Fabrication of composite transparent conductive electrodes based on silver nanowires.

Composite transparent conductive electrodes (C-TCEs) have recently been produced using low-cost techniques to keep up with the boom in the fabrication and development of optoelectronic devices. In this article, silver nanowires (AgNWs) were successfully synthesized by a simple hydrothermal method using different molecular weights MWs of poly (N-vinylpyrrolidone) (PVP). Graphene oxide (GO) was prepared using the modified Hummers' method and a reduction step was held on GO films to produce reduced GO (rGO). C-TCEs were fabricated by over-coating the AgNWs electrodes with rGO, or poly(3,4-ethylenedioxythiophene) polystyrene sulfonate to improve the roughness, surface energy, and sheet resistance. The influence of using lower and higher MWs of PVP on the yield, shape, and size of AgNWs was investigated. The results showed that using lower MW of PVP had a great effect on the yield, morphology, and aspect ratio of AgNWs with diameter of 46 nm and average length 12 µm. The optical, morphological, topographical, and electrical properties of TCEs were studied. AgNWs/rGO composite electrode provided the lowest surface roughness and surface energy of 250 nm and 47.95 mN/m, respectively, with a relatively high transparency of 78.2% at 550 nm light wavelength, and a low sheet resistance of 27 Ω/□.

Cancer bioimaging using dual mode luminescence of graphene/FA-ZnO nanocomposite based on novel green technique.

Graphene based nanomaterials are explored in the field of cancer bioimaging and biomedical science and engineering. The luminescent nanostructures with a low toxicity and high photostability can be used as probes in bioimaging applications. This work is aimed to prepare graphene/folic acid-zinc oxide (GN/FA-ZnO) nanocomposite with dual-mode emissions (down-conversion and up-conversion) to be used in cancer bioimaging. The dual mode emissions offer long luminescence lifetime, multicolor emissions detected by the naked eyes after excitation and narrow band absorption and emission spectra. ZnO nanospheres and nanorods structures were prepared using co-precipitation technique and were conjugated with FA to separate the bulk graphite layers electrostatically into GN. The optical, morphological, surface charge and structural properties of the prepared nanostructures were investigated and discussed using different characterization techniques such as UV-visible spectroscopy, photoluminescence (PL) spectroscopy, scanning electron microscope (SEM), high resolution transmission electron microscope (HRTEM), Zeta potential, Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), X-ray powder diffraction (XRD), and Fourier transform infrared (FTIR). GN/FA-ZnO nanocomposites were injected into Swiss albino mice implanted with Ehrlich Tumor and the bioimaging was investigated using photon imager and digital camera. The results showed clear fluorescence and confirmed that the green design of GN/FA-ZnO nanocomposite with targeting behavior was capable of selective bioimaging of the tumor. This study presented a novel dual mode emission nanocomposite for tumor targeting and is a promising strategy for the fabrication of a new design of spectral encoding.

Supercapacitor based on polymeric binary composite of polythiophene and single-walled carbon nanotubes.

The aim of this work is to fabricate supercapacitor electrode based on poly (3-hexyl-thiophene-2, 5-diyl) (P3HT) and single-walled carbon nanotubes (SWCNTs) nanocomposites with different ratios onto a graphite sheet as a substrate with a wide voltage window in nonaqueous electrolyte. Structural, morphological and electrochemical properties of the prepared nanocomposites of P3HT/SWCNTs were studied and discussed. The electrochemical properties included cyclic voltammetry (CV), galvanostatic charging-discharging (GCD), and electrochemical impedance spectroscopy (EIS) were investigated. The obtained results indicated that P3HT/SWCNTs nanocomposite possesses higher specific capacitance than that present in its individual component. The high electrochemical performance of the nanocomposite was due to formation of microporous structure which facilitates ions diffusion and electrolyte penetration in these pores. The morphological micrographs of the purified SWCNTs had buckypaper structure while the photomicrographs of P3HT/SWCNTs showed that SWCNTs appear behind and front of the P3HT nanospheres. The specific capacitance of 50% SWCNTs at 0.5 Ag-1 was found to be 245.8 Fg-1 compared with that of pure P3HT of 160.5 Fg-1.

Tuning of strain and surface roughness of porous silicon layers for higher-quality seeds for epitaxial growth.

Sintered porous silicon is a well-known seed for homo-epitaxy that enables fabricating transferrable monocrystalline foils. The crystalline quality of these foils depends on the surface roughness and the strain of this porous seed, which should both be minimized. In order to provide guidelines for an optimum foil growth, we present a systematic investigation of the impact of the thickness of this seed and of its sintering time prior to epitaxial growth on strain and surface roughness. Strain and surface roughness were monitored in monolayers and double layers with different porosities as a function of seed thickness and of sintering time by high-resolution X-ray diffraction and profilometry, respectively. Unexpectedly, we found that strain in double and monolayers evolves in opposite ways with respect to layer thickness. This suggests that an interaction between layers in multiple stacks is to be considered. We also found that if higher seed thickness and longer annealing time are to be preferred to minimize the strain in double layers, the opposite is required to achieve smoother layers. The impact of these two parameters may be explained by considering the morphological evolution of the pores upon sintering and, in particular, the disappearance of interconnections between the porous seed and the bulk as well as the enlargement of pores near the surface. An optimum epitaxial growth hence calls for a trade-off in seed thickness and annealing time, between minimum-strained layers and rougher surfaces. PACS CODES: 81.40.-z Treatment of materials and its effects on microstructure, nanostructure, and properties; 81.05.Rm Porous materials; granular materials; 82.80.Ej X-ray, Mössbauer and other γ-ray spectroscopic analysis methods.