Effect of Ultraviolet Activation on Sub-ppm NO2 Sensing Dynamics of Poly(3-hexylthiophene)-Bearing Graft Copolymers.

Nitrogen dioxide (NO2) sensors utilising graft copolymers bearing poly(3-hexylthiophene) chains have been developed and investigated in terms of their operation parameters using different carrier gases (N2 or air) and in either dark conditions or with ultraviolet (UV) irradiation. Interestingly, sensor performance improved upon transition from N2 to air, with the inverse being true for most NO2 sensors. UV irradiation both improved sensor dynamics and stabilised the sensor electrical baseline, allowing sensors based on SilPEG to fulfil the requirements of sensing solutions used in industry (below 10% baseline drift after sensors reach saturation) and making them promising candidates for further development and applications. Based on conducted multi-variate experiments, an initial mechanism underlying the interplay of exposure to oxygen (present in air) and UV irradiation was postulated.

Poly(3-hexylthiophene) Grafting and Molecular Dilution: Study of a Class of Conjugated Graft Copolymers.

A type of graft copolymer based on polysiloxane and regioregular poly(3-hexylthiophene) (P3HT) has been synthesised and its properties have been studied alongside those of its parent conjugated polymer-regioregular P3HT. Electrochemical analysis has revealed more significant changes in conformation of the copolymer film than was observed for P3HT. UV-Vis-NIR spectroelectrochemical investigation provided evidence of improved doping reversibility of the copolymer, despite its marginally increased band gap, as also confirmed by electroconductometric analysis. Evidence has been shown, indicating that polaron mobilities in both P3HT and the copolymer are higher than those of bipolaronic charge carriers, even though both systems exhibit standard doping/dedoping patterns. The grafted copolymer was tested in bulk heterojunction solar cells. Preliminary studies show a great potential of these polymers for application in photovoltaics. Power conversion efficiency of up to 2.46% was achieved despite the dilution of the P3HT chains in the copolymer.

A Study on the Impact of Poly(3-hexylthiophene) Chain Length and Other Applied Side-Chains on the NO2 Sensing Properties of Conducting Graft Copolymers.

The detection and concentration measurements of low concentrations of nitrogen dioxide (NO2) are important because of its negative effects on human health and its application in many fields of industry and safety systems. In our approach, conducting graft copolymers based on the poly(3-hexylthiophene) (P3HT) conducting polymer and other side-chains, polyethylene glycol (PEG) and dodec-1-en, grafted on a poly(methylhydrosiloxane) backbone, were investigated. The grafts containing PEG (PEGSil) and dodec-1-en (DodecSil) in two variants, namely, fractions with shorter (hexane fraction -H) and longer (chloroform fraction -CH) side-chains of P3HT, were tested as receptor structures in NO2 gas sensors. Their responses to NO2, within the concentration range of 1-20 ppm, were investigated in an nitrogen atmosphere at different operating temperatures-room temperature (RT) = 25 °C, 50 °C, and 100 °C. The results indicated that both of the copolymers with PEG side-chains had higher responses to NO2 than the materials with dodec-1-en side-chains. Furthermore, the results indicated that, in both cases, H fractions were more sensitive than CH fractions. The highest response to 1 ppm of NO2, from the investigated graft copolymers, had PEGSil H, which indicated a response of 1330% at RT and 1980% at 100 °C. The calculated lower-limit of the detection of this material is lower than 300 ppb of NO2 at 100 °C. This research indicated that graft copolymers of P3HT had great potential for low temperature NO2 sensing, and that the proper choice of other side-chains in graft copolymers can improve their gas sensing properties.

Spectroelectrochemistry of poly(3-hexylthiophenes) in solution.

ABSTRACT: The first comprehensive spectroelectrochemical account of the behaviour of regioregular (RR-P3HT) and statistical (ST-P3HT) poly(3-hexylthiophenes) in solution is presented, in contrast to the many reports dealing with P3HT films merely deposited from solution. The conducted experiments revealed that the two types of P3HTs behave in sharply different ways upon the application of electrochemical stimuli: ST-P3HT readily precipitates at mildly oxidative potentials, while the precipitation of the RR-P3HT takes place to a much lesser extent, even at higher potentials. The two polymers, studied via UV-Vis-NIR-EPR spectroelectrochemistry, exhibited properties mostly in line with earlier reports. Further study revealed that RR-P3HT largely remains in solution, even in its doped form, whereas only traces of the doped ST-P3HT are observed in solution in identical conditions. The high concentration of the doped RR-P3HT in solution can be explained by its ability to form soluble polymer agglomerates, in which the positive charge of the p-doped chains is stabilised by and delocalised over neighbouring, interacting undoped chains. These conclusions are consistent with SEM micrographs, which show that after cycling the potential of the electrode in a solution of ST-P3HT, a uniform layer is formed, covering most of the surface of the electrode, whereas in the case of RR-P3HT surface coverage is marginal and formed layer has the appearance of veined blotches.

Investigation of the Effects of Non-Conjugated Co-Grafts on the Spectroelectrochemical and Photovoltaic Properties of Novel Conjugated Graft Copolymers Based on Poly(3-hexylthiophene).

A new type of polysiloxane copolymers, with conjugated⁻regioregular poly(3-hexylthiophene) (P3HT) and non-conjugated-poly(ethylene glycol) (PEG)-grafts have been synthesised, and their properties have been studied alongside those of the parent conjugated polymer (P3HT). Spectroelectrochemical and conductometric analyses revealed an early rise of the conductance of the polymers. Once spectral changes begin taking place, the conductance is stable, implying a loss of mobility of charge carriers, even though standard doping/dedoping patterns are observed. Prototype bulk heterojunction solar cells have been fabricated, based on P3HT/[6,6]-Phenyl-C61-butyric acid methyl ester (PCBM), as well as by substituting P3HT for each of the copolymers. The prototype solar cells achieved PCEs of up to 2.11%. This is one of the highest reported power conversion efficiency (PCE) for devices based on P3HT with low average molecular weight Mn = 12 kDa. Strong correlation between the structure of the copolymer and its photovoltaic performance was found. Elongation of PEG copolymer chain and the use of methyl group instead of terminal hydroxyl groups significantly improved photovoltaic performance.