Fluorine-free nanoparticle coatings on cotton fabric: comparing the UV-protective and hydrophobic capabilities of silica vs. silica-ZnO nanostructures.

Robust, hydrophobic woven cotton fabrics were obtained through the sol-gel dip coating of two different nanoparticle (NP) architectures; silica and silica-ZnO. Water repellency values as high as 148° and relatively low tilt angles for fibrous fabrics (12°) were observed, without the need for fluorinated components. In all cases, this enhanced functionality was achieved with the broad retention of water vapor permeability characteristics, i.e., less than 10% decrease. NP formation routes indicated direct bonding interactions in both the silica and silica-ZnO structures. The physico-chemical effects of NP-compatibilizer (i.e., polydimethoxysilane (PDMS) and n-octyltriethoxysilane (OTES) at different ratios) coatings on cotton fibres indicate that compatibilizer-NP interactions are predominantly physical. Whenever photoactive ZnO-containing additives were used, there was a minor decrease in hydrophobic character, but order of magnitude increases in UV-protective capability (i.e., UPF > 384); properties which were absent in non-ZnO-containing samples. Such water repellency and UPF capabilities were stable to both laundering and UV-exposure, resisting the commonly encountered UV-induced wettability transitions associated with photoactive ZnO. These results suggest that ZnO-containing silica NP coatings on cotton can confer both excellent and persistent surface hydrophobicity as well as UV-protective capability, with potential uses in wearables and functional textiles applications.

Influence of Electrospinning Parameters on the Morphology of Electrospun Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) Fibrous Membranes and Their Application as Potential Air Filtration Materials.

A large number of non-degradable materials have severely damaged the ecological environment. Now, people are increasingly pursuing the use of environmentally friendly materials to replace traditional chemical materials. Polyhydroxyalkonates (PHAs) are receiving increasing attention because of the unique biodegradability and biocompatibility they offer. However, the applications of PHAs are still limited due to high production costs and insufficient study. This project examines the optimal electrospinning parameters for the production of PHA-based fibrous membranes for air filtration. A common biodegradable polyester, Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV), was electrospun into a nanofibrous membrane with a well-controlled surface microstructure. In order to produce smooth, bead-free fibers with micron-scale diameters, the effect of the process parameters (applied electric field, solution flow rate, inner diameter of hollow needle, and polymer concentration) on the electrospun fiber microstructure was optimized. The well-defined fibrous structure was optimized at an applied electric field of 20 kV, flow rate of 0.5 mL/h, solution concentration of 12 wt.%, and needle inner diameter of 0.21 mm. The morphology of the electrospun PHBV fibrous membrane was observed by scanning electron microscopy (SEM). Fourier transform infrared (FTIR) and Raman spectroscopy were used to explore the chemical signatures and phases of the electrospun PHBV nanofiber. The ball burst strength (BBS) was measured to assess the mechanical strength of the membrane. The small pore size of the nanofiber membranes ensured they had good application prospects in the field of air filtration. The particle filtration efficiency (PFE) of the optimized electrospun PHBV fibrous membrane was above 98% at standard atmospheric pressure.

The onset of surface-enhanced Raman scattering for single-particle detection of submicroplastics.

Microplastics represent an emerging environmental problem worldwide, raising ecological and food safety concerns. Compared to microplastics, there is growing evidence of an even higher abundance of submicro- and nanoplastics in the environment, but a reliable monitoring method for detecting these smaller-sized plastics is lacking. Herein we presented the application of surface-enhanced Raman scattering (SERS) for this purpose. Particles of polystyrene (PS; 600 nm) were used as the probe analyte. Gold nanourchins (AuNU; 50 nm), i.e. urchin-shaped nanoparticles with irregular spikes around the core, were used as the SERS-active substrate. The effectiveness of SERS on PS was evaluated at a single-particle level with different numbers of AuNU in order to determine the minimum conditions required for the onset of the SERS effect. Our findings suggest that SERS of a single particle of PS can be induced by as few as 1-5 particles of AuNU, and that the use of excitation wavelength at 785 nm is appropriate to meet the red-shifted surface plasmon resonance of AuNU upon aggregation. These specifications provide additional information for the development of SERS-based tools for detecting plastic particles < 1 µm in food and environmental samples.

Effects of temperature and particle concentration on aggregation of nanoplastics in freshwater and seawater.

Microplastics have become a significant environmental problem worldwide. Compared with microplastics, nanoplastics are apparently more abundant and harmful but their environmental processes are less well understood. The fate and ecological impacts of nanoplastics in aquatic environments are largely determined by their aggregation properties, which were investigated here using pure water and artificial seawater prepared in the laboratory, as well as river water and coastal seawater collected from subtropical Hong Kong. The tests were carried out at an environmentally realistic temperature range (15-35 °C) with particle concentrations over four orders of magnitude (0.1-100 mg L-1). Under these experimental conditions, parameters of dynamic light scattering were used to determine the extent of aggregation and colloidal stability of polystyrene nanospheres (nPS), a common test model of nanoplastics. Our results showed that aggregation of nPS was minimal in pure water and river water, but became strong under the ionic strength of artificial seawater and coastal seawater, in which 70 nm nPS could aggregate to > 2000 nm, and this aggregation clearly increased with increase in temperature and particle concentration. The aggregates with increasing size and decreasing colloidal stability were deposited more quickly. Findings from this study imply an increased risk of nanoplastics to marine benthic organisms through the aggregation and deposition processes, particularly in warmer waters.

Nanobubble-assisted scaling inhibition in membrane distillation for the treatment of high-salinity brine.

In this study, we report the use of nanobubbles (NBs) as a simple and facile approach to effectively delay scaling in membrane distillation (MD) during the treatment of highly saline feed (100 g L-1). Unlike conventional gas bubbling in MD for improving the hydrodynamic flow conditions in the feed channel, here we generated air NBs with an average size of 128.81 nm in the feed stream and examined their impact on membrane scaling inhibition during MD operation. Due to their small size, neutral buoyancy, and negative surface charge, NBs remain in suspension for a longer time (14 days), providing homogenous mixing throughout the entire feed water. The MD performance results revealed that severe membrane scaling happened during the DCMD treatment of high salinity brine in the absence of nanobubbles, which dramatically reduced the distillate flux to zero after 13 h. A one-time addition of air NBs in the saline feed significantly reduced salt precipitation and crystal deposition on the PVDF membrane surface, delayed the occurrence of flux decline, prevented membrane wetting, thereby prolonging the effective MD operating time. With similar feed concentration and operating conditions, only 63% flux decline after 98 h operation was recorded in nanobubble-assisted MD. Two key explanations were suggested for the delayed membrane scaling upon addition of air NBs in the MD feed: (1) NB-induced turbulent flow in the feed channel that increases the surface shear forces at the membrane surface, alleviating both temperature and concentration polarization effect, (2) electrostatic attractions of the counterions to the negatively charged NBs, which reduces the availability of these ions in the bulk feed for scale formation.

In Vivo Biodistribution, Clearance, and Biocompatibility of Multiple Carbon Dots Containing Nanoparticles for Biomedical Application.

Current research on the use of carbon dots for various biological systems mainly focuses on the single carbon dots, while particles that contain multiple carbon dots have scarcely been investigated. Here, we assessed multiple carbon dots-crosslinked polyethyleneimine nanoparticles (CDs@PEI) for their in vivo biodistribution, clearance, biocompatibility, and cellular uptake. The in vivo studies demonstrate three unique features of the CDs@PEI nanoparticles: (1) the nanoparticles possess tumor-targeting ability with steady and prolonged retention time in the tumor region. (2) The nanoparticles show hepatobiliary excretion and are clear from the intestine in feces. (3) The nanoparticles have much better biocompatibility than the polyethyleneimine passivated single carbon dots (PEI-CD). We also found that pegylated CDs@PEI nanoparticles can be effectively taken up by the cells, which the confocal laser scanning microscope can image under different excitation wavelengths (at 405, 488, and 800 nm). These prior studies provide invaluable information and new opportunities for this new type of intrinsic photoluminescence nanoparticles in carbon dot-based biomedical applications.

Determination of microplastics in the edible green-lipped mussel Perna viridis using an automated mapping technique of Raman microspectroscopy.

Microplastics are prevalent in marine environments and seafood and thus can easily end up in human diets. This has raised serious concerns worldwide, particularly in Hong Kong where the seafood consumption per capita can be three times higher than the global average. This study focused on the green-lipped mussel Perna viridis, a popular seafood species which is subject to a high risk of contamination by microplastics due to its filter-feeding nature. P. viridis was collected from five mariculture sites in Hong Kong and assessed for its body load of microplastics using an automated Raman mapping approach. Microplastics were found in all sites, with an average of 1.60-14.7 particles per mussel per site, or 0.21-1.83 particles per g wet weight. Polypropylene, polyethylene, polystyrene and polyethylene terephthalate were detected among the microplastics, mainly as fragments or fibres in the size range of 40-1000 µm. It was estimated that through consumption of P. viridis, the population in Hong Kong could ingest up to 10,380 pieces of microplastics per person per year. These estimated rates were high compared to the values reported worldwide, suggesting the potential human health risk of microplastics in Hong Kong and adjacent areas.

Improved Raman spectroscopy-based approach to assess microplastics in seafood.

Microplastics represent an emerging environmental issue and have been found almost everywhere including seafood, raising a great concern about the ecological and human health risks they pose. This study addressed the common technical challenges in the assessment of microplastics in seafood by developing an improved protocol based on Raman spectroscopy and using the green-lipped mussel Perna viridis and the Japanese jack mackerel Trachurus japonicus as the test models. Our findings identified a type of stainless-steel filter membranes with minimal Raman interference, and a combination of chemicals that achieved 99-100% digestion efficiency for both organic and inorganic biomass. This combined chemical treatment reached 90-100% recovery rates for seven types of microplastics, on which the surface modification was considered negligible and did not affect the accuracy of polymer identification based on Raman spectra, which showed 94-99% similarity to corresponding untreated microplastics. The developed extraction method for microplastics was further combined with an automated Raman mapping approach, from which our results confirmed the presence of microplastics in P. viridis and T. japonicus collected from Hong Kong waters. Identified microplastics included polypropylene, polyethylene, polystyrene and poly(ethylene terephthalate), mainly in the form of fragments and fibres. Our protocol is applicable to other biological samples, and provides an improved alternative to streamline the workflow of microplastic analysis for routine monitoring purposes.

Graphene Oxide/Reduced Graphene Oxide Enhanced Noniridescent Structural Colors Based on Silica Photonic Spray Paints with Improved Mechanical Robustness.

In contrast to traditional pigment colors, structural colors have developed a great potential in practical applications, thanks to their unique nonfading and color tunable properties; especially amorphous photonic structures with noniridescent structural colors have attracted considerable attention and their applications have expanded to more fields. Herein, graphene oxide (GO) and reduced graphene oxide (RGO) enhanced noniridescent structural colors with excellent mechanical robustness were established by a time-saving approach named spray coating, which allows for rapid fabrication of angular independent structural colors by spraying different photonic spray paints (PSPs) to ensure color multiplicity that was adjusted by the silica nanoparticles (SiO2 NPs) sizes onto the substrates. The incorporation of poly(methyl methacrylate-butyl acrylate) (PMB) improved the adhesion existing among SiO2 inter-nanoparticles and between SiO2 NPs and the substrates, taking advantages of the low glass transition temperature (Tg) of butyl acrylate derivative polymer and made PMB embedded PSPs coated patterns being imparted with good mechanical robustness and abrasive resistance. The peculiar light adsorption of GO and RGO across visible light spectrum facilitate higher color saturation. The improvement in color saturation of GO and RGO doped PSPs is expected to boost the promising applications in structurally colored paintings, inks and other color-related optical fields.

A Computer Color-Matching Study of Reverse Micellar Dyeing of Wool with Reactive Dyes.

Computer color-matching (CCM) and the levelness of poly(ethylene glycol)-based reverse-micellar dyed wool fabrics in octane and nonane were investigated and compared with a conventional water-based dyeing system. Reflectance curves and calibration curves exhibited no chromatic change and maintained high linearity in both dyeing systems. The linearity of water-dyed calibration curves was slightly higher than that of the reverse-micellar dyed curves. The color yield, in term of K/Ssum values, of solvent-dyed samples was found to be generally higher than that of water-based dyed samples at various calibrated dye concentrations. The concentrations predicted by CCM were close to the theoretical concentrations for both dyeing methods. This indicates that octane- and nonane-assisted reverse-micellar dyeing of wool is able to generate color recipes comparable to the conventional water-based dyeing system. The solvent-dyed samples, measured by the relative unlevelness indices (RUI), exhibit good-to-excellent levelness, which is highly comparable with the water-dyed samples.

Octane-Assisted Reverse Micellar Dyeing of Cotton with Reactive Dyes.

In this study, we investigated the computer colour matching (CCM) of cotton fabrics dyed with reactive dye using the octane-assisted reverse micellar approach. The aim of this study is to evaluate the colour quality and compare the accuracy between CCM forecasting and simulated dyeing produced by conventional water-based dyeing and octane-assisted reverse micellar dyeing. First, the calibration of dyeing databases for both dyeing methods was established. Standard samples were dyed with known dye concentrations. Computer colour matching was conducted by using the colour difference formula of International Commission on Illumination (CIE) L*a*b*. Experimental results revealed that the predicted concentrations were nearly the same as the expected known concentrations for both dyeing methods. This indicates that octane-assisted reverse micellar dyeing system can achieve colour matching as good as the conventional water-based dyeing system. In addition, when comparing the colour produced by the conventional water-based dyeing system and the octane-assisted reverse micellar dyeing system, the colour difference (ΔE) is ≤1, which indicates that the reverse micellar dyeing system could be applied for industrial dyeing with CCM.

Evaluation of resveratrol oxidation in vitro and the crucial role of bicarbonate ions.

Polyphenols can oxidize in culture medium and produce artifacts in cell culture studies. However, the extent and mechanism of the oxidation of resveratrol, a polyphenol abundant in red wine, is unclear. We investigated the oxidation of resveratrol in vitro and the effects of various components of the culture medium on the degradation of resveratrol and the production of H(2)O(2). We found that 96% of resveratrol at a concentration of 200 microM was degraded in Base Modified Eagle Medium after 24 h of incubation at 37 degrees C, producing about 90 microM of H(2)O(2). Including sodium bicarbonate in the medium markedly stimulated resveratrol degradation and H(2)O(2) production. In sum, we found that bicarbonate ions played a crucial role in the oxidative degradation of resveratrol in vitro, and that the degradation of resveratrol can be avoided by withdrawing sodium bicarbonate from the medium. A mechanism for the oxidation of resveratrol is proposed.

Genetic and antigenic analysis of epidemic influenza viruses isolated during 2006-2007 season in Taiwan.

Influenza viruses are some of the most active pathogens in Taiwan. The monitoring influenza activity has been coordinated by the Centers for Diseases Control, Taiwan, and the surveillance is based on integrated clinical and virological surveillance components. Data from sentinel physician networks and other sources, mainly hospitals were collected. During 2006-07 season, a total of 1724 cases of laboratory-confirmed influenza were reported by collaborating laboratories and sentinels, which was five fold higher than during the corresponding part of the 2005-06 season. Of the Taiwan isolates analyzed using post-infection ferret antisera, 1.5% were H1N1 (A/Hi), 21.5% H3N2 (A/H3), and 77.0% influenza B viruses. This reflects the predominance of influenza B viruses during 2006-07 season. In addition, continued antigenic drift was seen with the A/I-B viruses compared with the previous season's reference strains. However, an increasing number of recent A/H3 isolates characterized in our report were amantadine sensitive. Preparation for an influenza pandemic is presently a high priority in Taiwan. Laboratory-based surveillance systems must be timely in order to be effective. The data presented here highlights the need to characterize the circulating strains both antigenically and genetically during regular surveillance. Any contribution of individual genes or gene combinations to usual or unusual epidemic characteristics might thus be identified ensuring that virus strains can be selected for vaccine formulation that will most closely match the circulating viruses.

Characterization of the epidemic influenza B viruses isolated during 2004-2005 season in Taiwan.

To characterize the antigenic and genetic relationships of influenza B viruses isolated during the 2004-2005 season, a total of 11,707 clinical respiratory samples were tested of which 1572 (13.5%) were positive for influenza (463 type A and 1109 type B influenza). Of the type B viruses, 348 isolates collected in different parts of Taiwan were further analyzed. Viruses belonging to both influenza B lineages, B/Yamagata/16/88 (B/Yam) and B/Victoris/2/87 (B/Vic) were detected, although an increasing number of B/Vic lineage isolates was obtained as the season progressed. Recent B/Vic-lineage isolates were found to have additional amino acid substitutions compared to isolates from previous seasons, indicating that viruses of this lineage continue to evolve significantly and may have the capacity to become the dominant influenza B viruses worldwide. Results presented in this report demonstrate that antigenically and genetically distinct viruses within both B/Vic and B/Yam lineages co-circulate and that reassortment among these two lineages occurs frequently contributing to the genetic diversity of the circulating strains.