High-Throughput Flow-Through Direct Immunoassays for Targeted Bacteria Detection.

Regulatory authorities require analytical methods for bacteria detection to analyze large sample volumes (typically 100 mL). Currently only the Membrane Filtration and the Most Probable Number assays analyze such large volumes, while other assays for bacteria detection (ELISA, lateral flow assays, etc.) typically analyze volumes 1000 times smaller. This study describes flow-through direct immunoassays (FTDI), a new methodology for the targeted detection of bacteria in liquid samples of theoretically any volume. Flow-through direct immunoassays are performed in fluid-permeable microwells (e.g., wells of a filter well plate) that have a membrane on their bottom where the bacteria are trapped before their detection using a direct immunoassay. Two versions of FTDI assays for the detection of E. coli in 10 mL of sample were developed. A rapid FTDI assay that can be completed in less than 2.5 h can detect E. coli bacteria in levels down to 17 CFU/mL, and an ultrasensitive FTDI assay that employs an additional bacteria culturing step to boost the sensitivity can detect E. coli bacteria in levels lower than 1 CFU/mL in less than 5.5 h. All the steps of the assays, including the immunoassay steps, the culturing step, and the analytical signal measurement step are performed inside the well plate to decrease the chance of contamination and ensure a safe, easy process for the user. The assays were assessed and validated in tap water, river water, and apple juice samples, and the results suggests that the assays are robust, precise, and accurate. When the assays are performed in 96-well filter plates, a filter well plate vacuum manifold and a multichannel peristaltic pump are also used, so multiple samples can be analyzed in parallel to allow high-throughput analysis of samples.

Wearable Thermoelectric Devices Based on Three-Dimensional PEDOT:Tosylate/CuI Paper Composites.

Thermoelectric composites of organic and inorganic materials exhibit significantly enhanced thermoelectric properties compared with pristine organic thermoelectrics so they might be better suited as core materials of wearable thermoelectric devices. This study describes the development of three-dimensional (3D) paper PEDOT:tosylate/CuI composites that could be shaped as 3 mm thick blocks to convert a temperature difference between their bottom and top sides into power; the majority of organic thermoelectric materials are shaped as thin strips usually on a planar substrate and convert a temperature difference between the opposite edges of the strips into power. The 3D paper PEDOT:tosylate/CuI composites can produce a power density equal to 4.8 nW/cm2 (ΔΤ = 6 Κ) that is 10 times higher than that of the pristine paper PEDOT:Tos composites. The enhanced thermoelectric properties of the paper PEDOT:tosylate/CuI composites are attributed to the CuI nanocrystals entrapped inside the composite that increases the Seebeck coefficient of the composite to 225 µV K-1; the Seebeck coefficient of paper PEDOT:Tos is 65 µV K-1. A proof-of-concept wearable thermoelectric device that uses 36 blocks of the paper PEDOT:tosylate/CuI composites (as p-type elements) and 36 wires of monel (as n-type elements) can produce up to 4.7 µW of power at ΔΤ = 20 K. The device has a footprint of 64 cm2 and can be placed directly over the skin or can be embedded into clothing.

Inexpensive, Three-Dimensional, Open-Cell, Fluid-Permeable, Noble-Metal Electrodes for Electroanalysis and Electrocatalysis.

This study describes the fabrication of three-dimensional, open-cell, noble-metal (Au, Ag, and Pt) electrodes that have a complex geometry, i.e., wire mesh, metallic foam, "origami" wire mesh, and helix wire mesh. The electrodes were fabricated using an ultrasonication-assisted electroplating method that deposits a thin, continuous, and defect-free layer of noble metal (i.e., Au, Ag, or Pt) on an inexpensive copper substrate that has the desired geometry. The method is inexpensive, easy to use, and capable of fabricating noble-metal electrodes of complex geometries that cannot be fabricated using established techniques like screen printing or physical vapor deposition. By minimizing the amount of the pure noble metal in the electrodes, their cost drops significantly and could become low enough even for single-use applications; for example, the cost of metal in a Au wire-mesh electrode is $0.007/cm2 of exposed area that is about 400 times lower than that of a wire-mesh electrode composed entirely of Au. The electrodes exhibit an almost identical electrochemical performance to noble-metal electrodes of similar shape composed of bulk noble metal; therefore, these electrodes could replace two-dimensional noble-metal electrodes (e.g., rods, disks, foils) in numerous electroanalytical and electrocatalytical systems or even allow the use of noble-metal electrodes in new applications such as flow-based electrochemical systems. In this study, wire-mesh and metallic foam noble-metal electrodes have been successfully used as working electrodes for the electrocatalytical oxidation of methanol and for the electrochemical detection of redox mediators, lead ions, and nitrobenzene using various electroanalytical techniques.