Graphite-type activated carbon from coconut shell: a natural source for eco-friendly non-volatile storage devices.

Carbon from biomass as an active material for supercapacitor electrodes has attracted much interest due to its environmental soundness, abundance, and porous nature. In this context, activated carbon prepared from coconut shells via a simple activation process (water or steam as activation agents) was used as an active material in electrodes for eco-friendly supercapacitors. X-ray diffraction (XRD), Raman spectroscopy, conductivity, scanning electron microscopy (SEM), N2 sorption and thermogravimetry coupled to mass spectrometry (TGA-MS) studies revealed that activated carbon produced by this approach exhibit a graphitic phase, a high surface area, and large pore volume. The energy storage properties of activated carbon electrodes correlate with the morphological and structural properties of the precursor material. In particular, electrodes made of activated carbon exhibiting the largest Brunauer-Emmett-Teller (BET) surface area, i.e. 1998 m2 g-1, showed specific capacitance of 132.3 F g-1 in aqueous electrolyte (1.5 M H2SO4), using expanded graphite sheets as current collector substrates. Remarkably, this sample in a configuration with ionic liquid (1-methyl-1-propy-pyrrolizinium bis(fluorosulfonyl)mide) (MPPyFSI) as electrolyte and a polyethylene separator displayed an outstanding storage capability and energy-power handling capability of 219.4 F g-1 with a specific energy of 92.1 W h kg-1 and power density of 2046.9 W kg-1 at 1 A g-1 and maintains ultra-high values at 30 A g-1 indicating the ability for a broad potential of energy and power related applications. To the best of our knowledge, these values are the highest ever reported for ionic liquid-based supercapacitors with activated carbon obtained from the biomass of coconut shells.

Powder Pressed Cuprous Iodide (CuI) as A Hole Transporting Material for Perovskite Solar Cells.

This study focuses on employing cuprous iodide (CuI) as a hole-transporting material (HTM) in fabricating highly efficient perovskite solar cells (PSCs). The PSCs were made in air with either CuI or 2,2',7,7'-Tetrakis[N,N-di(4-methoxyphenyl)amino]-9,9'-spirobifluorene (spiro-OMeTAD) as HTMs. A simple and novel pressing method was employed for incorporating CuI powder layer between perovskite layer and Pt top-contact to fabricate devices with CuI, while spiro-OMeTAD was spin-coated between perovskite layer and thermally evaporated Au top-contact to fabricate devices with spiro-OMeTAD. Under illuminations of 100 mW/cm2 with an air mass (AM) 1.5 filter in air, the average short-circuit current density (JSC) of the CuI devices was over 24 mA/cm2, which is marginally higher than that of spiro-OMeTAD devices. Higher JSC of the CuI devices can be attributed to high hole-mobility of CuI that minimizes the electron-hole recombination. However, the average power conversion efficiency (PCE) of the CuI devices were lower than that of spiro-OMeTAD devices due to slightly lower open-circuit voltage (VOC) and fill factor (FF). This is probably due to surface roughness of CuI powder. However, optimized devices with solvent-free powder pressed CuI as HTM show a promising efficiency of over 8.0 % under illuminations of 1 sun (100 mW/cm2) with an air mass 1.5 filter in air, which is the highest among the reported efficiency values for PSCs fabricated in an open environment with CuI as HTM.

Structural Evolution of Hydrothermally Derived Reduced Graphene Oxide.

Hydrothermal reduction is a promising approach for graphene oxide (GO) reduction since it is environmentally friendly, simple, and cost effective. We present a detailed study of structural changes occurring in graphene oxide during the reduction process. The correlations between the interlayer spacing, chemical states, work functions, surface morphology, level of disorders, the number of layers, and processing time are elucidated. The results reveal that GO flakes remain in the early stage of the reduction process and that they are fully reduced after a 4-h hydrothermal treatment. With an increase in the reduction time, the resulting product, i.e., reduced graphene oxide, has a low oxygen content, small interlayer spacing, and crumbled and wrinkled structures. We are convinced that these properties can be tuned to a desired level for various applications.

Tuning chemistry of CuSCN to enhance the performance of TiO2/N719/CuSCN all-solid-state dye-sensitized solar cell.

CuSCN with enhanced p-type conductivity was prepared by replacing some of the cuprous sites by triethylamine coordinated Cu(I) with concomitant (SCN)(2) doping to introduce more holes. A compound Cu(5)[(C(2)H(5))(3)N](3)(SCN)(11) was isolated and well characterized. A 41% enhancement of energy conversion efficiency of the TiO(2)/N719/modified CuSCN cell from the best reported value and more than a factor of ten from bare CuSCN was achieved.

A lymphoepithelial cyst (branchial cyst) in the floor of the mouth.

Lymphoepithelial cysts are developmental, but their pathogenesis is unknown. The classical explanation is that they are derived from remnants of the branchial arches or clefts. This has been disputed, and it is likely that most arise from epithelium, possibly of tonsillar or salivary origin, that becomes entrapped by lymphoid tissue. This report describes a lymphoepithelial cyst in a 29-year-old man. The cyst was situated on the right side of the floor of the mouth adjacent to the lingual frenum. Its appearance supports both branchiogenic and the entrapment theories.