Surface Hydrides on Fe2P Electrocatalyst Reduce CO2 at Low Overpotential: Steering Selectivity to Ethylene Glycol.

Development of efficient electrocatalysts for the CO2 reduction reaction (CO2RR) to multicarbon products has been constrained by high overpotentials and poor selectivity. Here, we introduce iron phosphide (Fe2P) as an earth-abundant catalyst for the CO2RR to mainly C2-C4 products with a total CO2RR Faradaic efficiency of 53% at 0 V vs RHE. Carbon product selectivity is tuned in favor of ethylene glycol formation with increasing negative bias at the expense of C3-C4 products. Both Grand Canonical-DFT (GC-DFT) calculations and experiments reveal that *formate, not *CO, is the initial intermediate formed from surface phosphino-hydrides and that the latter form ionic hydrides at both surface phosphorus atoms (H@Ps) and P-reconstructed Fe3 hollow sites (H@P*). Binding of these surface hydrides weakens with negative bias (reactivity increases), which accounts for both the shift to C2 products over higher C-C coupling products and the increase in the H2 evolution reaction (HER) rate. GC-DFT predicts that phosphino-hydrides convert *formate to *formaldehyde, the key intermediate for C-C coupling, whereas hydrogen atoms on Fe generate tightly bound *CO via sequential PCET reactions to H2O. GC-DFT predicts the peak in CO2RR current density near -0.1 V is due to a local maximum in the binding affinity of *formate and *formaldehyde at this bias, which together with the more labile C2 product affinity, accounts for the shift to ethylene glycol and away from C3-C4 products. Consistent with these predictions, addition of exogenous CO is shown to block all carbon product formation and lower the HER rate. These results demonstrate that the formation of ionic hydrides and their binding affinity, as modulated by the applied potential, controls the carbon product distribution. This knowledge provides new insight into the influence of hydride speciation and applied bias on the chemical reaction mechanism of CO2RR that is relevant to all transition metal phosphides.

Water Oxidation by the [Co4O4(OAc)4(py)4](+) Cubium is Initiated by OH(-) Addition.

The cobalt cubium Co4O4(OAc)4(py)4(ClO4) (1A(+)) containing the mixed valence [Co4O4](5+) core is shown by multiple spectroscopic methods to react with hydroxide (OH(-)) but not with water molecules to produce O2. The yield of reaction products is stoichiometric (>99.5%): 41A(+) + 4OH(-) → O2 + 2H2O + 41A. By contrast, the structurally homologous cubium Co4O4(trans-OAc)2(bpy)4(ClO4)3, 1B(ClO4)3, produces no O2. EPR/NMR spectroscopies show clean conversion to cubane 1A during O2 evolution with no Co(2+) or Co3O4 side products. Mass spectrometry of the reaction between isotopically labeled µ-(16)O(bridging-oxo) 1A(+) and (18)O-bicarbonate/water shows (1) no exchange of (18)O into the bridging oxos of 1A(+), and (2) (36)O2 is the major product, thus requiring two OH(-) in the reactive intermediate. DFT calculations of solvated intermediates suggest that addition of two OH(-) to 1A(+) via OH(-) insertion into Co-OAc bonds is energetically favored, followed by outer-sphere oxidation to intermediate [1A(OH)2](0). The absence of O2 production by cubium 1B(3+) indicates the reactive intermediate derived from 1A(+) requires gem-1,1-dihydoxo stereochemistry to perform O-O bond formation. Outer-sphere oxidation of this intermediate by 2 equiv of 1A(+) accounts for the final stoichiometry. Collectively, these results and recent literature (Faraday Discuss., doi:10.1039/C5FD00076A and J. Am. Chem. Soc. 2015, 137, 12865-12872) validate the [Co4O4](4+/5+) cubane core as an intrinsic catalyst for oxidation of hydroxide by an inner-sphere mechanism.

MoS2-an integrated protective and active layer on n(+)p-Si for solar H2 evolution.

A new MoS2 protected n(+)p-junction Si photocathode for the renewable H2 evolution is presented here. MoS2 acts as both a protective and an electrocatalytic layer, allowing H2 evolution at 0 V vs. RHE for more than 5 days. Using a MoSx surface layer decreases the overpotential for H2 evolution by 200 mV.

A high-porosity carbon molybdenum sulphide composite with enhanced electrochemical hydrogen evolution and stability.

This work describes a highly active and stable acid activated carbon fibre and amorphous MoS(x) composite hydrogen evolution catalyst. The increased electrochemical-surface area is demonstrated to cause increased catalyst electrodeposition and activity. These composite electrodes also show an improved stability towards the mechanical degradation of the MoS(x) catalyst.

Using TiO2 as a conductive protective layer for photocathodic H2 evolution.

Surface passivation is a general issue for Si-based photoelectrodes because it progressively hinders electron conduction at the semiconductor/electrolyte interface. In this work, we show that a sputtered 100 nm TiO(2) layer on top of a thin Ti metal layer may be used to protect an n(+)p Si photocathode during photocatalytic H(2) evolution. Although TiO(2) is a semiconductor, we show that it behaves like a metallic conductor would under photocathodic H(2) evolution conditions. This behavior is due to the fortunate alignment of the TiO(2) conduction band with respect to the hydrogen evolution potential, which allows it to conduct electrons from the Si while simultaneously protecting the Si from surface passivation. By using a Pt catalyst the electrode achieves an H(2) evolution onset of 520 mV vs NHE and a Tafel slope of 30 mV when illuminated by the red part (λ > 635 nm) of the AM 1.5 spectrum. The saturation photocurrent (H(2) evolution) was also significantly enhanced by the antireflective properties of the TiO(2) layer. It was shown that with proper annealing conditions these electrodes could run 72 h without significant degradation. An Fe(2+)/Fe(3+) redox couple was used to help elucidate details of the band diagram.

Hydrogen production using a molybdenum sulfide catalyst on a titanium-protected n(+)p-silicon photocathode.

A low-cost substitute: A titanium protection layer on silicon made it possible to use silicon under highly oxidizing conditions without oxidation of the silicon. Molybdenum sulfide was electrodeposited on the Ti-protected n(+)p-silicon electrode. This electrode was applied as a photocathode for water splitting and showed a greatly enhanced efficiency.

A general route for RuO2 deposition on metal oxides from RuO4.

A novel method for the deposition of RuO(2) from RuO(4)(g) on diverse metal oxides has been developed by grafting dopamine onto the otherwise un-reactive metal oxide surface. Oxygen evolution reaction on TiO(2) and the photoelectrochemical improvement of WO(3) by deposition of RuO(2) are just a few examples where this novel deposition method can be used.