Reducing oil droplet sizes from a subsea oil and gas release by water jetting a laboratory study performed at different scales.

The main objective of subsea mechanical dispersion (SSMD) is to reduce the oil droplet sizes from a subsea oil release, thereby influencing the fate and behaviour of the released oil in the marine environment. Subsea water jetting was identified as a promising method for SSMD and imply that a water jet is used to reduce the particle size of the oil droplets initially formed from the subsea release. This paper presents the main findings from a study including small-scale testing in a pressurised tank, via laboratory basin testing, to large-scale outdoor basin testing. The effectiveness of SSMD increases with the scale of the experiments. From a five-fold reduction in droplet sizes for small-scale experiments to more than ten-fold for large-scale experiments. The technology is ready for full-scale prototyping and field testing. Large-scale experiments performed at Ohmsett indicate that SSMD could be comparable to subsea dispersant injection (SSDI) in reducing oil droplet sizes.

UV degradation of natural and synthetic microfibers causes fragmentation and release of polymer degradation products and chemical additives.

A high proportion of the total microplastic (MP) load in the marine environment has been identified as microfibers (MFs), with polyester (PET) and polyamide (PA) typically found in the highest abundance. The potential for negative environmental impacts from MPs may be dependent on their degree of degradation in the environment, which is influenced by both intrinsic properties (polymer type, density, size, additive chemicals) and extrinsic environmental parameters. Most polymer products break down slowly through a combination of environmental processes, but UV degradation can be a significant source of degradation. The current study aimed to investigate the effect of UV irradiance on the degradation of natural (wool) and synthetic (PET and PA) MFs. Degradation of MFs was conducted in seawater under environmentally relevant accelerated exposure conditions using simulated sunlight. After 56 days of UV exposure, PA primarily exhibited changes in surface morphology with no significant fragmentation observed. PET and wool fibers exhibited both changes in surface morphology and fragmentation into smaller particles. A range of molecular degradation products were identified in seawater leachates after UV exposure, with increasing abundance over the duration of the experiment. Furthermore, a variety of additive chemicals were shown to leach from the MFs into seawater. While some of these chemicals were also susceptible to UV degradation and some are expected to biodegrade rapidly, others may be persistent and contribute to the overall load of chemical pollution in the marine environment.

Interfacial tension between oil and seawater as a function of dispersant dosage.

This paper presents a compilation of data describing interfacial tension between oil and seawater (IFT(oil-water)) as a function of dispersant dosage. The data are from several earlier laboratory studies simulating subsea oil blowouts to evaluate subsea injection of dispersant (SSDI). Three dispersants were tested with four oil types to give a large variation in oil properties (paraffinic, light, waxy and asphaltenic). A general expression for IFT(oil-water) as a function of dispersant dosage is proposed based on the compiled data. IFT(oil-water) versus dosage is needed by algorithms to predict oil droplet sizes from subsea releases. However, such a relationship based on averaged data should be used with care and IFT measurements on the actual oil-dispersant combination should always be preferred.

Subsea dispersants injection (SSDI), effectiveness of different dispersant injection techniques - An experimental approach.

The main objective with this study has been to study injection techniques for subsea dispersant injection (SSDI) to recommend techniques relevant for both laboratory studies and operational response equipment. The most significant factor was the injection point of the dispersant in relation to the release of the oil. The dispersant should be injected immediately before or after the oil is released. Then the dispersant will mix into the oil and reduce IFT before the oil enters the turbulent zone where initial droplet formation occurs. All injection techniques tested gave significant reductions in oil droplet sizes. However, due to the rapid oil droplet formation in turbulent jets and possible formation of surfactant aggregates in the oil, premixing of dispersants should not be used for experimental studies of subsea dispersant injection. This could underestimate dispersant effectiveness and produce results that might not be representative for up-scaled field conditions.