Synergistic Effects of Surface Coating and Bulk Doping in Ni-Rich Lithium Nickel Cobalt Manganese Oxide Cathode Materials for High-Energy Lithium Ion Batteries.

Ni-rich layered oxide cathodes are promising candidates to satisfy the increasing energy demand of lithium-ion batteries for automotive applications. Thermal and cycling stability issues originating from increasing Ni contents are addressed by mitigation strategies such as elemental bulk substitution ("doping") and surface coating. Although both approaches separately benefit the cycling stability, there are only few reports investigating the combination of two of such approaches. Herein, the combination of Zr as common dopant in commercial materials with effective Li2 WO4 and WO3 coatings was investigated with special focus on the impact of different material processing conditions on structural parameters and electrochemical performance in nickel-cobalt-manganese (NCM) || graphite cells. Results indicated that the Zr4+ dopant diffusing to the surface during annealing improved the electrochemical performance compared to samples without additional coatings. This work emphasizes the importance to not only investigate the effect of individual dopants or coatings but also the influences between both.

Influence of Iron Sulfide Nanoparticle Sizes in Solid-State Batteries*.

Given the inherent performance limitations of intercalation-based lithium-ion batteries, solid-state conversion batteries are promising systems for future energy storage. A high specific capacity and natural abundancy make iron disulfide (FeS2 ) a promising cathode-active material. In this work, FeS2 nanoparticles were prepared solvothermally. By adjusting the synthesis conditions, samples with average particle diameters between 10 nm and 35 nm were synthesized. The electrochemical performance was evaluated in solid-state cells with a Li-argyrodite solid electrolyte. While the reduction of FeS2 was found to be irreversible in the initial discharge, a stable cycling of the reduced species was observed subsequently. A positive effect of smaller particle dimensions on FeS2 utilization was identified, which can be attributed to a higher interfacial contact area and shortened diffusion pathways inside the FeS2 particles. These results highlight the general importance of morphological design to exploit the promising theoretical capacity of conversion electrodes in solid-state batteries.

High-speed solid state fluorination of Nb2O5 yields NbO2F and Nb3O7F with photocatalytic activity for oxygen evolution from water.

Solid state reactions are slow because the diffusion of atoms or ions through the reactant, intermediate and crystalline product phases is the rate-limiting step. This requires days or even weeks of high temperature treatment, and consumption of large amounts of energy. We employed spark-plasma sintering, an engineering technique that is used for high-speed consolidation of powders with a pulsed electric current passing through the sample to carry out the fluorination of niobium oxide in minute intervals. The approach saves time and large amounts of waste energy. Moreover, it allows the preparation of fluorinated niobium oxides on a gram scale using poly(tetrafluoroethylene) (®Teflon) scrap and without toxic chemicals. The synthesis can be upscaled easily to the kg range with appropriate sintering equipment. Finally, NbO2F and Nb3O7F prepared by spark plasma sintering show significant photoelectrocatalytic (PEC) oxygen evolution from water in terms of photocurrent density and incident photon-to-current efficiency (% IPCE), whereas NbO2F and Nb3O7F prepared by conventional high temperature chemistry show little to no PEC response. Our study is a proof of concept for the quick, clean and energy saving production of valuable photocatalysts from plastic waste.

A Generalized Method for High-Speed Fluorination of Metal Oxides by Spark Plasma Sintering Yields Ta3 O7 F and TaO2 F with High Photocatalytic Activity for Oxygen Evolution from Water.

A general method to carry out the fluorination of metal oxides with poly(tetrafluoroethylene) (PTFE, Teflon) waste by spark plasma sintering (SPS) on a minute scale with Teflon is reported. The potential of this new approach is highlighted by the following results. i) The tantalum oxyfluorides Ta3 O7 F and TaO2 F are obtained from plastic scrap without using toxic or caustic chemicals for fluorination. ii) Short reaction times (minutes rather than days) reduce the process time the energy costs by almost three orders of magnitude. iii) The oxyfluorides Ta3 O7 F and TaO2 F are produced in gram amounts of nanoparticles. Their synthesis can be upscaled to the kg range with industrial sintering equipment. iv) SPS processing changes the catalytic properties: while conventionally prepared Ta3 O7 F and TaO2 F show little catalytic activity, SPS-prepared Ta3 O7 F and TaO2 F exhibit high activity for photocatalytic oxygen evolution, reaching photoconversion efficiencies up to 24.7% and applied bias to photoconversion values of 0.86%. This study shows that the materials properties are dictated by the processing which poses new challenges to understand and predict the underlying factors.

Gram-scale selective synthesis of WO3-x nanorods and (NH4)xWO3 ammonium tungsten bronzes with tunable plasmonic properties.

Localized surface plasmon resonance properties in unconventional materials like metal oxides or chalcogenide semiconductors have been studied for use in signal detection and analysis in biomedicine and photocatalysis. We devised a selective synthesis of the tungsten oxides WO3-x and (NH4)xWO3 with tunable plasmonic properties. We selectively synthesized WO3-x nanorods with different aspect ratios and hexagonal tungsten bronzes (NH4)xWO3 as truncated nanocubes starting from ammonium metatungstate (NH4)6H2W12O40·xH2O. Both particles form from the same nuclei at temperatures >200 °C; monomer concentration and surfactant ratio are essential variables for phase selection. (NH4)xWO3 was the preferred reaction product only for fast heating rates (25 K min-1), slow stirring speeds (∼150 rpm) and high precursor concentrations. A proton nuclear magnetic resonance (1H-NMR) spectroscopic study of the reaction mechanism revealed that oleyl oleamide, formed from oleic acid and oleylamine upon heating, is a key factor for the selective formation of WO3-x nanorods. Since oleic acid and oleylamine are standard surfactants for the wet chemical synthesis of many metal and oxide nanoparticles, the finding that oleyl oleamide acts as a chemically active reagent above 250 °C may have implications for many nanoparticle syntheses. Oriented attachment of polyoxotungstate anions is proposed as a model to rationalize phase selectivity. Magic angle spinning (MAS) 1H-NMR and powder X-ray diffraction (PXRD) studies of the bronze after annealing under (non)inert conditions revealed an oxidative phase transition. WO3-x and (NH4)xWO3 show a strong plasmon absorption for near infra-red light between 800 and 3300 nm. The maxima of the plasmon bands shift systematically with the nanocrystal aspect ratio.