Analysis and derivation of the marine water quality criteria of phenol for Korean seas.

Marine water quality criteria (WQC) have to be determined prior to the derivation of water quality based effluent limitations (WQBELs) for hazardous and noxious substances (HNS) discharged from marine industrial facilities. In this study, we carried out toxicity tests using ten native marine organisms and analyzed international toxicity data and data tested in this study to derive the WQC of phenol for Korean seas. By converting acute values to chronic ones with ACRs (acute-chronic ratios) of each trophic level according to well-verified method, we derived provisional WQC (0.96 mg/L) of phenol for Korean seas for the first time. The procedure to derive marine WQC and results of this study could provide the essential information for the establishment of national marine WQC and WQBELs for HNS discharged from marine industrial facilities.

Field-portable seawater toxicity monitoring platform using lens-free shadow imaging technology.

The accidental spill of hazardous and noxious substances (HNSs) in the ocean has serious environmental and human health consequences. Assessing the ecotoxicity of seawater exposed to various HNS is challenging due to the constant development of new HNS or mixtures, and assessment methods are also limited. Microalgae viability tests are often used among the various biological indicators for ecotoxicity testing, as they are the primary producers in aquatic ecosystems. However, since the conventional cell growth rate test measures cell viability over three to four days using manual inspection under a conventional optical microscope, it is labor- and time-intensive and prone to subjective errors. In this study, we propose a rapid and automated method to evaluate seawater ecotoxicity by quantification of the morphological changes of microalgae exposed to more than 30 HNSs. This method was further validated using conventional growth rate test results. Dunaliella tertiolecta, a microalgae species without rigid cell walls, was selected as the test organism. Its morphological changes in response to HNS exposure were measured at the single cell level using a custom-developed device that uses lens-free shadow imaging technology. The ecotoxicity evaluation induced by the morphological change could be available in as little as 5 min using the proposed method and device, and it could be effective for 20 HNSs out of 30 HNSs tested. Moreover, the test results of six selected HNSs with high marine transport volume and toxicity revealed that the sensitivity of the proposed method extends to half the maximum effective concentration (EC50) and even to the lowest observed effective concentration (LOEC). Furthermore, the average correlation index between the growth inhibition test (three to four days) and the proposed morphology changes test (5 min) for the six selected HNSs was 0.84, indicating great promise in the field of various point-of-care water quality monitoring. Thus, the proposed equipment and technology may provide a viable alternative to traditional on-site toxicity testing, and the potential of rapid morphological analysis may replace traditional growth inhibition testing.

Spatial and temporal trends in polychlorinated naphthalenes in sediment from Ulsan and Onsan Bays of Korea: Potential sources and ecotoxicological concerns.

Few studies have been conducted on spatial and temporal trends in polychlorinated naphthalenes (PCNs) in coastal environments. Here, we describe 18 PCN congeners found in surface and dated sediment samples collected from highly industrialized bays of Korea. Measurable levels of PCN congeners were detected in all sediment samples, suggesting concurrent and historical contamination. The highest PCN concentrations were observed in sediment from rivers, streams, and the inner portions of the bays, which are surrounded by industrial complexes and commercial harbors. CNs 73, 66/67, and 52 were dominant in surface and dated sediment samples. Congener patterns and diagnostic ratios revealed that PCN contamination is originated from combustion processes and the use of polychlorinated biphenyl (PCB) technical mixtures. PCN concentrations in dated sediment increased from the 1980s to the mid-2000s and then decreased to 2015. Although the toxic equivalent (TEQ) levels of PCNs in our study did not exceed sediment quality guidelines proposed by international authorities, the cumulative risks from the TEQ concentrations of polychlorinated dibenzo-p-dioxins, furans, PCBs, and PCNs can be expected for benthic organisms.

Nationwide monitoring of cyclic and linear siloxanes in sediment and bivalves from Korean coastal waters: Occurrence, geographical distribution, and bioaccumulation potential.

Contamination of coastal environments by siloxanes is of growing concern. Sediment and bivalves were collected from 50 locations along the Korean coast to assess the geographical distribution, sources, and bioaccumulation potential of siloxanes. Cyclic and linear siloxanes were detectable in all sediment and bivalve samples. The highest siloxane concentrations were detected in sediment (656 ng/g dw) and bivalves (3273 ng/g dw) from highly industrialized bays and harbor-zones, suggesting that industrial and shipping activities are major sources of siloxanes in coastal environment. The geographical distribution of siloxanes was similar in sediment and bivalves. Sedimentary siloxanes were dominated by cyclic siloxanes, while linear siloxanes were predominant in bivalves. Bioaccumulation of linear siloxanes in bivalves originated mainly from the sedimentary environment. Mean biota-sediment accumulation factors (BSAFs) of seven siloxanes ranged from 1.26 to 6.03, indicating potential for bioaccumulation. This is the first report on the nationwide survey on siloxanes in Korean coastal waters.

A CMOS Image Sensor Based Refractometer without Spectrometry.

The refractive index (RI), an important optical property of a material, is measured by commercial refractometers in the food, agricultural, chemical, and manufacturing industries. Most of these refractometers must be equipped with a prism for light dispersion, which drastically limits the design and size of the refractometer. Recently, there have been several reports on the development of a surface plasmon resonance (SPR)-based RI detector, which is characterized by its high sensitivity and simplicity. However, regardless of the prism, an expensive spectrometer is required to analyze the resonance wavelength or angle of incidence. This paper proposes a method that eliminates the need for the prism and other conventional spectrometer components. For this purpose, total internal reflection SPR technology was used on an Ag thin film, and RI analysis was combined with a lens-free CMOS image sensor or a smartphone camera. A finite-difference time-domain (FDTD) numerical simulation was performed to evaluate the relationship between the output power intensity and Ag film thickness for different RIs at three wavelengths of commercial light-emitting diodes (LEDs). The maximum sensitivity of -824.54 RIU-1 was achieved with AG20 at an incident wavelength of 559 nm. Due to its simple design and cost effectiveness, this prism-less, SPR-based refractometer combined with a lens-free CMOS image sensor or a smartphone could be a superior candidate for a point-of-care device that can determine the RIs of various analytes in the field of biological or chemical sensing.

Investigation on the Printed CNT-Film-Based Electrochemical Sensor for Detection of Liquid Chemicals.

We studied electrochemical sensors using printed carbon nanotubes (CNT) film on a polyethylene telephtalate (PET) substrate. The mechanical stability of the printed CNT film (PCF) was confirmed by using bending and Scotch tape tests. In order to determine the optimum sensor structure, a resistance-type PCF sensor (R-type PCF sensor) and a comb-type PCF sensor (C-type PCF sensor) were fabricated and compared using a diluted NH3 droplet with various concentrations. The magnitude of response, response time, sensitivity, linearity, and limit of detection (LOD) were compared, and it was concluded that C-type PCF sensor has superior performance. In addition, the feasibility of PCF electrochemical sensor was investigated using 12 kinds of hazardous and noxious substances (HNS). The detection mechanism and selectivity of the PCF sensor are discussed.

Environmental and economic loss analyses of the oil discharge from shipwreck for salvage planning.

In this study, we carry out environmental and economic loss analyses of the oil discharge from the shipwreck Jeh Hun. By performing 500 simulations of hypothetical oil spill cases, we obtain the minimum and worst damage cases. In the minimum damage case, there is just marine pollution without coastal pollution or aquaculture farm pollution. On the other hand, in the worst damage case, there is serious marine pollution, coastal pollution, and aquaculture pollution. The main purpose of the environmental and economic loss analyses is to support salvage planning for the shipwreck, because we have to consider the oil discharge from the shipwreck during oil removal and salvage. The results of this study show that the best salvage time is early morning in winter, when the northwest wind and maximum flood tide are dominant resulting in the spilt oil going forward into the open sea without coastal pollution and aquaculture pollution.

Gas Sensor by Direct Growth and Functionalization of Metal Oxide/Metal Sulfide Core-Shell Nanowires on Flexible Substrates.

We have developed a novel fabrication method for flexible gas sensors for toxic gases based on sequential wet chemical reaction. In specific, zinc oxide (ZnO) nanowires were locally synthesized and directly integrated on a flexible polymer substrate using localized hydrothermal synthesis methods and their surfaces were selectively functionalized with palladium (Pd) nanoparticles using a liquid phase deposition process. Because the entire process is conducted at a low temperature in a mild precursor solution, it can be applied for flexible substrates. Furthermore, the surface of ZnO nanowires was sulfurized by hydrogen sulfide (H2S) gas to form zinc oxide/zinc sulfide (ZnO/ZnS) core-shell nanowires for stable sensing of H2S gas. The locally synthesized ZnO/ZnS core-shell nanowires enable an ultracompact-sized device, and Pd nanoparticles improve the sensing performance and reduce the operating temperature (200 °C). The device shows a high sensitivity [(Ggas - Gair)/Gair × 100% = 4491% to 10 ppm], fast response (response/recovery time <100 s) to hydrogen sulfide, and outstanding selectivity (>100 times) to other toxic gases (e.g., carbon monoxide, acetone, ethanol, and toluene). Moreover, vertically synthesized nanowires provide a long bending path, which reduces the mechanical stresses on the structure. The devices showed stable gas sensing performance under 9 mm positive radius of curvature and 5 mm negative radius of curvature. The mechanical robustness of the device was also verified by numerical simulations which showed dramatic decrease of maximum stress and strain to 4.2 and 5.0%, respectively.

Initial environmental risk assessment of hazardous and noxious substances (HNS) spill accidents to mitigate its damages.

In this study, a system was established to perform an initial environmental risk assessment of hazardous and noxious substances (HNS) spill accidents. Initial environmental risk assessment was performed using exposure and hazard assessments. An integrated hydrodynamic and chemical fate model was used to predict HNS concentrations at harbors, taking into account local environmental conditions. To consider the worst case HNS spill accident, the spill amount of 10,000 tonnages, was used for this study. The results show that highly soluble HNS are fatal to marine organisms during the neap tide. The results were based on a hypothetical worst case HNS spill accident and, not any specific actual HNS spill accident. Nevertheless, the method and system developed in this study, which includes the physical/chemical properties of 158 priority HNS, can be readily used to perform an initial environmental risk assessment for future HNS spill accidents.

A Field-Portable Cell Analyzer without a Microscope and Reagents.

This paper demonstrates a commercial-level field-portable lens-free cell analyzer called the NaviCell (No-stain and Automated Versatile Innovative cell analyzer) capable of automatically analyzing cell count and viability without employing an optical microscope and reagents. Based on the lens-free shadow imaging technique, the NaviCell (162 × 135 × 138 mm³ and 1.02 kg) has the advantage of providing analysis results with improved standard deviation between measurement results, owing to its large field of view. Importantly, the cell counting and viability testing can be analyzed without the use of any reagent, thereby simplifying the measurement procedure and reducing potential errors during sample preparation. In this study, the performance of the NaviCell for cell counting and viability testing was demonstrated using 13 and six cell lines, respectively. Based on the results of the hemocytometer (de facto standard), the error rate (ER) and coefficient of variation (CV) of the NaviCell are approximately 3.27 and 2.16 times better than the commercial cell counter, respectively. The cell viability testing of the NaviCell also showed an ER and CV performance improvement of 5.09 and 1.8 times, respectively, demonstrating sufficient potential in the field of cell analysis.

Pollution risk assessment of oil spill accidents in Garorim Bay of Korea.

This study presents a model to assess the oil spill risk in Garorim Bay in Korea, where large-scale oil spill accidents frequently occur. The oil spill risk assessment is carried out by using two factors: 1) The impact probability of the oil spill, and 2) the first impact time of the oil that has been spilt. The risk assessment is conducted for environmentally sensitive areas, such as the coastline and aquaculture farms in the Garorim Bay area. Finally, Garorim Bay is divided into six subareas, and the risks of each subarea are compared with one another to identify the subarea that is most vulnerable to an oil spill accident. These results represent an objective and comprehensive oil spill risk level for a specific region. The prediction of the oil spill spread is based on real-time sea conditions and can be improved by integrating our results, especially when sea conditions are rapidly changing.

Development of waterborne oil spill sensor based on printed ITO nanocrystals.

Oil spill accidents occasionally occur in coastal and ocean environments, and cause critical environmental damage, spoiling the marine habitats and ecosystems. To mitigate the damages, the species and amount of spilled oil should be monitored. In this study, we developed a waterborne oil spill sensor using a printed ITO layer. ITO is a compatible material for salty environments such as oceans because ITO is strong against corrosion. The fabricated sensor was tested using three oils, gasoline, lubricant and diesel, and different oil thicknesses of 0, 5, 10, and 15mm. The results showed that the resistance of the sensor clearly increased with the oil thickness and its electrical resistance. For sustainable sensing applications in marine environments, XRD patterns confirmed that the crystal structure of the ITO sensor did not change and FE-SEM images showed that the surface was clearly maintained after tests.

Risk assessment and national measure plan for oil and HNS spill accidents near Korea.

Many oil and HNS spill accidents occur in the waters surrounding the Korean Peninsula because Korea is one of the biggest trading partners in the world. In this study, we analyzed the oil and HNS spill accidents that occurred between 1994 and 2005 and created risk matrices to assess these accidents. The worst scenarios of future oil and HNS spill accidents were established, and the maximum spill amounts were estimated using historic accident data and a correlation from IPIECA. The maximum spill amounts are estimated to be between 77,000 and 10,000 tons of oil and HNS, respectively. One third of the spill materials should be removed using recovery equipment within three days of the spill event, according to the national measure plan. The capability of recovery equipment to remove spill materials can be estimated, and the equipment should then be prepared to mitigate the harmful effects of future oil and HNS accidents on humans and marine ecosystems.