Metallosupramolecular Multiblock Copolymers of Lanthanide Complexes by Seeded Living Polymerization.

Supramolecular block copolymers, derived via seeded living polymerization, are increasingly recognized for their rich structural and functional diversity, marking them as cutting-edge materials. The use of metal complexes in supramolecular block copolymerization not only offers a broad range of block copolymers through the structural similarity in the coordination geometry of the central metal ion but also controls spectroscopic properties, such as emission wavelength, emission strength, and fluorescence lifetime. However, the exploration of metallosupramolecular multiblock copolymerization based on metal complexes remains quite limited. In this work, we present a pioneering synthesis of metallosupramolecular multiblock copolymers utilizing Eu3+ and Tb3+ complexes as building blocks. This is achieved through the strategic manipulation of nonequilibrium self-assemblies via a living supramolecular polymerization approach. Our comprehensive exploration of both thermodynamically and kinetically regulated metallosupramolecular polymerizations, centered around Eu3+ and Tb3+ complexes with bisterpyridine-modified ligands containing R-alanine units and a long alkyl group, has highlighted intriguing behaviors. The monomeric [R-L1Eu(NO3)3] complex generates a spherical structure as the kinetic product. In contrast, the monomeric [R-L1Eu2(NO3)6] complex generates fiber aggregates as a thermodynamic product through intermolecular interactions such as π-π stacking, hydrophobic interaction, and H-bonds. Utilizing the Eu3+ complex, we successfully conducted seed-induced living polymerization of the monomeric building unit under kinetically regulated conditions. This yielded a metallosupramolecular polymer of precisely controlled length with minimal polydispersity. Moreover, by copolymerizing the kinetically confined Tb3+ complex state ("A" species) with a seed derived from the Eu3+ complex ("B" species), we were able to fabricate metallosupramolecular tri- and pentablock copolymers with A-B-A, and B-A-B-A-B types, respectively, through a seed-end chain-growth mechanism.

Lithium Polystyrene Sulfonate as a Hole Transport Material in Inverted Perovskite Solar Cells.

Despite the exceptional efficiency of perovskite solar cells (PSCs), further improvements can be made to bring their power conversion efficiencies (PCE) closer to the Shockley-Queisser limit, while the development of cost-effective strategies to produce high-performance devices are needed for them to reach their potential as a widespread energy source. In this context, there is a need to improve existing charge transport layers (CTLs) or introduce new CTLs. In this contribution, we introduced a new polyelectrolyte (lithium poly(styrene sulfonate (PSS))) (Li:PSS) polyelectrolyte as an HTL in inverted PSCs, where Li+ can act as a counter ion for the PSS backbone. The negative charge on the PSS backbone can stabilize the presence of p-type carriers and p-doping at the anode. Simple Li:PSS performed poorly due to poor surface coverage and voids existence in perovskite film as well as low conductivity. PEDOT:PSS was added to increase the conductivity to the simple Li:PSS solution before its use which also resulted in lower performance. Furthermore, a bilayer of PEDOT:PSS and Li:PSS was employed, which outperformed simple PEDOT:PSS due to high quality of perovskite film with large grain size also the large electron injection barrier (ϕe ) impeded back diffusion of electrons towards anode. As a consequence, devices employing PEDOT:PSS / Li:PSS bilayers gave the highest PCE of 18.64%.

17% Non-Fullerene Organic Solar Cells with Annealing-Free Aqueous MoO x.

A charge transport layer based on transition metal-oxides prepared by an anhydrous sol-gel method normally requires high-temperature annealing to achieve the desired quality. Although annealing is not a difficult process in the laboratory, it is definitely not a simple process in mass production, such as roll-to-roll, because of the inevitable long cooling step that follows. Therefore, the development of an annealing-free solution-processable metal-oxide is essential for the large-scale commercialization. In this work, a room-temperature processable annealing-free "aqueous" MoO x solution is developed and applied in non-fullerene PBDB-T-2F:Y6 solar cells. By adjusting the concentration of water in the sol-gel route, an annealing-free MoO x with excellent electrical properties is successfully developed. The PBDB-T-2F:Y6 solar cell with the general MoO x prepared by the anhydrous sol-gel method shows a low efficiency of 7.7% without annealing. If this anhydrous MoO x is annealed at 200 °C, the efficiency is recovered to 17.1%, which is a normal value typically observed in conventional structure PBDB-T-2F:Y6 solar cells. However, without any annealing process, the solar cell with aqueous MoO x exhibits comparable performance of 17.0%. In addition, the solar cell with annealing-free aqueous MoO x exhibits better performance and stability without high-temperature annealing compared to the solar cells with PEDOT:PSS.

Tungsten-Doped Zinc Oxide and Indium-Zinc Oxide Films as High-Performance Electron-Transport Layers in N-I-P Perovskite Solar Cells.

Perovskite solar cells (PSCs) have attracted tremendous research attention due to their potential as a next-generation photovoltaic cell. Transition metal oxides in N-I-P structures have been widely used as electron-transporting materials but the need for a high-temperature sintering step is incompatible with flexible substrate materials and perovskite materials which cannot withstand elevated temperatures. In this work, novel metal oxides prepared by sputtering deposition were investigated as electron-transport layers in planar PSCs with the N-I-P structure. The incorporation of tungsten in the oxide layer led to a power conversion efficiency (PCE) increase from 8.23% to 16.05% due to the enhanced electron transfer and reduced back-recombination. Scanning electron microscope (SEM) images reveal that relatively large grain sizes in the perovskite phase with small grain boundaries were formed when the perovskite was deposited on tungsten-doped films. This study demonstrates that novel metal oxides can be used as in perovskite devices as electron transfer layers to improve the efficiency.

Effect of counter-ions on the properties and performance of non-conjugated polyelectrolyte interlayers in solar cell and transistor devices.

We have investigated a series of non-conjugated polyelectrolytes (NPEs) which are based on a polyethylenimine (PEI) backbone with various counterions, such as Br- I- and BIm4 -, as interfacial layers at the electrodes of solar cells and transistor devices to improve the power conversion efficiency (PCE) and device performance. This new series of NPEs with different counterions are capable of forming electric dipoles at NPE/metal electrode interfaces; as a consequence tuning of the energy levels, and work function (WF) of the electrodes is possible. Using this approach, the PCE of organic solar cells could be improved from 1.05% (without NPEs) to 6.77% (with NPEs) while the charge carrier mobility and on/off ratio of FET devices could be improved, showing the broad utility of this type of material. This study provides a novel approach towards investigating the influence of ions on interfacial dipoles and electrode WFs in solution-processed semiconducting devices.