Single-Crystalline Nanobelts Composed of Transition Metal Ditellurides.

Following the celebrated discovery of graphene, considerable attention has been directed toward the rich spectrum of properties offered by van der Waals crystals. However, studies have been largely limited to their 2D properties due to lack of 1D structures. Here, the growth of high-yield, single-crystalline 1D nanobelts composed of transition metal ditellurides at low temperatures (T ≤ 500 °C) and in short reaction times (t ≤ 10 min) via the use of tellurium-rich eutectic metal alloys is reported. The synthesized semimetallic 1D products are highly pure, stoichiometric, structurally uniform, and free of defects, resulting in high electrical performances. Furthermore, complete compositional tuning of the ternary ditelluride nanobelts is achieved with suppressed phase separation, applicable to the creation of unprecedented low-dimensional materials/devices. This approach may inspire new growth/fabrication strategies of 1D layered nanostructures, which may offer unique properties that are not available in other materials.

Phase conversion of tricalcium phosphate into Ca-deficient apatite during sintering of hydroxyapatite-tricalcium phosphate biphasic ceramics.

In this study, we report a new observation on the phase conversion that occurs during the sintering of hydroxyapatite (HA)-tricalcium phosphate (TCP) biphasic ceramics. During the sintering of the HA-TCP mixture powders, a large amount of TCP was converted into HA, as detected by X-ray diffraction. The amount of TCP transformed into HA was approximately 10-90% of that initially added. From the electron probe microscopy analysis, the HA transformed from TCP was found to be Ca-deficient with Ca/P ratios of 1.62-1.64. The dissolution behavior and osteoblastic responses in a series of HA-TCP biphasic ceramics (10-90% TCP) were assessed. The solubility of the HA-TCP biphasic ceramics was intermediate between that of the HA and TCP pure ceramics. However, in the case of the HA-90% TCP biphasic ceramic, the solubility was even higher than that of pure TCP. The cell proliferation and alkaline phosphatase activity of the cells on the biphasic ceramics were lower than those on pure HA, but higher than those on pure TCP. However, particularly in the HA-50% TCP biphasic composition, the cellular responses were significantly higher than those on pure HA. It is considered that the Ca-deficient apatite newly formed from the TCP may affect in some way the solubility and biological properties of the HA-TCP biphasic ceramics.

Fluoride coatings on orthodontic wire for controlled release of fluorine ion.

The purpose of this study was to develop a new method of releasing fluorine in a controlled manner for applications in the field of orthodontic Ti-based wire, namely the coating of fluorides on Ti. Thin films of two fluoride compounds, CaF(2) and MgF(2), were coated on Ti via the electron-beam evaporation method. The fluorine was released rapidly from the as-deposited MgF(2) coating within a short period(,) and then the release rate slowed down. When the MgF(2) coating was heat treated, this initial burst effect was decreased, but a significant amount of cracks were generated. On the other hand, in the case of the as-deposited CaF(2) coating, fluorine was released linearly for the entire period, without an initial burst. In the heat-treated CaF(2) coatings the trend was similarly observed. The linear fluorine release from the CaF(2) coatings, even in the as-deposited state, was attributed to the high degree of crystallinity of the coatings. A preliminary cell test showed favorable cell viability on both the fluoride coatings. Given their sustained and controlled fluorine release, these fluoride coatings, particularly CaF(2), are suggested to be potentially useful in the field of orthodontic Ti-based wire.

Biocompatibility of titanium implants modified by microarc oxidation and hydroxyapatite coating.

A thin hydroxyapatite (HA) layer was coated on a microarc oxidized titanium (MAO-Ti) substrate by means of the sol-gel method. The microarc oxidation (anodizing) enhanced the biocompatibility of the Ti, and the bioactivity was improved further by the sol-gel HA coating on the anodized Ti. The HA sol was aged fully to obtain a stable and phase-pure HA, and the sol concentration was varied to alter the coating thickness. Through the sol-gel HA coating, the Ca and P concentrations in the coating layer increased significantly. However, the porous morphology and roughness of the MAO-Ti was altered very little by the sol-gel treatment. The proliferation and alkaline phosphatase (ALP) activity of the osteoblast-like cells on the MAO/HA sol-gel-treated Ti were significantly higher than those on the MAO-Ti without the HA sol-gel treatment.

Fluoridated apatite coatings on titanium obtained by electron-beam deposition.

In this report, a series of fluoridated apatite coatings were obtained by the electron-beam deposition method. The fluoridation of the apatite was aimed to improve the stability of the coating and elicit the fluorine effect, which is useful in the dental restoration area. Apatites fluoridated at different levels were used as initial evaporants for the coatings. The as-deposited coatings were amorphous, but after heat treatment at 500 degrees C for 1 h, the coatings crystallized well to an apatite phase without forming any cracks. The adhesion strengths of the as-deposited coatings were about 40 MPa. After heat treatment at 500 degrees C, the strengths of the pure HA and FA coatings decreased to about 20 MPa, however, the partially fluoridated coatings maintained their initial strength. The dissolution rate of the fluoridated coatings was lower than that of the pure HA coating, and the rate was the lowest in the coatings with 25% and 50% fluorine substitutions. The osteoblast-like cells responded to the coatings in a similar manner to the dissolution behavior. The cells on the fluoridated coatings showed a lower (p < 0.05) proliferation level compared to those on the pure HA coating. The alkaline phosphatase activity of the cells was slightly lower than that on the pure HA coating, but this difference was not statistically significant.

Improvement in biocompatibility of ZrO2-Al2O3 nano-composite by addition of HA.

The biocompatibility of zirconia-alumina (ZA) nano-composites in load-bearing applications such as dental/orthopedic implants was significantly enhanced by the addition of bioactive HA. The ZA matrix was composed of nano-composite powder obtained from the Pechini process and had higher flexural strength than conventionally mixed zirconia-alumina composite. Because the ZA nano-composite powder effectively decreased the contact area between HA and zirconia for their reaction during the sintering process, the HA-added ZA nano-composites contained biphasic calcium phosphates (BCP) of HA/TCP and had higher flexural strength than conventionally mixed ZA-HA composite. From the in vitro test with osteoblastic cell-lines, the proliferation and the differentiation (as expressed by the alkaline phosphatase activity) of the cellular response on the HA-added ZA nano-composites gradually increased as the amount of HA added increased. From the mechanical and biological evaluations of the HA-added ZA nano-composites, 30HA (30 vol% HA + 70 vol% ZA) was found to be the optimal composition for load-bearing biological applications.

Stability and cellular responses to fluorapatite-collagen composites.

Fluorapatite (FA)-collagen composites were synthesized via a biomimetic coprecipitation method in order to improve the structural stability and cellular responses. Different amounts of ammonium fluoride (NH4F), acting as a fluorine source for FA, were added to the precipitation of the composites. The precipitated composites were freeze-dried and isostatically pressed in a dense body. The added fluorine was incorporated nearly fully into the apatite structure (fluoridation), and a near stoichiometric FA-collagen composite was obtained with complete fluoridation. The freeze-dried composites had a typical biomimetic network, consisting of collagen fibers and precipitates of nano-sized apatite crystals. The human osteoblast-like cells on the FA-collagen composites exhibited significantly higher proliferation and differentiation (according to alkaline phosphatase activity) than those on the hydroxyapatite-collagen composite. These enhanced osteoblastic cell responses were attributed to the fluorine release and the reduced dissolution rate.

Strontium substituted calcium phosphate biphasic ceramics obtained by a powder precipitation method.

Strontium (Sr) substituted calcium phosphate ceramics were fabricated using a powder precipitation method. The Sr ions were added up to 8 mol % to replace the Ca ions during the powder preparation. Composition analysis showed that the added Sr was not fully incorporated within the as-precipitated apatite structure, presumably being washed out during the powder preparation. After calcination, the Sr containing powders were crystallized into apatite and tricalcium phosphate (TCP), that is, biphasic calcium phosphates were formed. The amount of TCP increased with increasing the Sr addition. The lattice parameters of the calcined powders increased gradually with Sr substitution in both the a- and c-axis. However, the obtained values deviated slightly from the calculated ones at higher Sr additions (>4%) due to the partial substitution of Sr ions. The microstructure of the sintered bodies changed with the Sr addition due to the formation of TCP. The Vickers hardness increased slightly from 5.2 to 5.5 MPa with increasing Sr addition, which was driven by the HA+TCP biphasic formation. The osteoblast-like cells cultured on the Sr-substituted biphasic sample spread and grew actively. The proliferation rate of the cells was higher in the samples containing more Sr. The alkaline phosphate activity of the cells was expressed to a higher degree with increasing Sr addition. These observations confirmed the enhanced cell viability and differentiation of the Sr-substituted biphasic calcium phosphate ceramics.

Sol-gel derived fluor-hydroxyapatite biocoatings on zirconia substrate.

Fluor-hydroxyapatite (FHA) film was coated on a zirconia (ZrO(2)) substrate by a sol-gel method. An appropriate amount of F ions was incorporated into the hydroxyapatite (HA) during the preparation of the sols. The apatite phase began to crystallize after heat treatment at 400 degrees C, and increased in intensity above 500 degrees C. No decomposition was detected by X-ray diffraction analyses up to 800 degrees C, which illustrates the high thermal stability of the FHA films. The films showed a uniform and dense morphology with a thickness of approximately 1 microm after a precisely controlled heat treatment process. These FHA films adhered firmly to the zirconia substrate, representing notable adhesion strengths of approximately 70 MPa after heat treatment above 500 degrees C. The dissolution rate of the FHA coating layer varied according to the heat treatment temperature, which was closely related to the film crystallinity. The dissolution rate of the FHA film was lower than that of the HA film, suggesting the possibility of a functional gradient coating of HA and FHA. The MG63 cells seeded onto the FHA films proliferated in a similar manner to those seeded onto pure HA ceramic and a plastic control.

Improved biological performance of Ti implants due to surface modification by micro-arc oxidation.

The surface of a titanium (Ti) implant was modified by micro-arc oxidation (MAO) treatment. A porous layer was formed on the Ti surface after the oxidation treatment. The phase and morphology of the oxide layer were dependent on the voltage applied during the oxidation treatment. With increasing voltage, the roughness and thickness of the film increased and the TiO(2) phase changed from anatase to rutile. During the MAO treatment, Ca and P ions were incorporated into the oxide layer. The in vitro cell responses of the specimen were also dependant on the oxidation conditions. With increasing voltage, the ALP activity increased, while the cell proliferation rate decreased. Preliminary in vivo tests of the MAO-treated specimens on rabbits showed a considerable improvement in their osseointegration capability as compared to the pure titanium implant.

Hydroxyapatite-based composite for dental implants: an in vivo removal torque experiment.

Screw-shaped dental implants were fabricated from commercially pure Ti (c.p. Ti) and HA-based composites. The HA-based composites were fabricated by mixing HA with Al(2)O(3)-coated ZrO(2) powders. The mechanical properties of these composites were enhanced by a factor of 3. These were implanted into the rabbit tibiae and the removal torque to loosen the implants in vivo was measured in order to investigate the osteointegration. After a healing period of 6 weeks, the implants were retrieved with a torque gauge instrument. The HA-based composite implants showed an almost 2-times-higher removal torque when compared to the Ti implants (ANOVA, p < 0.05), indicating excellent biocompatibility to bone. Thus, HA-based composites had not only better mechanical properties but also similar bioactivity as HA itself. It is believed that a HA-based composite is suitable for artificial dental implants.

Effect of calcinations of starting powder on mechanical properties of hydroxyapatite-alumina bioceramic composite.

The effect of calcinations of starting powder on the mechanical properties of hydroxyapatite (HA)-based bioceramic composite was investigated. The calcinations of HA powder in air at 900 degrees C increased the crystallinity as well as the size of the powder. Ball milling after the calcinations was effective in eliminating large agglomerates in the powder. When the powder was mixed with reinforcing Al(2)O(3) powder, the mixture became fine and homogeneous. The flexural strength of HA-Al(2)O(3) composite was increased by the calcinations processes at all the Al(2)O(3) concentration. However, the fracture toughness was not much influenced by the calcinations. These results lead to the conclusion that the calcinations process effectively reduced the critical flaw size in the body by removing the agglomerates in the HA powder.