High-performance flexible thermoelectric modules based on high crystal quality printed TiS2/hexylamine.

Printed electronics implies the use of low-cost, scalable, printing technologies to fabricate electronic devices and circuits on flexible substrates, such as paper or plastics. The development of this new electronic is currently expanding because of the emergence of the internet-of-everything. Although lot of attention has been paid to functional inks based on organic semiconductors, another class of inks is based on nanoparticles obtained from exfoliated 2D materials, such as graphene and metal sulfides. The ultimate scientific and technological challenge is to find a strategy where the exfoliated nanoparticle flakes in the inks can, after solvent evaporation, form a solid which displays performances equal to the single crystal of the 2D material. In this context, a printed layer, formed from an ink composed of nano-flakes of TiS2 intercalated with hexylamine, which displays thermoelectric properties superior to organic intercalated TiS2 single crystals, is demonstrated for the first time. The choice of the fraction of exfoliated nano-flakes appears to be a key to the forming of a new self-organized layered material by solvent evaporation. The printed layer is an efficient n-type thermoelectric material which complements the p-type printable organic semiconductors The thermoelectric power factor of the printed TiS2/hexylamine thin films reach record values of 1460 µW m-1 K-2 at 430 K, this is considerably higher than the high value of 900 µW m-1 K-2 at 300 K reported for a single crystal. A printed thermoelectric generator based on eight legs of TiS2 confirms the high-power factor values by generating a power density of 16.0 W m-2 at ΔT = 40 K.

Synthesis of transparent vertically aligned TiO2 nanotubes on a few-layer graphene (FLG) film.

Novel transparent 1D-TiO(2)/few-layer graphene electrodes are realised by the anodic growth of vertically aligned TiO(2) nano-tubes on a few-layer graphene film coated on a glass substrate.

Efficient synthesis of dimethyl ether over HZSM-5 supported on medium-surface-area beta-SiC foam.

In this study, we aimed to produce a highly selective and stable catalyst for the production of dimethyl ether by methanol dehydration. The activities were compared of different active phases of the employed system, zeolite HZSM-5 or gamma-alumina, supported on silicon carbide as foam, and it was found that the supported zeolite catalysts are more active than and as selective as the alumina-based catalysts. The as-prepared zeolite/SiC composites reveal good stability in long-term tests in the presence or absence of steam. The high stability is attributed to the presence of highly dispersed micrometer-sized zeolite particles, which make the active sites more accessible to the reactants and promote the quick transfer of the desired product, dimethyl ether, out of the catalyst bed, minimizing deactivation of the catalyst.

3D electron microscopy study of metal particles inside multiwalled carbon nanotubes.

The location of palladium nanoparticles on and inside the multiwalled carbon nanotubes channel is presented for the first time using electron tomography (3D TEM). The palladium salt precursor was rapidly sucked inside the nanotube channel by means of capillarity that is favored by the hydrophilic character of the tube wall after acidic treatment at low temperature. Statistical analysis indicates that the palladium particles were well dispersed and the palladium particle size was relatively homogeneous, ranging from 3 to 4 nm regardless of their location within the nanotube, within the resolution limit of the technique for our experimental conditions, i.e., about 2 nm. Three-dimensional TEM analysis also revealed that introduction of foreign elements inside the tube channel is strongly influenced by the diameter of the tube inner channel, i.e., easy filling seems to occur with a tube channel >or=30 nm , whereas with tubes having a smaller channel (<15 nm), almost no filling by capillarity occurred leading to the deposition of the metal particles only on the outer wall of the tube.

Autoassembly of nanofibrous zeolite crystals via silicon carbide substrate self-transformation.

ZSM-5 zeolite nanofibers with a size of 90 nm and lengths up to several micrometers were prepared via in-situ silicon carbide support self-transformation. The morphology and aggregation degree of these zeolite nanofibers could be modified by adjusting the pH conditions, the nature of the mineralizer (OH- or F-), or the synthesis duration. The novelty consists of the preparation of zeolite nanowires without the use of any organogelating agent, along with controlled macroscopic shapes (extrudates, foam monolith) for direct use as a structured reactor. Finally, these materials are catalytically active in the conversion of methanol to gasoline range hydrocarbons (MTG process) and hence exhibit the typical solid acidity of zeolitic materials.

Quantitative measurement of the Brönsted acid sites in solid acids: toward a single-site design of Mo-modified ZSM-5 zeolite.

On the basis of our previous H/D exchange studies devoted to the quantification of the number of Brönsted acid sites in solid acids, we report here an innovative approach to determine both the amount and the localization of Mo atoms inside the Mo/ZSM-5 catalyst, commonly used for the methane dehydroaromatization reaction. The influence of Mo introduction in the MFI framework was studied by means of BET, X-ray diffraction, 27Al magic angle spinning NMR, NH3 temperature-programmed desorption, and H/D isotopic exchange techniques. A dependence was found between the decrease of acidic OH groups and the Mo content. Depending on the Si/Al ratio of the zeolite, i.e., the proximity of two Brönsted acid sites, the Mo atoms substitute a different number of OH groups. Consequently, a chemical structure was proposed to describe the geometry of the Mo complex in the channels of the ZSM-5 zeolite.

Beta zeolite supported on silicon carbide for Friedel-Crafts fixed-bed reactions.

Beta zeolite supported on silicon carbide, with high thermal conductivity and high mechanical strength, was successfully used as an active and stable catalyst for Friedel-Crafts reactions in a fixed bed configuration.