Thermally Activated Defect Engineering for Highly Stable and Uniform ALD-Amorphous IGZO TFTs with High-Temperature Compatibility.

Highly stable IGZO thin-film transistors derived from atomic layer deposition are crucial for the semiconductor industry. However, unavoidable defect generation during high-temperature annealing results in abnormal positive bias temperature stress (PBTS). Herein, we propose a defect engineering method by controlling the gate insulator (GI) deposition temperature. Applying a GI deposition temperature of 400 °C to the In0.52Ga0.18Zn0.30O active layer effectively suppresses defects even after 600 °C annealing, preserving the amorphous phase of IGZO. The device exhibits a threshold voltage (VTH) of 0.05 V, a field-effect mobility of 27.6 cm2/Vs, a subthreshold swing of 61 mV/decade, and a hysteresis voltage of 0.01 V, demonstrating highly reliable PBTS and negative bias temperature stress. A power-law fit of the PBTS stability under 2 MV/cm of gate field stress and 120 °C of temperature stress predicts a VTH shift of -0.01 V after 10 years. Moreover, the proposed method ensures reliable uniformity over a large 4 in. area.

Sequential treatment from mandibulectomy to reconstruction on mandibular oral cancer - Case review I: mandibular ramus and angle lesion of primary intraosseous squamous cell carcinoma.

Primary intraosseous squamous cell carcinoma (PIOSCC) is very rare type of squamous cell carcinoma (SCC) that occurs within the jaw and arises from remnants of odontogenic epithelium with no connection to the oral mucosa. This study reports two cases of PIOSCC of the mandible. Reported in this article are two cases of PIOSCC of the mandible that were treated with resection and reconstruction using a fibular free flap. The first case was a 36-year-old male patient who complained of right mandibular pain. Computed tomography (CT) and panoramic radiograph revealed a large radiolucency in the mandibular ramus area. At first, an odontogenic keratocyst was tentatively diagnosed, and an excision procedure was carried out at another clinic. A final biopsy after cyst enucleation revealed well-differentiated SCC, so we proceeded with segmental mandibulectomy and reconstruction using a fibular free flap. The second case was a 48-year-old male patient with left mandibular pain. CT and panoramic radiograph revealed irregular radiolucency in the mandibular angle area near tooth #38. At first, osteomyelitis was tentatively diagnosed, and a curettage was carried out. A later biopsy revealed well-differentiated SCC, so segmental mandibulectomy and reconstruction with a fibular free flap were secondarily performed. Our two cases have had no recurrence. The facial appearance of both patients is satisfactory, and the neo-mandibular body created using a fibular bone transfer displays adequate bony volume.

Prognosis of teeth in mandibular fracture lines.

BACKGROUND/AIMS: Teeth in a jaw fracture line, because of the presence of the periodontal ligament, may communicate with the oral cavity. There are no guidelines for the management of teeth in mandibular fracture lines. The aim of this study was to investigate the factors related to dental problems with teeth involved in mandibular fracture lines and to determine the best treatment option. MATERIAL AND METHODS: This retrospective study was based on the medical and radiographic records of patients with mandibular fractures. The relationships among the patient's age, gender, smoking history, amount of bony displacement, surgery, trauma-surgery period, apical involvement, tooth mobility, and periodontal status were investigated. Group comparisons were performed using the chi-squared test, Fisher's exact test, and Mann-Whitney U-test. RESULT: A total of 238 patients (247 fracture lines) with mandibular fractures including a tooth in the line of the fracture were examined. Post-operative dental complications occurred in 42 cases (17.0%). Extraction of related teeth occurred in 34 cases (80.9%) compared to eight cases (19.0%) related to root canal therapy. This study defined "dental problem" as "a case with a tooth extracted or endodontically treated after trauma." The variables associated with an increased risk of dental problems were the amount of bony displacement (p < .01), tooth mobility (p < .01), and pre-existing marginal alveolar bone loss (p = .027). CONCLUSION: The prognosis of teeth in mandibular fracture lines was related to tooth mobility, periodontal state, and the amount of bony displacement.

Whitlockite Granules on Bone Regeneration in Defect of Rat Calvaria.

Whitlockite (WH; Ca18Mg2(HPO4)2(PO4)12) is a calcium phosphate based ceramic that contains magnesium ions. As the second most abundant mineral in living bone, WH occupies 25-35 wt % of the inorganic portion of human bone. Compared to hydroxyapatite (HAp, Ca10(PO4)6(OH)2), WH possesses better mechanical properties, faster resorbability, and promotion behavior on the osteogenesis. In this article, we introduced a fabrication method of interconnected porous WH granules through vacuum filtration, followed by sintering treatment based on the thermal stability of WH synthesized using the tri-solvent system. This study presents a histological, radiological, and immunohistochemical evaluation of the bone healing potential of these WH granules in a 5 mm diameter calvarial bone defect in rats. The histological evaluation shows no inflammation or foreign body reaction in the WH group. The WH group displays newly formed bone at the same thickness as the original bone. On the contrary, bone formation is not observed in the nontreated (NT) group. Besides, immunohistochemistry (IHC) confirmed that WH granules promoted bone regeneration with the significantly higher expression of bone morphogenetic proteins-2 (BMP-2), alkaline phosphatase (ALP), osteopontin (OPN), and osteocalcin (OCN) compared to the NT group without the addition of exogenous cells or growth factors. These results suggest that WH has excellent potential for application in bone tissue regeneration.

Mandibular reconstruction with a ready-made type and a custom-made type titanium mesh after mandibular resection in patients with oral cancer.

BACKGROUND: After the resection at the mandibular site involving oral cancer, free vascularized fibular graft, a type of vascularized autograft, is often used for the mandibular reconstruction. Titanium mesh (T-mesh) and particulate cancellous bone and marrow (PCBM), however, a type of non-vascularized autograft, can also be used for the reconstruction. With the T-mesh applied even in the chin and angle areas, an aesthetic contour with adequate strength and stable fixation can be achieved, and the pores of the mesh will allow the rapid revascularization of the bone graft site. Especially, this technique does not require microvascular training; as such, the surgery time can be shortened. This advantage allows older patients to undergo the reconstructive surgery. CASE PRESENTATION: Reported in this article are two cases of mandibular reconstruction using the ready-made type and custom-made type T-mesh, respectively, after mandibular resection. We had operated double blind peer-review process. A 79-year-old female patient visited the authors' clinic with gingival swelling and pain on the left mandibular region. After wide excision and segmental mandibulectomy, a pectoralis major myocutaneous flap was used to cover the intraoral defect. Fourteen months postoperatively, reconstruction using a ready-made type T-mesh (Striker-Leibinger, Freibrug, Germany) and iliac PCBM was done to repair the mandible left body defect.Another 62-year-old female patient visited the authors' clinic with pain on the right mandibular region. After wide excision and segmental mandibulectomy on the mandibular squamous cell carcinoma (SCC), reconstruction was done with a reconstruction plate and a right fibula free flap. Sixteen months postoperatively, reconstruction using a custom-made type T-mesh and iliac PCBM was done to repair the mandibular defect after the failure of the fibula free flap. The CAD-CAM T-mesh was made prior to the operation. CONCLUSIONS: In both cases, sufficient new-bone formation was observed in terms of volume and strength. In the CAD-CAM custom-made type T-mesh case, especially, it was much easier to fix screws onto the adjacent mandible, and after the removal of the mesh, the appearance of both patients improved, and the neo-mandibular body showed adequate bony volume for implant or prosthetic restoration.