RESUMO
Chemical mechanical polishing/planarization (CMP) is an essential manufacturing process in semiconductor technologies. This method combines chemical and mechanical forces to smooth the surfaces of wafers. The effectiveness of CMP relies on a carefully chosen slurry, demanding a sophisticated manufacturing technology. This technology must seamlessly integrate both chemical composition and mechanical elements, highlighting the intricate synergy required for successful semiconductor fabrication. Particularly in milling processes, if agglomerated particles due to slurry particle corrosion are present during polishing, uneven polishing, numerous fine scratches occur, leading to an increase in roughness and a deterioration in the quality of the finished surface. In this study, to overcome the issue of particle agglomeration and uneven polishing in commonly used ceria nanoparticle slurries during CMP processes, we investigated the ceria nanoparticle behavior based on styrene-maleic acid (SMA) dispersant polymer applied with three types of defoaming polymers. The investigations are expected to open up the possibility of utilizing ceria nanoparticles with applied defoaming polymer as an abrasive for advanced CMP applications. All samples were characterized by DLS (dynamic light scattering), SEM-EDX (scanning electron microscopy-energy dispersive X-ray spectroscopy), pH, conductivity, viscosity, a 10-day stability test at 60 °C, the AF4 test, and the polishing rate efficiency test. Our research demonstrates a significant improvement achieved through the use of SMA dispersant polymer, resulting in a polishing selection ratio exceeding 80 for oxide and nitride films. The G-336 defoaming polymer utilized here is expected to serve as a viable alternative in CMP processes by providing stable uniformity.
RESUMO
Guava (Psidium guajava) is a plant widely distributed in tropical and subtropical regions. Its leaves contain a large amount of physiological molecules such as flavonoid, sesquiterpene, triterpenoid, coumarin, alkaloid, and tannin molecules with antioxidative and anti-inflammatory effects. In this study, the use of concentrated P. guajava leaf extract molecules as a functional natural material was evaluated by confirming the extract's antioxidative, antibacterial, tyrosinase activity inhibition, and collagenase activity inhibition effects and its trans-2-nonenal removal ability. As a result of the analysis of the antioxidant and antibacterial components of concentrated P. guajava leaf extract molecules through GC-MS, a large amount of aromatic hydrocarbon molecules were detected. When different concentrations of ethanol were used for extraction, the leaf extract concentrated with 70% ethanol showed the most effective active molecules. As a result of measuring DPPH radical scavenging activity, a concentration-dependent antioxidant activity was confirmed. The antioxidant activity tended to increase when the ethanol content used for extraction was increased. Molecules such as 2,4-di-tert-butylphenol, caryophyllene oxide, and γ-muurolene in P. guajava leaf extract concentrate appeared to have antibacterial activities against S. aureus bacteria known to cause atopy. As ethanol content increased, the inhibitory effect on tyrosinase activity was increased. In addition, when ethanol content was 50%, the concentrated leaf extract was able to remove trans-2-nonenal by 52.4%. As a result of determining the concentrated leaf extract's collagenase inhibition activity, an inhibition rate close to that of ascorbic acid, a positive control, was confirmed. The concentrated guajava leaf extract molecules were confirmed to have whitening and wrinkle-improving functionality. Thus, the P. guajava leaf extract has high potential as a food and natural cosmetic material.
RESUMO
Carbon black (CB) particles tend to aggregate in aqueous solutions, and finding an optimum dispersing condition (e.g., selection of the type of dispersant) is one of the important tasks in related industries. In the present study, three types of styrene maleic acid (SMA) copolymer dispersants were synthesized, labeled respectively 'SMA-1000', 'SMA-2000', and 'SMA-3000', which have 1, 2, and 3 styrene groups in their repeating units. Then, asymmetrical flow field-flow fractionation (AsFlFFF) was employed to measure the particle size distributions of the aqueous CB dispersions. For the particle size analysis of the CB dispersions, dynamic light scattering (DLS) showed relatively lower reproducibility than AsFlFFF. AsFlFFF showed that the use of SMA-3000 yielded a CB dispersion with the most uniform particle size distribution. When the SMA-3000 dispersant was used, the particle size tended to increase after 1 h of milling as the milling time increased, probably due to the re-agglomeration of the particles by excessive milling. The particle size distributions from AsFlFFF were consistent with the colorimetric observations. With the SMA-3000 dispersant, the lowest L∗ value was observed after 1 h of milling. The AsFlFFF and colorimetric analyses suggest that a stable CB dispersion can be obtained by either 3-h of milling with the SMA-2000 or 1-h of milling with the SMA-3000.
RESUMO
In this work, a polymeric nickel complex-modified indium tin oxide (ITO) electrode was prepared by a one-step cold-plasma process of acrylic-Ni complex precursors. Also, the work provides the electrocatalytic oxidation of methanol by a polymeric Ni complex-modified electrode prepared by a simple one-step cold-plasma process. The acrylic-Ni complex precursors were synthesized by complexation of nickel (II) chloride, and acrylic acid in a small amount of water; subsequently we added N,N'-methylene-bis-acrylamide as a crosslinking agent to the complex solution. We characterized the prepared polymeric Ni complex-modified (Ni-modified) catalytic electrode by X-ray photoelectron spectroscopy, field emission scanning electron microscopy, and electrochemical methods. Electrochemical characterization showed stable redox behavior of Ni(III)/Ni(II) couples. Cyclic voltammetric experiments have shown that electrocatalytic oxidation of methanol can occur on Ni-modified catalytic electrodes, while not observed on bare ITO. As a result, this work provides the simple and easy preparation of electrocatalysts by one-step plasma process for methanol fuel cell.
RESUMO
Polymer brush is a soft material unit tethered covalently on the surface of scaffolds. It can induce functional and structural modification of a substrate's properties. Such surface coating approach has attracted special attentions in the fields of stem cell biology, tissue engineering, and regenerative medicine due to facile fabrication, usability of various polymers, extracellular matrix (ECM)-like structural features, and in vivo stability. Here, we summarized polymer brush-based grafting approaches comparing self-assembled monolayer (SAM)-based coating method, in addition to physico-chemical characterization techniques for surfaces such as wettability, stiffness/ elasticity, roughness, and chemical composition that can affect cell adhesion, differentiation, and proliferation. We also reviewed recent advancements in cell biological applications of polymer brushes by focusing on stem cell differentiation and 3D supports/implants for tissue formation. Understanding cell behaviors on polymer brushes in the scale of nanometer length can contribute to systematic understandings of cellular responses at the interface of polymers and scaffolds and their simultaneous effects on cell behaviors for promising platform designs. [BMB Reports 2016; 49(12): 655-661].
