an identical pH. Even though the intercalation slightly reduced enzymatic activity as compared to those of the free enzymes, stability under cruel conditions was drastically improved due to screening effect of semiconducting layers from extrinsic stimuli. In addition, photochemical control of redox enzymes sandwiched between semiconducting layers was accomplished. Light irradiation of the hybrids induced band gap excitation of the layers, and holes produced in the valence band activated the enzymes. It was revealed that the semiconducting layers with magnetic elements might be useful to magnetic application (separation) of enzymes as similar to conventional magnetic beads.

Online control of a humanoid robot through hand movement imagination using CSP and ECoG based features.

Intention recognition through decoding brain activity could lead to a powerful and independent Brain-Computer-Interface (BCI) allowing for intuitive control of devices like robots. A common strategy for realizing such a system is the motor imagery (MI) BCI using electroencephalography (EEG). Changing to invasive recordings like electrocorticography (ECoG) allows extracting very robust features and easy introduction of an idle state, which might simplify the mental task and allow the subject to focus on the environment. Especially for multi-channel recordings like ECoG, common spatial patterns (CSP) provide a powerful tool for feature optimization and dimensionality reduction. This work focuses on an invasive and independent MI BCI that allows triggering from an idle state, and therefore facilitates tele-operation of a humanoid robot. The task was to lift a can with the robot's hand. One subject participated and reached 95.4 % mean online accuracy after six runs of 40 trials. To our knowledge, this is the first online experiment with a MI BCI using CSPs from ECoG signals.

Distinction of individual finger responses in somatosensory cortex using ECoG high-gamma activation mapping.

This study demonstrates the feasibility of high-gamma activity mapping for localization of somatosensory finger areas in the human brain. Identification of functional brain regions is important in surgical planning, such as for resections of epileptic foci or brain tumors. The mapping procedure is done using electrocorticography (ECoG), an invasive technique in which electrical brain signals are acquired from the cortical surface. Two epilepsy patients with implanted electrode grids participated in the study. Data were collected during a vibrotactile finger stimulation paradigm and showed significant cortical activation (p <; 0.001) in the high-gamma range over the contralateral somatosensory cortex. The results are consistent with previous studies that used fMRI in test subjects without implanted electrodes. Therefore, the results suggest that localizing the cortical representations of the fingers in clinical practice using ECoG is feasible, even without the patient's active participation.

Plasmonic bipyramids for fluorescence enhancement and protection against photobleaching.

A great number of studies focus their interest on the photophysical properties of fluorescent hybrid gold nanoparticles for potential applications in biotechnologies such as imaging and/or treatment. Spherical gold nanoparticles are known to quench a chromophore fluorescent signal, when moieties are located in their close vicinity. The use of a polymer spacer on such a system allowed only partial recovery of the dye emission by controlling the surface to dye distance. Gold-based anisotropic sharp nanostructures appear to exhibit more interesting features due to the strong electric field generated at their edges and tips. In this paper, a complete study of hybrid fluorescent bipyramidal-like gold nanostructures is presented. We describe the chemical synthesis of gold bipyramids functionalized with fluorescent water-soluble polymers and their photophysics both in solution and on a single object. We show that the use of a bipyramidal shape instead of a spherical one leads to total recovery of the fluorescence and even to an enhancement of the emission of the dyes by a factor of 1.4.

Rapid and low-invasive functional brain mapping by realtime visualization of high gamma activity for awake craniotomy.

For neurosurgery with an awake craniotomy, the critical issue is to set aside enough time to identify eloquent cortices by electrocortical stimulation (ECS). High gamma activity (HGA) ranging between 80 and 120 Hz on electrocorticogram (ECoG) is assumed to reflect localized cortical processing. In this report, we used realtime HGA mapping and functional magnetic resonance imaging (fMRI) for rapid and reliable identification of motor and language functions. Three patients with intra-axial tumors in their dominant hemisphere underwent preoperative fMRI and lesion resection with an awake craniotomy. All patients showed significant fMRI activation evoked by motor and language tasks. After the craniotomy, we recorded ECoG activity by placing subdural grids directly on the exposed brain surface. Each patient performed motor and language tasks and demonstrated realtime HGA dynamics in hand motor areas and parts of the inferior frontal gyrus. Sensitivity and specificity of HGA mapping were 100% compared to ECS mapping in the frontal lobe, which suggested HGA mapping precisely indicated eloquent cortices. The investigation times of HGA mapping was significantly shorter than that of ECS mapping. Specificities of the motor and language-fMRI, however, did not reach 85%. The results of HGA mapping was mostly consistent with those of ECS mapping, although fMRI tended to overestimate functional areas. This novel technique enables rapid and accurate functional mapping.

Single trial detection of hand poses in human ECoG using CSP based feature extraction.

Decoding brain activity of corresponding highlevel tasks may lead to an independent and intuitively controlled Brain-Computer Interface (BCI). Most of today's BCI research focuses on analyzing the electroencephalogram (EEG) which provides only limited spatial and temporal resolution. Derived electrocorticographic (ECoG) signals allow the investigation of spatially highly focused task-related activation within the high-gamma frequency band, making the discrimination of individual finger movements or complex grasping tasks possible. Common spatial patterns (CSP) are commonly used for BCI systems and provide a powerful tool for feature optimization and dimensionality reduction. This work focused on the discrimination of (i) three complex hand movements, as well as (ii) hand movement and idle state. Two subjects S1 and S2 performed single `open', `peace' and `fist' hand poses in multiple trials. Signals in the high-gamma frequency range between 100 and 500 Hz were spatially filtered based on a CSP algorithm for (i) and (ii). Additionally, a manual feature selection approach was tested for (i). A multi-class linear discriminant analysis (LDA) showed for (i) an error rate of 13.89 % / 7.22 % and 18.42 % / 1.17 % for S1 and S2 using manually / CSP selected features, where for (ii) a two class LDA lead to a classification error of 13.39 % and 2.33 % for S1 and S2, respectively.

Human MCG measurements with a high-sensitivity potassium atomic magnetometer.

Measuring biomagnetic fields, such as magnetocardiograms (MCGs), is important for investigating biological functions. To address to this need, we developed an optically pumped atomic magnetometer. In this study, human MCGs were acquired using a potassium atomic magnetometer without any modulating systems. The sensitivity of the magnetometer is comparable to that of high-T(c) superconducting quantum interference devices (SQUIDs) and is sufficient for acquiring human MCGs. The activity of a human heart estimated from the MCG maps agrees well with that measured with SQUID magnetometers. Thus, our magnetometer produces reliable results, which demonstrate the potential of our atomic magnetometer for biomagnetic measurements.

Down-scattered neutron imaging detector for areal density measurement of inertial confinement fusion.

A custom developed (6)Li glass scintillator (APLF80+3Pr) for down-scattered neutron diagnostics in inertial confinement fusion experiments is presented. (6)Li provides an enhanced sensitivity for down-scattered neutrons in DD fusion and its experimentally observed 5-6 ns response time fulfills the requirement for down-scattered neutron detectors. A time-of-flight detector operating in the current mode using the APLF80+3Pr was designed and its feasibility observing down-scattered neutrons was demonstrated. Furthermore, a prototype design for a down-scattered neutron imaging detector was also demonstrated. This material promises viability as a future down-scattered neutron detector for the National Ignition Facility.

Inferring spatiotemporal network patterns from intracranial EEG data.

OBJECTIVE: The characterization of spatial network dynamics is desirable for a better understanding of seizure physiology. The goal of this work is to develop a computational method for identifying transient spatial patterns from intracranial electroencephalographic (iEEG) data. METHODS: Starting with bivariate synchrony measures, such as phase correlation, a two-step clustering procedure is used to identify statistically significant spatial network patterns, whose temporal evolution can be inferred. We refer to this as the composite synchrony profile (CSP) method. RESULTS: The CSP method was verified with simulated data and evaluated using ictal and interictal recordings from three patients with intractable epilepsy. Application of the CSP method to these clinical iEEG datasets revealed a set of distinct CSPs with topographies consistent with medial temporal/limbic and superior parietal/medial frontal networks thought to be involved in the seizure generation process. CONCLUSIONS: By combining relatively straightforward multivariate signal processing techniques, such as phase synchrony, with clustering and statistical hypothesis testing, the methods we describe may prove useful for network definition and identification. SIGNIFICANCE: The network patterns we observe using the CSP method cannot be inferred from direct visual inspection of the raw time series data, nor are they apparent in voltage-based topographic map sequences.

Effect of tube voltage on image quality in 64-section multidetector 3D CT angiography: Evaluation with a vascular phantom with superimposed bone skull structures.

BACKGROUND AND PURPOSE: Optimal tube voltage and tube current settings are not well established. The purpose of our study was to investigate the image quality on 3D CT angiograms of the brain at various kilovoltage settings by evaluating the depiction of simulated intracranial lesions by using a vascular phantom. MATERIALS AND METHODS: An anthropomorphic vascular phantom with superimposed bone skull structures was designed to simulate various intracranial aneurysms with aneurysmal blebs. We performed CT angiography by using a 64-detector row CT scanner for various effective tube currents with 4 tube voltages of 80, 100, 120, and 135 kV(p). Simulated aneurysm enhancement and image noise were quantified; SNR and CNR were calculated. The depiction of the simulated aneurysms and blebs on 3D CT angiograms obtained with the volume-rendering technique was subjectively assessed. The effective dose was calculated on the basis of a CTDIw. The results of several protocols were compared by using the Student t test. RESULTS: At identical doses levels (CTDIw), the mean SNR and CNR at 100 kV(p) were significantly higher than those at 80, 120, and 135 kV(p); and the mean qualitative image score at 100 kV(p) was significantly superior to those at 80 and 135 kV(p). CONCLUSIONS: Our phantom study suggests that the tube voltage of 100 kV(p) is desirable for cerebral 3D CT angiograms, and the higher or lower kilovoltage settings may result in the degradation in diagnostic image quality.

Signal intensity of the motor cortex on phase-weighted imaging at 3T.

BACKGROUND AND PURPOSE: It is known that the motor cortex shows hypointensity on T2-weighted images in older patients. The goal of this study was to assess the signal intensity of the motor cortices on the phase-weighted imaging performed with a Windows-based software program that we developed ourselves. MATERIALS AND METHODS: All studies were performed at 3T MR imaging. First, the TE for the phase-weighted image was optimized; the best contrast between the motor and other cortices was obtained with a TE of 40 ms. The study population consisted of 45 healthy subjects (23 females, 22 males; mean age, 32.1 years). The signal intensity of the motor cortices was divided into 3 grades by 2 neuroradiologists in comparison with that of the superior frontal cortex (SFC): In grade I, the motor cortex was isointense to the SFC; in grade II, the motor cortex was slightly hypointense to the SFC; and in grade III, the motor cortex was markedly hypointense to the SFC. RESULTS: The motor cortex was classified as either grade II or III in all subjects older than 20 years of age on the phase-weighted images. Even at 10-19 years of age, the grade II or III appearance was found in 14 (88%) of 16 motor cortices (8 subjects) on the phase-weighted images. CONCLUSION: In adolescents, the motor cortex is hypointense to other cerebral cortices on phase-weighted MR imaging, which probably reflects differences in the concentration of nonheme iron and/or in the tissue architecture.

Reversible widespread ischemia after early reperfusion detected by initial diffusion-weighted magnetic resonance imaging.

We herein report the time-related dynamic changes according to the diffusion-weighted image (DWI) findings after a cerebral ischemic attack in a 63-year-old woman. At 2 weeks after undergoing a lower limb amputation due to diabetic atherosclerosis, she experienced a sudden loss of consciousness and right hemiparesis. Magnetic resonance image revealed left frontal and parietal areas with an increased signal on the DWI, and magnetic resonance angiography (MRA) showed the left middle cerebral artery to be occluded at the superior M2 branch. However, on the next day the lesion on DWI, except for the gray matter, was observed to have almost completely resolved, and MRA showed complete recanalization of the left superior M2 branch with diminished clinical symptoms. Although a few cases of reversible DWI-identified lesions have been described in the literature, the occurrence of large, reversed DWI lesions in the middle cerebral artery territory with severe apparent diffusion coefficient decreases, as seen in our case, are exceedingly rare.

Abrasion resistance of titanium nitride coatings formed on titanium by ion-beam-assisted deposition.

To improve the physical properties of the pure titanium surface, thin titanium nitride (TiN) films were deposited by means of ion-beam-assisted deposition. Film structure was confirmed as TiN by X-ray diffraction analysis. Surface hardness and abrasion resistance were significantly improved on TiN-coated specimens. Five combinations of oral hygiene instruments and materials were applied to the specimens as simulations of the oral environment. Treatment with the metal scaler and ultrasonic scaler severely changed the surface features and significantly increased the surface roughness parameters on pure titanium controls, whereas only small scratches and dull undulations were seen on the TiN-coated specimens. Profilometric tracings and scanning electron micrographs demonstrated the improved abrasion resistance of the TiN-coated specimens.

Bonding between resin luting cement and glass infiltrated alumina-reinforced ceramics with silane coupling agent.

The purpose of this study was to evaluate the shear bond strengths of three dual-cured resin luting cements (Linkmax HV, Panavia Fluoro Cement, and RelyX ARC) to glass-infiltrated alumina-reinforced ceramic material and the effect of four silane coupling agents (Clearfil Porcelain Bond, GC Ceramic Primer, Porcelain LinerM, and Tokuso Ceramic Primer) on the bond strength. The two type-shaped of In-Ceram alumina ceramic glass-infiltrated specimens were untreated or treated with one of the four ceramic primers and then cemented together with one of the three dual-cured resin luting cements. Half of the specimens were stored in water at 37 degrees C for 24 h and the other half thermocycled 20,000 times before shear bond strength testing. Surface treatment by all silane coupling agents improved the shear bond strength compared with non-treatment. The specimens treated with Clearfil Porcelain Bond showed significantly greater shear bond strength than any of the other three silane coupling agents regardless of resin luting cements and thermocycling except for the use of Panavia Fluoro Cement at 20,000 thermocycles. When the alumina-reinforced ceramic material was treated with any silane coupling agent except GC Ceramic Primer and cemented with Linkmax HV, no significant differences in bond strength were noted between after water storage and after 20,000 thermocycles. After 20,000 thermocycles, all specimens except for the combined use of Clearfil Porcelain Bond or GC Ceramic Primer and Linkmax HV and GC Ceramic Primer and Panavia Fluoro Cement showed adhesive failures at the ceramic-resin luting cement interface.

Ictal magnetoencephalographic study in a patient with ring 20 syndrome.

OBJECTIVE: To report the ictal magnetoencephalography (MEG) in a patient with ring chromosome 20 mosaicism, a rare chromosomal anomaly associated with intractable epilepsy. METHODS: MEG and simultaneous EEG were recorded with a 204 channel whole head MEG system. Ten habitual seizures occurred during the acquisition, which was done twice. The equivalent current dipoles (ECDs) for ictal discharges on MEG were calculated using a single dipole model. The ECDs were superimposed on a magnetic resonance image. RESULTS: During the seizures, EEG showed prolonged bursts of 5-6 Hz high voltage slow waves with spike components, dominantly in the bilateral frontal region. MEG showed epileptiform discharges corresponding to the ictal EEG. Ictal discharges on MEG were dominant in the frontal area in the initial portion, and then spread in the bilateral temporal area in the middle of the seizure. ECDs obtained from the spikes of the initial portion were clustered in the medial frontal lobe. CONCLUSIONS: The source of the ictal MEG was localised in the medial frontal lobe. The findings suggest that the mechanism underlying epilepsy in this case might be similar to medial frontal lobe epilepsy. Ictal MEG is a valuable tool for detecting the site of seizure onset.