Enhancing the Mechanical Properties of Poly(vinyl alcohol) Fibers by Lithium Iodide Addition.

The effect of lithium iodide (LiI) on the mechanical strength, properties, and molecular orientation of poly(vinyl alcohol) (PVA) fibers spun by wet spinning and then heat-stretched was studied. The stretchability of LiI-PVA fibers was improved, and the rupture during stretching was suppressed compared to PVA fibers. In addition, the tensile strength and elastic modulus of the thermally stretched fibers have been significantly improved. It was also found that the addition of LiI improves the molecular orientation of PVA. This was achieved because LiI reduced the hydrogen bonds between the molecular chains of PVA, resulting in reduced crystallinity. Most of the LiI in the fiber could be removed by a coagulation bath and washing during the spinning process. This means that LiI is eventually removed, and the heat-treatment strengthens the hydrogen bonds, resulting in excellent mechanical strength.

Role of Shear Flow on Structure Development during Post-Processing Annealing for Poly(lactic acid).

The effect of shear history on structure development during post-processing annealing was studied using poly(lactic acid) PLA. Since PLA shows a low crystallization rate, quenched films had no crystallinity. Moreover, molecular orientation was not detected in the films. During the annealing procedure beyond its glass transition temperature, however, molecular orientation to the flow direction occurred with the crystallization growth in the films having an appropriate shear history. This peculiar crystal growth during the annealing was most probably attributed to the crystallization from extended chain crystals generated during the applied shear history, although the amount of extended chain crystals was low. The results obtained in this study should be noted because the molecular orientation proceeded due to the annealing history applied. Furthermore, this phenomenon will be used to suppress dimensional change and increase product rigidity.

Improvement in Processability for Injection Molding of Bisphenol-A Polycarbonate by Addition of Low-Density Polyethylene.

The rheological properties and processability at injection molding were studied for bisphenol-A polycarbonate (PC) that was modified by low-density polyethylene (LDPE) having a low shear viscosity. The LDPE addition significantly decreased the steady-state shear viscosity, especially in the high shear rate region. The decrease did not originate from slippage on the die wall but due to interfacial slippage between the PC and dispersed LDPE droplets that deformed to the flow direction to a great extent. As a result of the viscosity decrease, injection pressure largely decreased from 150 to 110 MPa with the addition only 5 wt.% of LDPE. The enhanced flowability also reduced the warpage of the molded product significantly, demonstrating that the processability at injection molding was improved by the addition of LDPE.

Optimum processing conditions for the maximum crystallization rate of poly(3-hydroxybutyrate-co-3-hydroxyhexanoate).

The effect of thermal and shear histories on the crystallization rate of poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) (PHBHHx) was studied. As with other crystalline polymers, the shear history greatly affected the crystallization rate when the shear rate was beyond a critical value, i.e., the inverse of the Rouse relaxation time. Even after the formation of extended chain crystals, spherulite texture was clearly discernable. It grew from certain points on the extended chain crystals. Consequently, a row of spherulites appeared along the flow direction. The resin temperature in the molten state was also significant. When the sample was heated to 170 °C, which is beyond the main melting peak in the differential scanning calorimetry curve, unmolten crystals did not affect the linear viscoelastic properties. They acted as effective nucleating agents for the rest of the polymer during cooling. Therefore, the shear history hardly affected the crystallization rate and the number of spherulites.

Anomalous Strain Recovery after Stress Removal of Graded Rubber.

Mechanical responses after the uniaxial deformation of graded styrene-butadiene rubber (SBR) with a gradient in the crosslink points in the thickness direction were investigated as compared with those of homogenously vulcanized SBR samples. The elongational residual strain of a graded sample was found to depend on the part with a high crosslink density. Therefore, it showed good rubber elasticity. After stress removal, moreover, the graded sample showed a marked warpage. This suggested that shrinking stress acted on the surface with a high crosslink density, which would avoid a crack growth on the surface. The sample shape was then recovered to be flat very slowly, indicating that the shrinking stress worked for a long time. This unique rubber elasticity, i.e., slow strain recovery with an excellent strain recovery, makes graded rubber highly significant.

Novel Transparent Films Composed of Bisphenol-A Polycarbonate and Copolyester.

In this paper, the structure and properties of transparent films composed of bisphenol-A polycarbonate (PC) and a commercially available copolyester, poly(1,4-cyclohexanedimethanol-co-2,2,4,4-tetramethyl-1,3-cyclobutanediol-co-terephthalate) (CPE), were studied. Both PC and CPE films are known to be transparent with good mechanical toughness. It was found that PC/CPE (50/50) showed miscibility in both the molten and solid states, indicating that there is a high possibility for the blend system to be miscible in the whole blend ratios. Because of the miscibility, the blend films showed no light scattering originating from phase separation. The mechanical properties of the films, such as Young's modulus, yield stress, and strain at break, were determined by the blend ratio, and the glass transition temperature increased with the PC content, which corresponded well with the values predicted by the Fox equation. These results demonstrate that the thermal and mechanical properties of the films can only be controlled by the blend ratio. Since these transparent films showed excellent mechanical toughness irrespective of the blend ratios, they can be employed in various applications.

Segregation Behavior of Miscible PC/PMMA Blends during Injection Molding.

Miscible blends composed of bisphenol-A polycarbonate (PC) and poly(methyl methacrylate) (PMMA), in which one of them has low molecular weight, were employed to study the surface segregation behavior during flow. The blend samples showed typical rheological behaviors, such as simple polymer melts without a long-time relaxation mechanism ascribed to phase separation, demonstrating that they were miscible. After injection molding, the amounts of a low molecular weight component on the blend surface were found to be larger than the actual blend ratio. Because the injection-molded products were transparent despite a huge difference in refractive indices between PC and PMMA, they showed no phase separation. This result demonstrated that surface segregation of a low molecular weight component occurred under flow field, which expands the material design such as tough plastics with good scratch resistance and optical fibers with tapered refractive index.

Viscoelastic Properties of Fully Biomass-Based Transparent Plastic Comprising Cellulose Acetate and Citrate Ester.

Viscoelastic properties including melt processability were evaluated for a fully biomass-based glassy plastic comprising cellulose acetate (CA) and triethyl citrate (TEC). The TEC exerted an excellent plasticizing effect without dissolving the CA crystals. Pure CA has poor melt processability. In contrast, the TEC-plasticized CA had good melt-processability at 205 °C, which is lower than the degradation temperature of CA. Extrusion was possible even at 1000 s-1 without any flow instabilities, similar to conventional plastics showing good processability at extrusion. Furthermore, there was marked strain-hardening behavior in the transient elongational viscosity, suggesting that various processing operations are possible, such as a long-chain branched polymer. This biomass-based plastic can be used as a substitute for conventional glassy plastics because it is highly transparent and its softening temperature is above 100 °C.

Complicated Structure Change during Capillary Extrusion of Binary Blends of Polycarbonate and Poly(methyl methacrylate).

The effects of pressure and shear rate on the miscibility of binary blends comprising bisphenol-A polycarbonate (PC) and low molecular weight poly(methyl methacrylate) (PMMA) were investigated using a capillary rheometer. Both pressure and shear rate affected the miscibility. The examination of an extruded strand of the blend provided information about the cause of the phase change. Under high pressure, pressure-induced demixing occurred at temperatures below the lower critical solution temperature (LCST) of the blend. Consequently, the extruded strand became opaque throughout. During shear-induced mixing/demixing, a part of the strand became opaque because of the distribution of the shear rate in the strand. For example, during shear-induced demixing, only the exterior of the strand, i.e., the high shear rate region, became opaque. Above the LCST, shear-induced mixing occurred, and only the center region of the strand became opaque.

Effect of Ultra-High-Molecular-Weight Molecular Chains on the Morphology, Crystallization, and Mechanical Properties of Polypropylene.

The effects of the ultra-high-molecular-weight (UHMW) component of polypropylene (PP) on its rheological properties, crystallization behavior, and solid-state mechanical properties were investigated using various measurement techniques. The terminal relaxation time-determined by measuring the linear viscoelasticity-was increased by adding the UHMW component. The increase in the melt elasticity produced by adding the UHMW component was observed by measuring the steady-state shear flow, although the shear viscosity was not greatly affected. Owing to the long characteristic time of the Rouse relaxation of the UHMW component, PP with the UHMW component formed highly oriented structures through a shear-induced crystallization process. The addition of the UHMW component enhanced the orientation and regularity of crystalline structure for extruded films. Therefore, the Young's modulus, yield stress, and strength were higher in the PP film containing the UHMW component than in one without the UHMW component, irrespective of the direction of tensile deformation.

Impact of Magnesium Salt on the Mechanical and Thermal Properties of Poly(vinyl alcohol).

The effects of magnesium salts with various anion species on the structure and properties of a poly(vinyl alcohol) (PVA) film were studied. The glass transition temperature of the PVA film increased following the addition of a magnesium salt. Furthermore, the salt greatly enhanced the modulus and yield stress and reduced the crystallinity of the film. These effects were attributed to the strong ion-dipole interactions between the magnesium salts and the PVA chains. The strength of interaction, i.e., the reduction of segmental motions, depended on the anion species in the following order: Mg(ClO4)2, MgBr2, MgCl2, Mg(CH3COO)2, and MgSO4. The order corresponded to the Hofmeister series, which predicts the ability to break the structure of water.

Synthesis, Properties, and Biodegradability of Thermoplastic Elastomers Made from 2-Methyl-1,3-propanediol, Glutaric Acid and Lactide.

An innovative type of biodegradable thermoplastic elastomers with improved mechanical properties from very common and potentially renewable sources, poly(L-lactide)-b-poly(2-methyl-1,3-propylene glutarate)-b-poly(L-lactide) (PLA-b-PMPG-b-PLA)s, has been developed for the first time. PLA-b-PMPG-b-PLAs were synthesized by polycondensation of 2-methyl-1,3-propanediol and glutaric acid and successive ring-opening polymerization of L-lactide, where PMPG is an amorphous central block with low glass transition temperature and PLA is hard semicrystalline terminal blocks. The copolymers showed glass transition temperature at lower than -40 °C and melting temperature at 130-152 °C. The tensile tests of these copolymers were also performed to evaluate their mechanical properties. The degradation of the copolymers and PMPG by enzymes proteinase K and lipase PS were investigated. Microbial biodegradation in seawater was also performed at 27 °C. The triblock copolymers and PMPG homopolymer were found to show 9-15% biodegradation within 28 days, representing their relatively high biodegradability in seawater. The macromolecular structure of the triblock copolymers of PLA and PMPG can be controlled to tune their mechanical and biodegradation properties, demonstrating their potential use in various applications.