New Method for Photoactive Cement Preparation-Selected Mechanical Properties and Photocatalytic Activity of New Materials.

In this study, a new method of obtaining photoactive cements is presented. The goal was to obtain photoactive cements using a method that could reduce the production costs. In the study, an intermediate product from the production of titanium dioxide using the sulfate method, taken from the installation before the calcination process, was used to obtain photoactive cements. Laboratory conditions corresponding to introducing this amorphous TiO2 into cement clinker during its cooling were simulated. The study shows that the temperature from 300 to 800 °C and the time of amorphous TiO2 contact with the cement clinker within 30 min is sufficient to obtain a photoactive cement. The highest photocatalytic activity was obtained for the material with 5 wt.% TiO2 content, and the method used did not cause a significant decrease in the bending and compressive strength of the new photoactive cements. The obtained materials were characterized by determining the crystal size of the TiO2, the sulfur content and the photocatalytic activity during NO decomposition under UV radiation. The bending and compressive strength were measured. The influence of the addition of photocatalysts on the beginning and end of the setting time was also investigated.

On the Selectivity of Simultaneous CO2 and N2 Reduction Using TiO2/Carbon Sphere Photocatalysts Prepared by Microwave Treatment and Mounted on Silica Cloth.

This paper presents new photocatalysts obtained by treating carbon spheres (CS) and TiO2 in a microwave reactor at a pressure of 20 atm and a temperature of up to 300 °C for 15 min and then depositing TiO2/CS composites on glass fibre cloths. Such highly CO2-adsorbing photocatalysts showed photoactivity in the simultaneous water-splitting process, generating H2, reducing CO2 to CO and CH4, and reducing N2 to NH3. In addition, calculations of the hydrogen balance involved in all reactions were performed. Adding 1 g of carbon spheres per 1 g of TiO2 maintained the high selectivity of nitrogen fixation at 95.87-99.5%, which was continuously removed from the gas phase into the water as NH4+ ions.

Photocatalytic Inactivation of Co-Culture of E. coli and S. epidermidis Using APTES-Modified TiO2.

The presented work shows the antibacterial activity of TiO2 photocatalysts modified by 3-aminopropyltriethoxysilane (APTES). The APTES-functionalized TiO2 samples were obtained by the solvothermal process followed by calcination. The antibacterial activity of APTES/TiO2 samples was evaluated with two species of bacteria, Escherichia coli and Staphylococcus epidermidis, under artificial solar light (ASL) irradiation. The used bacteria are model organisms characterized by negative zeta potential (approx. -44.2 mV for E. coli and -42.3 mV for S. epidermidis). For the first time, the antibacterial properties of APTES-functionalized TiO2 were evaluated against mono- and co-cultured bacteria. The high antibacterial properties characterized the obtained APTES-modified nanomaterials. The best antibacterial properties were presented in the TiO2-4 h-120 °C-300 mM-Ar-300 °C sample (modified with 300 mM of APTES and calcined at 300 °C). The improvement of the antibacterial properties was attributed to a positive value of zeta potential, high surface area, and porous volume.

CO2 Sorbents Based on Spherical Carbon and Photoactive Metal Oxides: Insight into Adsorption Capacity, Selectivity and Regenerability.

This work aimed to obtain hybrid composites based on photoactive metal oxide and carbon having adsorption properties. The materials, composed of titanium dioxide or zinc oxide and spherical carbon, were obtained from resorcinol-formaldehyde resin, treated in a solvothermal reactor heated with microwaves and then subjected to carbonization, were received. The functional groups of pure carbon spheres (unsaturated stretching C=C, stretching C-OH and C-H bending vibrations), CS/ZnO and CS/TiO2 samples were determined by FT-IR analysis. The characteristic bands for ZnO and TiO2 were observed below 1000 cm-1. The thermal oxidative properties are similar for TiO2- and ZnO-modified carbon spheres. We have observed that the increased carbon sphere content in nanocomposites results in starting the decomposition process at a lower temperature, therefore, nanocomposites have a broader combustion temperature range. The effect of the oxides' addition to carbon spheres on their adsorption properties was evaluated in detail by examining CO2 adsorption from the gas phase. The selectivity of CO2 over N2 at a temperature of 25 °C and pressure of 1 bar (a novelty in testing CS-based sorbents) calculated for 3.00 CS/TiO2 and 4.00 CS/ZnO was 15.09 and 16.95, respectively. These nanocomposites exhibit excellent cyclic stability checked over 10 consecutive adsorption-desorption cycles.

The Benefits of Using Saccharose for Photocatalytic Water Disinfection.

In this work, the characteristics of saccharose (sucrose)-modified TiO2 (C/TiO2) photocatalysts obtained using a hydrothermal method at low temperature (100 °C) are presented. The influence of C/TiO2 on survivability and enzyme activity (catalase and superoxide dismutase) of Gram-negative bacteria Escherichia coli (ATCC 29425) and Gram-positive bacteria Staphylococcus epidermidis (ATCC 49461) under UV-A and artificial solar light (ASL) were examined. The obtained TiO2-1%-S-100 photocatalysts were capable of total E. coli and S. epidermidis inactivation under ASL irradiation in less than 1 h. In addition, the impacts of sugars on the photocatalytic activity and disinfection performance are discussed.

New Insight on Carbon Dioxide-Mediated Hydrogen Production.

A new approach to hydrogen production from water is described. This simple method is based on carbon dioxide-mediated water decomposition under UV radiation. The water contained dissolved sodium hydroxide, and the solution was saturated with gaseous carbon dioxide. During saturation, the pH decreased from about 11.5 to 7-8. The formed bicarbonate and carbonate ions acted as scavengers for hydroxyl radicals, preventing the recombination of hydroxyl and hydrogen radicals and prioritizing hydrogen gas formation. In the presented method, not yet reported in the literature, hydrogen production is combined with carbon dioxide. For the best system with alkaline water (0.2 m NaOH) saturated with CO2 under UV-C, the hydrogen production amounted to 0.6 µmol h-1 during 24 h of radiation.

Magnetic Resonance Studies of Hybrid Nanocomposites Containing Nanocrystalline TiO2 and Graphene-Related Materials.

Nanocomposites based on nanocrystalline titania modified with graphene-related materials (reduced and oxidized form of graphene) showed the existence of magnetic agglomerates. All parameters of magnetic resonance spectra strongly depended on the materials' modification processes. The reduction of graphene oxide significantly increased the number of magnetic moments, which caused crucial changes in the reorientation and relaxation processes. At room temperature, a wide resonance line dominated for all nanocomposites studied and in some cases, a narrow resonance line derived from the conduction electrons. Some nanocomposites (samples of titania modified with graphene oxide, prepared with the addition of water or butan-1-ol) showed a single domain magnetic (ferromagnetic) arrangement, and others (samples of titania modified with reduced graphene oxide) exhibited magnetic anisotropy. In addition, the spectra of EPR from free radicals were observed for all samples at the temperature of 4 K. The magnetic resonance imaging methods enable the capturing of even a small number of localized magnetic moments, which significantly affects the physicochemical properties of the materials.

The Effect of the Modification of Carbon Spheres with ZnCl2 on the Adsorption Properties towards CO2.

Zinc chloride and potassium oxalate are often applied as activating agents for carbon materials. In this work, we present the preparation of ZnO/carbon spheres composites using resorcinol-formaldehyde resin as a carbon source in a solvothermal reactor heated with microwaves. Zinc chloride as a zinc oxide source and potassium oxalate as an activating agent were applied. The effect of their addition and preparation conditions on the adsorption properties towards carbon dioxide at 0 °C and 25 °C were investigated. Additionally, for all tested sorbents, the CO2 sorption tests at 40 °C, carried out utilizing a thermobalance, confirmed the trend of sorption capacity measured at 0 and 25 °C. Furthermore, the sample activated using potassium oxalate and modified using zinc chloride (a carbon-to-zinc ratio equal to 10:1) displayed not only a high CO2 adsorption capacity (2.69 mmol CO2/g at 40 °C) but also exhibited a stable performance during the consecutive multicycle adsorption-desorption process.

Artificial Solar Light-Driven APTES/TiO2 Photocatalysts for Methylene Blue Removal from Water.

A visible-light photocatalytic performance of 3-aminopropyltriethoxysilane (APTES)-modified TiO2 nanomaterials obtained by solvothermal modification under elevated pressure, followed by calcination in an argon atmosphere at 800-1000 °C, is presented for the first time. The presence of silicon and carbon in the APTES/TiO2 photocatalysts contributed to the effective delay of the anatase-to-rutile phase transformation and the growth of the crystallites size of both polymorphous forms of TiO2 during heating. Thus, the calcined APTES-modified TiO2 exhibited higher pore volume and specific surface area compared with the reference materials. The change of TiO2 surface charge from positive to negative after the heat treatment increased the adsorption of the methylene blue compound. Consequently, due to the blocking of active sites on the TiO2 surface, the adsorption process negatively affected the photocatalytic properties. All calcined photocatalysts obtained after modification via APTES showed a higher dye decomposition degree than the reference samples. For all 3 modifier concentrations tested, the best photoactivity was noted for nanomaterials calcined at 900 °C due to a higher specific surface area than materials calcined at 1000 °C, and a larger number of active sites available on the TiO2 surface compared with samples annealed at 800 °C. It was found that the optimum concentration for TiO2 modification, at which the highest dye decomposition degree was noted, was 500 mM.

ZnO/Carbon Spheres with Excellent Regenerability for Post-Combustion CO2 Capture.

This paper examines the synthesis of the ZnO/carbon spheres composites using resorcinol-formaldehyde resin as a carbon source and zinc nitrate as a zinc oxide source in a solvothermal reactor heated with microwaves. The influence of activation with potassium oxalate and modification with zinc nitrate on the physicochemical properties of the obtained materials and CO2 adsorption capacity was investigated. It was found that in the case of nonactivated material as well as activated materials, the presence of zinc oxide in the carbon matrix had no effect or slightly increased the values of CO2 adsorption capacity. Only for the material where the weight ratio of carbon:zinc was 2:1, the decrease of CO2 adsorption capacity was reported. Additionally, CO2 adsorption experiments on nonactivated carbon spheres and those activated with potassium oxalate with different amounts of zinc nitrate were carried out at 40 °C using thermobalance. The highest CO2 adsorption capacity at temperature 40 °C (2.08 mmol/g adsorbent) was achieved for the material after activation with potassium oxalate with the highest zinc nitrate content as ZnO precursor. Moreover, repeated adsorption/desorption cycle experiments revealed that the as-prepared carbon spheres were very good CO2 adsorbents, exhibiting excellent cyclic stability with a performance decay of less than 10% over up to 25 adsorption-desorption cycles.

Effect of APTES modified TiO2 on antioxidant enzymes activity secreted by Escherichia coli and Staphylococcus epidermidis.

In this work, the impact of APTES-modified TiO2 photocatalysts on antioxidant enzymes (catalase and superoxide dismutase) activity secreted by bacteria was presented. Microbial tests has been examined using Escherichia coli (ATCC 29425) and Staphylococcus epidermidis (ATCC 49461) as model organisms. It was found that APTES-TiO2 affected the activity of antioxidant enzymes. Additionally, obtained APTES-TiO2 photocatalysts were capable of total E. coli and S. epidermidis inactivation under artificial solar light irradiation. The sample modified with the concentration of APTES equals 300 mM (TiO2-4h-120°C-300mM) showed the strongest photocatalytic activity toward both bacteria species. The two-stage photocatalytic mechanism of bacteria response to photocatalysts was proposed.

A New Preparation Method of Cement with Photocatalytic Activity.

The studies of some mechanical properties and photocatalytic activity of new cements with photocatalytic activity are presented. The new building materials were obtained by addition of semi-product from titanium white production. Semi-product was calcined at 300 and 600 °C for one, three, and five hours and then this material was added to cement matrix in an amount of 1 and 3 wt.%. New materials were characterized by measuring the flexural and compressive strength and the initial and the final setting time. The photocatalytic activity was tested during NOx photooxidation. The cement with photocatalytic activity was also characterized by sulphur content measurements. The measurement of reflectance percentage of TiO2-loaded cements in comparison with pristine cement and TiO2 photocatalyst calcined at 600 °C were also performed. It should be emphasized that although in some cases, the addition of photocatalyst reduced the flexural and the compressive strength of the modified cements, these values were still within the norm PN-EN 197-1:2012. It was also found that the initial and the final setting time is connected with the crystal size of anatase, and the presence of larger crystals significantly delays of the setting time. This was probably caused by a water adsorption on the surface of anatase crystals.

Photocatalytic oxidation of nitric oxide over AgNPs/TiO2-loaded carbon fiber cloths.

Series of AgNPs/TiO2-loaded carbon fiber cloth (CFC) composites were prepared by incorporation of pristine TiO2 and three AgNPs-modified TiO2 additives onto the surface of four commercial CFCs. AgNPs/TiO2 photocatalysts were synthesized by the wet impregnation method, including NaBH4 reduction of silver ions. The silver content in the modified photocatalyst was assessed by inductively coupled plasma optical emission spectrometry (ICP-OES) as well as XRD analysis. It can be indicated that silver was successfully reduced to Ag nanoparticles what was confirmed by UV-Vis/DRS as well as XRD methods. The photocatalytic activity of the AgNPs/TiO2-loaded CFCs was evaluated during the photocatalytic oxidation (PCO) tests of nitric oxide (NO) acting as a model air contaminant under UV light. It was found that the highest NO removal rate was observed for the AgNPs/TiO2-loaded CFC material containing 3.70 wt% of AgNPs. Modification of TiO2 with AgNPs stabilized the photocatalytic efficiency of the composites during 5 as well as 24 consecutive NO photooxidation cycles. It was also concluded that the presence of AgNPs was a key factor responsible for hindering NO2 formation.

Photocatalytic Activity and Mechanical Properties of Cements Modified with TiO2/N.

In this paper, studies of the mechanical properties and photocatalytic activity of new photoactive cement mortars are presented. The new building materials were obtained by the addition of 1, 3, and 5 wt % (based on the cement content) of nitrogen-modified titanium dioxide (TiO2/N) to the cement matrix. Photocatalytic active cement mortars were characterized by measuring the flexural and the compressive strength, the hydration heat, the zeta potential of the fresh state, and the initial and final setting time. Their photocatalytic activity was tested during NOx decomposition. The studies showed that TiO2/N gives the photoactivity of cement mortars during air purification with an additional positive effect on the mechanical properties of the hardened mortars. The addition of TiO2/N into the cement shortened the initial and final setting time, which was distinctly observed using 5 wt % of the photocatalyst in the cement matrix.

Bacterial Inactivation on Concrete Plates Loaded with Modified TiO2 Photocatalysts under Visible Light Irradiation.

The antibacterial activity of concrete plates loaded with various titania photocatalysts was investigated. The target in bacteria testing was Escherichia coli K12. The presence of photocatalysts in the concrete matrix at a dose of 10 wt.% improved the antibacterial properties, which became significant depending on the type of the added photocatalyst. Total inactivation of E. coli irradiated under artificial solar light was observed on the concrete plates loaded with the following photocatalysts: TiO2/N,CMeOH-300, TiO2/N,CEtOH-100, TiO2/N,CisoPrOH-100 and TiO2/N-300. The modified Hom disinfection kinetic model was found as a best-fit model for the obtained results. The presence of nitrogen and carbon in the photocatalysts structure, as well as crystallite size, surface area and porosity, contributed to the increase of antibacterial properties of concrete plates.

Assessment of the Suitability of the One-Step Hydrothermal Method for Preparation of Non-Covalently/Covalently-Bonded TiO2/Graphene-Based Hybrids.

A hybrid nanocomposites containing nanocrystalline TiO2 and graphene-related materials (graphene oxide or reduced graphene oxide) were successfully prepared by mechanical mixing and the hydrothermal method in the high-pressure atmosphere. The presented X-ray photoelectron spectroscopy (XPS) study and quantitative elemental analysis confirm similar content of carbon in graphene oxide GO (52 wt% and 46 wt%, respectively) and reduced graphene oxide rGO (92 wt% and 98 wt%, respectively). No chemical interactions between TiO2 and GO/rGO was found. TiO2 nanoparticles were loaded on GO or rGO flakes. However, Fourier transform infrared-diffuse reflection spectroscopy (FTIR/DRS) allowed finding peaks characteristic of GO and rGO. XPS study shows that since the concentration of TiO2 in the samples was no less than 95 wt%, it was assumed that the interactions between TiO2 and graphene should not influence the lower layers of titanium atoms in the TiO2 and they occurred as Ti4+ ions. Hydrothermal treatment at 200 °C did not cause the reduction of GO to rGO in TiO2-GO nanocomposites. In general, the one-step hydrothermal method must be considered to be inefficient for preparation of chemically-bonded composites synthesized from commercially available TiO2 and unfunctionalized graphene sheets obtained from graphite powder.

Antibacterial properties of TiO2 modified with reduced graphene oxide.

In this paper, the antibacterial activity of titanium dioxide modified with reduced graphene oxide (rGO) was presented. TiO2/rGO photocatalysts were prepared by the hydrothermal method under elevated pressure at 180°C and heated at 100°C in Ar flow. The obtained photocatalysts were characterized by means of XRD, FTIR/DRS, UV-vis/DR, Raman spectroscopy and scanning electron microscopy (SEM). The carbon content was also examined. FTIR/DRS and Raman analysis confirmed the presence of rGO in the TiO2 structure, suggesting a successful modification. The antimicrobial photoactivity of photocatalysts was conducted against E. coli under an artificial solar light. The results show that all TiO2/rGO photocatalysts exhibited an antibacterial activity higher than unmodified TiO2. The best result was found for sample with 1.5wt% additive of reduced graphene oxide. In this case, total inactivation of E. coli was noticed after 75min of irradiation. It was found that the presence of rGO in sample improves the antimicrobial activity.

Comparison of methods for evaluation of the bactericidal activity of copper-sputtered surfaces against methicillin-resistant Staphylococcus aureus.

Bacteria can survive on hospital textiles and surfaces, from which they can be disseminated, representing a source of health care-associated infections (HCAIs). Surfaces containing copper (Cu), which is known for its bactericidal properties, could be an efficient way to lower the burden of potential pathogens. The antimicrobial activity of Cu-sputtered polyester surfaces, obtained by direct-current magnetron sputtering (DCMS), against methicillin-resistant Staphylococcus aureus (MRSA) was tested. The Cu-polyester microstructure was characterized by high-resolution transmission electron microscopy to determine the microstructure of the Cu nanoparticles and by profilometry to assess the thickness of the layers. Sputtering at 300 mA for 160 s led to a Cu film thickness of 20 nm (100 Cu layers) containing 0.209% (wt/wt) polyester. The viability of MRSA strain ATCC 43300 on Cu-sputtered polyester was evaluated by four methods: (i) mechanical detachment, (ii) microcalorimetry, (iii) direct transfer onto plates, and (iv) stereomicroscopy. The low efficacy of mechanical detachment impeded bacterial viability estimations. Microcalorimetry provided only semiquantitative results. Direct transfer onto plates and stereomicroscopy seemed to be the most suitable methods to evaluate the bacterial inactivation potential of Cu-sputtered polyester surfaces, since they presented the least experimental bias. Cu-polyester samples sputtered for 160 s by DCMS were further tested against 10 clinical MRSA isolates and showed a high level of bactericidal activity, with a 4-log(10) reduction in the initial MRSA load (10(6) CFU) within 1 h. Cu-sputtered polyester surfaces might be of use to prevent the transmission of HCAI pathogens.