1H NMR characterization of the product from single solid-phase resin beads using capillary NMR flow probes.

A capillary NMR flow probe was designed to generate high-resolution (1)H NMR spectra at 600 MHz from the cleaved product of individual 160-microm Tentagel combinatorial chemistry beads. By injecting a dissolved sample sandwiched between an immiscible, perfluorinated organic liquid directly into the probe, NMR spectra of the product cleaved from single beads were acquired in just 1 h of spectrometer time without diffusional dilution. Sample handling efficiency on the single bead scale was comparable to that obtained with a bulk sample. Using the relative intensity of the DMSO-d(5)H versus the analyte signals in a fully relaxed CPMG spectrum, the amount of product cleaved from a single bead was determined to be 540+/-170 pmol in one of the samples. Following the NMR data collection, the samples were examined with electrospray ionization mass spectrometry to provide additional structural information. By coupling with microliter-volume fluidic capabilities, the capillary flow probe described here will enable multidimensional characterization of single solid-phase resin products in an online manner.

Union of capillary high-performance liquid chromatography and microcoil nuclear magnetic resonance spectroscopy applied to the separation and identification of terpenoids.

This paper describes the first coupling of a commercial capillary HPLC system with a diode array spectrophotometric detector and a custom-built nuclear magnetic resonance (NMR) flow microprobe. The eluent from a 3-microm diameter C18 HPLC column is linked to a 500 MHz 1H-NMR microcoil probe with an observe volume of 1.1 microl. The separation and structurally-rich detection of a mixture of terpenoids under both isocratic and gradient solvent elution conditions is presented. The lowest limits of detection yet reported for capillary HPLC on-line measurement (i.e., 37 ng for alpha-pinene) are achieved with this system. The complementary nature of diode array and NMR detection allows stopped-flow data collection from analytes which would otherwise go unnoticed in continuous-flow NMR. Moreover, stopped-flow NMR data is presented for the detection of a trace (sub-nmol) impurity in the sample mixture. Since NMR signals degrade and shift during solvent gradients, flow injection analysis studies are conducted with injected solvent plugs differing in mobile phase composition. The NMR signal degradation accompanying these injections is largely due to the variance in chemical shift with the solvent composition rather than to changes in magnetic susceptibility of the solvent. Characterization of such effects enables the development of improved NMR probes for the coupling of capillary HPLC and NMR.

Monitoring temperature changes in capillary electrophoresis with nanoliter-volume NMR thermometry.

Nanoliter-volume proton nuclear magnetic resonance (NMR) spectroscopy is used to monitor the electrolyte temperature during capillary electrophoresis (CE). By measuring the shift in the proton resonance frequency of the water signal, the intracapillary temperature can be recorded noninvasively with subsecond temporal resolution and spatial resolution on the order of 1 mm. Thermal changes of more than 65 degrees C are observed under both equilibrium and nonequilibrium conditions for typical CE separation conditions. Several capillary and buffer combinations are examined with external cooling by both liquid and air convection. Additionally, NMR thermometry allows nonequilibrium temperatures in analyte bands to be monitored during a separation. As one example, a plug of 1 mM NaCl is injected into a capillary filled with 50 mM borate buffer. Upon reaching the NMR detector, the temperature in the NaCl band is more than 20 degrees C higher than the temperature in the surrounding buffer. Such observations have direct applicability to a variety of studies, including experiments which utilize sample stacking and isotachophoresis.

Nanoliter-volume 1H NMR detection using periodic stopped-flow capillary electrophoresis.

Recent advances in the analysis of nanoliter volumes using 1H NMR microcoils have led to the application of microcoils as detectors for capillary electrophoresis (CE). Custom NMR probes consisting of 1-mm-long solenoidal microcoils are fabricated from 50-micron diameter wire wrapped around capillaries to create nanoliter-volume detection cells. For geometries in which the capillary and static magnetic field are not parallel, the electrophoretic current induces a magnetic field gradient which degrades the spectroscopic information obtainable from CE/NMR. To reduce this effect and allow longer analyte observation times, the electrophoretic voltage is periodically interrupted so that 1-min high-resolution NMR spectra are obtained for every 15 s of applied voltage. The limits of detection (LODs; based on S/N = 3) for CE/NMR for arginine are 57 ng (330 pmol; 31 mM) and for triethylamine (TEA) are 9 ng (88 pmol; 11 mM). Field-amplified stacking is used for sample preconcentration. As one example, a 290-nL injection of a mixture of arginine and TEA both at 50 mM (15 nmol of each injected) is stacked severalfold for improved concentration LODs while achieving a separation efficiency greater than 50,000. Dissolving a sample in a mixture of 10% H2O/90% D2O allows H2O to serve as the nearly ideal neutral tracer and allows direct observation of the parabolic and flat flow profiles associated with gravimetric and electrokinetic injection, respectively. The unique capabilities of CE and the rich spectral information provided by NMR spectroscopy combine to yield a valuable analytical tool, especially in the study of mass-limited samples.

High-resolution microcoil NMR for analysis of mass-limited, nanoliter samples.

An improved nanoliter-volume NMR probe design places the microcoil and capillary at the magic angle (57.7 degrees) with respect to the external magnetic field. Using an NMR probe which requires a total sample volume of just 200 nL, high-resolution 300-MHz 1H-NMR spectra (line width, 0.6 Hz) are presented of 10 mM alpha-bag cell peptide for an observe quantity of 45 ng (50 pmol in 5 nL). For the volume of sample inside the microcoil (the observe volume, Vobs), the 3 sigma limit of detection (LOD) is 9 ng (10 pmol, 2mM) for data obtained in 15 h. To reduce the data acquisition time, a probe with a greater Vobs is developed. As an example of a rapid, mass-limited analysis, a concentration corresponding to 400 ng of menthol dissolved in Vobs = 31 nL (82.6 mM) yields a spectrum in 9 min (LOD = 6.9 ng, 44 pmol, 1.4 mM). To illustrate improvements in concentration sensitivity, a spectrum is acquired in 45 min for 400 ng of menthol dissolved in a total sample volume of 200 nL (12.8 mM). Compared to a commercial nanoprobe for the same mass of menthol, these two examples reduce data acquisition time by at least 95%. Both model compounds demonstrate substantially improved concentration LODs compared to those obtained in previous high-resolution, microcoil NMR work. These advances illustrate the utility of enhanced sensitivity provided by NMR microcoils applied to nanoliter volumes of mass-limited samples.

Philip Herries Gregory 1907-1986: pioneer aerobiologist, versatile mycologist.

Philip Gregory pioneered aerobiology as a topic for research, drawing together inputs from many disciplines to contribute to better understanding of fungal spore dispersal, plant disease epidemiology, and allergy. In childhood, he was interested in natural history and meteorology and frequently suffered from asthma. Initially, he worked with dermatophytes in Winnipeg, where he was influenced by Buller. Returning to Britain, he investigated the epidemiology first of flower bulb diseases and then of potato virus diseases, noting the occurrence of disease gradients in crops. He developed theories of spore dispersal during wartime air-raid duties and published these in his classic paper of 1945. The remainder of his career was largely spent obtaining data in support of his theories of spore dispersal and disease gradients, on understanding splash dispersal, in identifying the cause of farmer's lung disease, and in his retirement, in elucidating the epidemiology of black pod disease of cocoa in Nigeria.

Farmer's lung: thermophilic actinomycetes as a source of "farmer's lung hay" antigen. 1963.

Mouldy hay was produced in the laboratory by sterilising good hay, inoculating with aqueous suspensions of microorganisms, and incubating at 40 degrees or 60 degrees C. Extracts were tested for presence of farmer's lung hay (F.L.H.) antigen by agar-gel double-diffusion and immunoelectrophoresis tests against sixteen to twenty sera from patients with farmer's lung. F.L.H. antigen developed in hay after: (1) inoculating with mixed microbial suspensions from antigenically active hay; (2) inoculation with mixed suspensions of pure cultures of thermophilic actinomycetes, after raising the pH of the hay to 70 either by prior inoculation with fungi or by infiltration with ammonia vapour; and (3) inoculation at pH 70 with pure cultures of Thermopolyspora polyspora or with Micromonospora vulgaris. F.L.H. antigen did not develop in hay after inoculation with fungi only, or with six other actinomycetes tested, or after prior heating (though some sera reacted to fungal antigens in all these extracts). T. polyspora is the richest source yet found of F.L.H. antigen, and inhalation of an extract by affected subjects produces some of the features of farmer's lung. Pure cultures can produce F.L.H. antigen on artificial media without hay. Spores and mycelium are rich in F.L.H. antigen, and inhalation of the spores may play a part in farmer's lung disease. Other antigens relevant to farmer's lung may be found in other actinomycetes, not yet cultured.