Electron Beam Irradiated Al Doped ZnO Thin Films as Efficient Tunnel Recombination Junction for Hydrogenated Amorphous Silicon/Cu(In,Ga)Se2 Tandem Solar Cells.

A tunnel recombination junction (TRJ) layer for hydrogenated amorphous silicon (a-Si:H)/ Cu(In,Ga)Se2 (CIGS) tandem solar cells is investigated. An Al-doped zinc oxide (AZO) thin film is applied to the TRJ, and the influence of electron beam (e-beam) irradiation on defects along the TRJ is investigated. The AZO thin films are prepared using radio frequency (RF) sputtering and the e-beam is irradiated at 200 W RF power and 2 keV DC power for 5 min. In the e-beam irradiated AZO thin film, the number of oxygen vacancies and Zn interstitials increases, which in turn strengthens the effect of defect-enhanced tunnel recombination.

Enhanced Photocurrents with ZnS Passivated Cu(In,Ga)(Se,S)2 Photocathodes Synthesized Using a Nonvacuum Process for Solar Water Splitting.

Chalcopyrite Cu(In,Ga)(Se,S)2 (CIGS) semiconductors are potential candidates for use in photoelectrochemical (PEC) hydrogen generation due to their excellent optical absorption properties and high conduction band edge position. In the present research, CIGS thin film was successfully prepared on a transparent substrate (F:SnO2 glass) using a solution-based process and applied for a photocathode in solar water splitting, which shows control of the surface state associated with sulfurization/selenization process significantly influences on the PEC activity. A ZnS passivation surface layer was introduced, which effectively suppresses charge recombination by surface states of CIGS. The CIGS/ZnS/Pt photocathode exhibited highly enhanced PEC activity (∼24 mA·cm-2 at -0.3 V vs RHE). The performances of our CIGS photocathode on the transparent substrate were also characterized under front/back light illumination, and the incident photon to current conversion efficiency (IPCE) drastically changed depending on the illumination directions showing decreased IPCE especially under UV region with back illumination. The slow minority carrier (electron) transportation is suggested as a limiting factor for the PEC activity of the CIGS photocathode.

Effect of Reaction Temperature of CdS Buffer Layers by Chemical Bath Deposition Method.

This study investigated CdS deposition on a Cu(In,Ga)Se2 (CIGS) film via chemical bath deposition (CBD) in order to obtain a high-quality optimized buffer layer. The thickness and reaction temperature (from 50 degrees C to 65 degrees C) were investigated, and we found that an increase in the reaction temperature during CBD, resulted in a thicker CdS layer. We obtained a thin film with a thickness of 50 nm at a reaction temperature of 60 degrees C, which also exhibited the highest photoelectric conversion efficiency for use in solar cells. Room temperature time-resolved photoluminescence (TR-PL) measurements were performed on the Cu(In,Ga)Se2 (CIGS) thin film and CdS/CIGS samples to determine the recombination process of the photo-generated minority carrier. The device performance was found to be dependent on the thickness of the CdS layer. As the thickness of the CdS increases, the fill factor and the series resistance increased to 61.66% and decreased to 8.35 Ω, respectively. The best condition was observed at a reaction temperature of 60 degrees C, and its conversion efficiency was 12.20%.

Characterization of Flexible CIGS Thin Film Solar Cells or Stainless Steel with Intrinsic ZnO Diffusion Barriers.

ZnO diffusion barrier layer was deposited by RF magnetron sputtering by using the same method as intrinsic ZnO layer. The CIGS solar cells were fabricated on stainless steel substrate. The 50-200 nm thin ZnO diffusion barriers effectively reduced the diffusion of Fe and Cr, from stainless steel substrates into the CIGS absorbers. The CIGS solar cells with ZnO diffusion barriers increased the J(sc) and FF, which resulted in an increase of cell efficiency from 5.9% up to 9.06%.

Properties of Electron-Beam Irradiated CuInSe2 Layers by Multi-Step Sputtering Method.

Typically, CuInSe2 (CIS) based thin films for photovoltaic devices are deposited by co-evaporation or by deposition of the metals, followed by treatment in a selenium environment. This article describes CIS films that are instead deposited by DC and RF magnetron sputtering from binary Cu2Se and In2Se3 targets without the supply of selenium. As a novel method, electron beam annealing was used for crystallization of Cu2Se/In2Se3 stacked precursors. The surface, cross-sectional morphology, and compositional ratio of CIS films were investigated to confirm the possibility in crystallization without any addition of selenium. Our work demonstrates that the e-beam annealing method can be a good candidate for the rapid crystallization of Cu-In-Se sputtered precursors.

Investigation on properties of electron-beam treated Mo back contact layer prepared by DC sputtering method.

Molybdenum (Mo) has been used as back contact layer in chalcopyrite solar cells family (CulnSe2 and its alloys) because it showed the excellence of electrical properties such as low resistivity at the Mo interference. Generally, there are strong corrleations between working pressure and properites such as adhesion and conductivity during deposition of Mo layer. Electrical properites might be inversely proportional to adehsion between Mo layer and glass substrate. Several methods have been executed for improvement of electrical properties and ahesion. In this study, DC sputtered Mo back contact layers on sodalime glass were prepared with working pressure range of 1-10 mTorr, and then all samples were treated by rounded exposure of electron beam at DC power of 3 kV for 5 minutes. After electron-beam treatement, all samples showed the lower resisitivity and sheet resisitance than as-deposited Mo layers. As working pressure decreased, grain size of e-beam treated samples gradually increased up to 30.7 nm. E-beam treated Mo layer might be a good candidate as back contact layer of tandem structured CIS families thin film solar cells.

Field modulation in Na-incorporated Cu(In,Ga)Se2 (CIGS) polycrystalline films influenced by alloy-hardening and pair-annihilation probabilities.

The influence of Na on Cu(In,Ga)Se2 (CIGS) solar cells was investigated. A gradient profile of the Na in the CIGS absorber layer can induce an electric field modulation and significantly strengthen the back surface field effect. This field modulation originates from a grain growth model introduced by a combination of alloy-hardening and pair-annihilation probabilities, wherein the Cu supply and Na diffusion together screen the driving force of the grain boundary motion (GBM) by alloy hardening, which indicates a specific GBM pinning by Cu and Na. The pair annihilation between the ubiquitously evolving GBMs has a coincident probability with the alloy-hardening event.PACS: 88. 40. H-, 81. 10. Aj, 81. 40. Cd.