Grit particle characterization: influence of sample pretreatment and sieving method.

Grit causes problems in water resource recovery facilities (WRRFs): clogging pipes, damaging pumps, and reducing the active volume of aeration tanks and anaerobic digesters by grit accumulation. Grit chambers are built to remove these particles. However, no standardized methodology exists to characterize grit particles for grit chamber design and operation despite the large observed variability in grit composition. Therefore, this paper proposes a combination and adaptation of existing methods to sample and characterize grit particles in view of proper grit chamber design and its modelling to ultimately optimize the efficiency of this important WRRF unit process. Characteristics evaluated included particle size distribution from sieving after different sample pretreatments, organic/inorganic fractions, and density.

Simultaneous organic matter removal and nitrification of an inert self-supporting immersed media to upgrade aerated lagoons.

A pilot study was performed to evaluate the potential of an inert self-supported immersed fixed film media to upgrade aerated lagoons. Simultaneous organic matter removal and nitrification was assessed under different loading rates and temperatures (near 0 °C) using 12 laboratory-scale reactors operated in parallel. Test results showed that both the temperature and the load have an influence on organic matter effluent concentrations. Effluent quality seemed related to the observed biofilm thickness. Thicker biofilm is believed to have contributed to biomass detachment and increased particulate organic matter concentrations in the effluent. Simultaneous organic removal and nitrification was obtained at loads above 5 g CBOD5/m2·d. The highest nitrification rate at 0.4 °C was obtained for the smallest load, which showed a nitrification limitation close to freezing point.

Long chain fatty acids (LCFA) evolution for inhibition forecasting during anaerobic treatment of lipid-rich wastes: Case of milk-fed veal slaughterhouse waste.

A detailed study of a solid slaughterhouse waste (SHW) anaerobic treatment is presented. The waste used in this study is rich in lipids and proteins residue. Long chain fatty acids (LCFA), coming from the hydrolysis of lipids were inhibitory to anaerobic processes at different degrees. Acetogenesis and methanogenesis processes were mainly affected by inhibition whereas disintegration and hydrolysis processes did not seem to be affected by high LCFA concentrations. Nevertheless, because of the high energy content, this kind of waste is very suitable for anaerobic digestion but strict control of operating conditions is required to prevent inhibition. For that, two inhibition indicators were identified in this study. Those two indicators, LCFA dynamics and LCFA/VSbiomass ratio proved to be useful to predict and to estimate the process inhibition degree.

Comparison of existing models to simulate anaerobic digestion of lipid-rich waste.

Models for anaerobic digestion of lipid-rich waste taking inhibition into account were reviewed and, if necessary, adjusted to the ADM1 model framework in order to compare them. Experimental data from anaerobic digestion of slaughterhouse waste at an organic loading rate (OLR) ranging from 0.3 to 1.9kgVSm-3d-1 were used to compare and evaluate models. Experimental data obtained at low OLRs were accurately modeled whatever the model thereby validating the stoichiometric parameters used and influent fractionation. However, at higher OLRs, although inhibition parameters were optimized to reduce differences between experimental and simulated data, no model was able to accurately simulate accumulation of substrates and intermediates, mainly due to the wrong simulation of pH. A simulation using pH based on experimental data showed that acetogenesis and methanogenesis were the most sensitive steps to LCFA inhibition and enabled identification of the inhibition parameters of both steps.

Understanding the contribution of biofilm in an integrated fixed-film-activated sludge system (IFAS) designed for nitrogen removal.

The objective of this study is to improve knowledge on the integrated fixed-film-activated sludge (IFAS) system designed for nitrogen removal. Biofilm growth and its contribution to nitrification were monitored under various operating conditions in a semi-industrial pilot-scale plant. Nitrification rates were observed in biofilms developed on free-floating media and in activated sludge operated under a low sludge retention time (4 days) and at an ammonia loading rate of 45-70 gNH4-N/kgMLVSS/d. Operational conditions, i.e. oxygen concentration, redox potential, suspended solids concentration, ammonium and nitrates, were monitored continuously in the reactors. High removal efficiencies were observed for carbon and ammonium at high-loading rate. The contribution of biofilm to nitrification was determined as 40-70% of total NOx-N production under the operating conditions tested. Optimal conditions to optimize process compacity were determined. The tested configuration responds especially well to winter and summer nitrification conditions. These results help provide a deeper understanding of how autotrophic biomass evolves through environmental and operational conditions in IFAS systems.

A calibration protocol of a one-dimensional moving bed bioreactor (MBBR) dynamic model for nitrogen removal.

This work suggests a procedure to correctly calibrate the parameters of a one-dimensional MBBR dynamic model in nitrification treatment. The study deals with the MBBR configuration with two reactors in series, one for carbon treatment and the other for nitrogen treatment. Because of the influence of the first reactor on the second one, the approach needs a specific calibration strategy. Firstly, a comparison between measured values and simulated ones obtained with default parameters has been carried out. Simulated values of filtered COD, NH(4)-N and dissolved oxygen are underestimated and nitrates are overestimated compared with observed data. Thus, nitrifying rate and oxygen transfer into the biofilm are overvalued. Secondly, a sensitivity analysis was carried out for parameters and for COD fractionation. It revealed three classes of sensitive parameters: physical, diffusional and kinetic. Then a calibration protocol of the MBBR dynamic model was proposed. It was successfully tested on data recorded at a pilot-scale plant and a calibrated set of values was obtained for four parameters: the maximum biofilm thickness, the detachment rate, the maximum autotrophic growth rate and the oxygen transfer rate.

A phenomenological retention tank model using settling velocity distributions.

Many authors have observed the influence of the settling velocity distribution on the sedimentation process in retention tanks. However, the pollutants' behaviour in such tanks is not well characterized, especially with respect to their settling velocity distribution. This paper presents a phenomenological modelling study dealing with the way by which the settling velocity distribution of particles in combined sewage changes between entering and leaving an off-line retention tank. The work starts from a previously published model (Lessard and Beck, 1991) which is first implemented in a wastewater management modelling software, to be then tested with full-scale field data for the first time. Next, its performance is improved by integrating the particle settling velocity distribution and adding a description of the resuspension due to pumping for emptying the tank. Finally, the potential of the improved model is demonstrated by comparing the results for one more rain event.

Characterization of the potential impact of retention tank emptying on wastewater primary treatment: a new element for CSO management.

Theoretical studies have shown that discharges from retention tanks could have a negative impact on the WWTP's (Wastewater Treatment Plant) effluent. Characterization of such discharges is necessary to better understand these impacts. This study aims at: (1) characterizing water quality during emptying of a tank; and (2) characterizing the temporal variation of settling velocities of the waters released to the WWTP. Two full-scale sampling campaigns (18 rain events) have been realized in Quebec City and laboratory analyses have shown a wide variability of total suspended solids (TSS) and Chemical Oxygen Demand (COD) concentrations in the water released from the tank. Suspended solids seem to settle quickly because they are only found in large amounts during the first 15 min of pumping to the WWTP. These solids are hypothesized to come from the pumping in which solids remained after a previous event. When these solids are evacuated, low TSS containing waters are pumped from the retention tank. A second concentration peak occurs at the end of the emptying period when the tank is cleaned with wash water. Finally, settling velocity studies allowed characterizing combined sewer wastewaters by separating three main fractions of pollutants which correspond to the beginning, middle and end of emptying. In most cases, it is noticed that particle settling velocities increase as the pollutant load increases.

Modeling of activated sludge transient behavior induced by regulation of carbon and nitrogen metabolism.

An experimental protocol to evaluate the structured biomass model proposed by Lavallée (Lavallée, Lessard, and Vanrolleghem, J Environ Eng Sci 2005;4:517-532) is presented. The protocol was devised to induce transient behavior and characterize the evolution of several internal biomass components. The proposed model is based on biochemical principles, and was fitted to the collected data. In these experiments, it was observed that filling the storage capacity of cells leads to special transient behavior, including a temporarily reduced metabolic activity. The model-based interpretation of the results showed that the observed transient behavior can be explained by cross-regulation of carbon and nitrogen metabolism. Hence, according to an extensive literature review, the cross-regulation of carbon and nitrogen can be used to model some observed transient behaviors and regulation of the storage process in activated sludge.

Understanding the HIV-1 protease reactivity with DFT: what do we gain from recent functionals?

The modeling of HIV-1 plays a crucial role in the understanding of its reactivity and its interactions with specific drugs. In this work, we propose a medium sized model to test the ability of a variety of quantum chemistry approaches to provide reasonable geometric parameters and energetics for this system. Although our model is large enough to include the main polarizing groups of the active site, it is small enough to be used within full quantum studies up to the second order Møller-Plesset (MP2) level with extrapolations to coupled cluster CCSD(T) level. These high level calculations are used as reference to assess the ability of electronic structure methods (semiempirical and DFT) to provide accurate geometries and energies for the HIV-1 protease reaction. All semiempirical methods fail to describe the geometry of the protease active site. Within DFT, pure generalized gradient approximation (GGA) functionals have difficulty in reproducing the reaction energy and underestimate the barrier. Hybrid and/or meta GGA approaches do not yield a consistent improvement. The best results are obtained with hybrid GGA B3LYP or X3LYP and with hybrid meta GGA functionals with a fraction of exact exchange around 30-40%, such as M06, B1B95, or BMK functionals. On the basis of these results, we propose an accurate and computationally efficient strategy, employing quantum chemistry methods. This is applied here to study the protonation state of the reaction intermediate and could be easily used in further QM/MM studies.

Modelling using rRNA-structured biomass models.

Models currently used have been developed to describe the storage response in the activated sludge process. In these models the distribution of the substrate flux between growth and storage is an empirical function. rRNA-structured biomass models are proposed to describe the metabolic status of cells in view of predicting the growth response (dmicro/dt) of cells in activated sludge process. The autocatalytic reaction rate of the synthesis of the PSS component (rRNA) can provide a mechanistic explanation for the growth response and the growth lag phase. The proposed models were able to describe and predict properly the growth response of the biomass in various types of reactor. Such models could be more widely applicable by using intrinsic model parameters. This would be a key improvement for as it would lead to improved models for design.

Aeration effect on the efficiency of swine manure treatment in a trickling filter packed with organic materials.

Effect of aeration rate on the removal of organic matter and nitrogen and on the formation of NH3, N2O and N2 was studied for an extensive biofiltration system packed with an organic media, which was used to treat pig manure. The results show high removal of BOD5 and TSS (99 and > or = 98%), independently of the four aeration rate tested (3.4-34 m3/m2 x h). Aeration rate > or = 4.4 m/h resulted in high ammonia stripping during start-up (> or = 1.0 kg NH3-N/m3 of swine manure treated), while using 3.4 m/h only 0.3 kg NH3-N/m3 were stripped. Complete nitrification was achieved after day 100 of operation, except in the biofilter with the lowest aeration rate. Simultaneous denitrification established in all the biofilters. Applying an aeration rate of 9.4 m/h up to 1.2 kg nitrogen was removed in the form of N2 for each m3 of swine manure treated. Contrary to the expectations, N2 formation and release increased with the aeration rate. This particular behaviour seems to be related to the punctual accumulation of water layers inside the biofilters, caused by the air force flowing in the opposite direction to the water flux. N2O production was quite similar in all biofilters (between 0.25-0.36 kg N2O-N/m3 of swine manure treated).

Toward an operational dynamic model for tertiary nitrification by submerged biofiltration.

This work deals with the methodology put in place to fit and validate the parameters of a biofiltration model (BAF) in tertiary nitrification treatment and dynamic conditions. For an average loading rate of 0.65 kg NH4-N/m(3) media/d, different time loading rates are applied inside a filtration-backwash run using a semi-industrial pilot. Comparisons between predicted and observed values on the NH4-N, NO3-N and TSS in treated water and the total head loss deltaP are carried out firstly using default values of BAF parameters. Model predictions overestimate values measured but trends are well reproduced. A sensitivity analysis is carried out and the hierarchy of BAF parameters has been set up classifying them into strong and low influence on the effluent concentrations. Among parameters revealing the strongest influence are those of the filtration module and the mean density of biofilm for the TSS effluent and the total AP, the specific autotrophic growth rate, the maximum biofilm thickness and the reduction coefficient of diffusivity in the biofilm for the NH4-N, NO3-N effluent. Finally, this classification leads to setting a calibration procedure, thanks to specific experimental tests directly measuring some BAF parameters.

Effect of algal incorporation on growth, survival and carcass composition of rainbow trout (Oncorhynchus mykiss) fry.

A nutritional assay has been conducted with rainbow trout fry (Oncorhynchus mykiss) using a biomass of photosynthetic micro-organisms. The algal biomass was incorporated in the feed at increasing levels (12.5%, 25% and 50%) in order to verify the effects on survival (%), growth (length and mass) and carcass quality of the fish (skin color, water, protein and lipid content). Two commercial feeds (CF, as sold, and 0% A, reprocessed without algae) have been used as controls. After eight weeks at 10 degrees C, the growth has been significantly reduced in fish fed the feeds containing 25% and 50% algae diets (P<0.01). Moreover, an incorporation of algae higher than 12.5% in the feed led to a increase of water content (CF versus other diets; P<0.01) and TL (CF versus 50% A; P<0.01) (wet basis) content of carcasses. Survival was 100% in all treatment groups. Under the experimental conditions used, the results obtained show that a maximum of 12.5% of algal biomass can be incorporated in the feed for rainbow trout fry (O. mykiss) without negative consequences on growth and body content in lipids and energy of fish.

Dynamical studies of the ozone isotope effect: A status report.

Dynamical studies of the recombination of O and O2 to form ozone are reviewed. The focus is the intriguing isotope dependence of the recombination rate coefficient as observed by Mauersberger and coworkers in the last decade. The key quantity for understanding of this dependence appears to be the difference of zero-point energies of the two fragmentation channels to which excited ozone can dissociate, i.e., X + YZ <-- XYZ* --> XY + Z, where X, Y, and Z stand for the three isotopes of oxygen. Besides the isotope dependence, the variation of the recombination rate coefficient with pressure and temperature is also addressed. Despite the numerous approaches of recent years, the recombination of ozone is far from being satisfactorily explained; there are still several essential questions to be solved by detailed theoretical analysis. We mainly discuss--and critically assess--the results of our own investigations of the ozone kinetics. The work of other research groups is also evaluated.

Characterization of Streptomyces MITKK-103, a newly isolated actinomycin X2-producer.

A new actinomycete strain designated MITKK-103 was isolated from the soil of a flowerpot using a humic acid agar medium. The newly isolated strain was able to produce a large amount of actinomycin X2 even under nonoptimized growing conditions and serves as a promising source of this antibiotic. Actinomycin X2 has higher cytotoxicity toward cultured human leukemia (HL-60) cells than does actinomycin D, and it induces cell death via apoptosis. A nearly complete 16S ribosomal DNA (rDNA) sequence from the isolate was determined and found to have high identity (98.5-100%) with Streptomyces galbus, Streptomyces griseofuscus, and Streptomyces padanus, indicating that MITKK-103 belongs to the genus Streptomyces. The isolate clustered with species belonging to the S. padanus clade in a 16S-rDNA-based phylogenetic tree and showed 75% overall homology to S. padanus ATCC 25646 in DNA-DNA relatedness analysis. Although the growth of the isolate was somewhat different from the three species mentioned, the strain MITKK-103 most closely resembles S. padanus on the basis of the morphological and phenotypic characteristics, phylogenetic analysis, and genotypic data. As such, this is the first report of a strain of S. padanus capable of producing actinomycins.

Nitrogen elimination mechanisms in an organic media aerated biofilter treating pig manure.

Biofilters using organic media are known to procure efficient treatment for different types of wastewater, but the nitrogen removal pathways implied are still not well understood. In this study, a lab-scale aerated biofilter using peat and treating pig manure was operated for 180 days, in order to quantify the nitrogen transformations occurring in it. It was shown that stripping was important during the start-up, until nitrification took place. Simultaneous nitrification and denitrification, proved by N2 production, became the principal mechanism after some time. The production of N2O did not seem to come only from heterotrophic denitrification, but also from chemodenitrification and autotrophic denitrification. It has also been found that part of the influent nitrogen was retained in the system during the first 150 days, due to filtration, sorption and assimilation. During the last periods of operation, the nitrogen previously retained has been used by microorganisms, leading to an excessive N2 discharge.

Determination of the hydraulic residence time in a trickling biofilter filled with organic matter.

Biofiltration process using peat as media has been shown to be efficient for the treatment of agroindustrial, chemical and municipal effluents. However, determining the hydraulic retention time of this process is difficult due to many factors. Generally tracer techniques are used, but they measure the molecular retention time instead of the hydraulic retention time; and depending on the case, the results can be wrong. In order to contribute to solving this problem, the objective of this research was to find a trustworthy and adequate technique to determine the hydraulic retention time for a process using a very adsorbent filter bed material (peat). An overview of the hydraulic behaviour of a peat bed filter related to their particular structural composition is presented. Then, based on these characteristics, two different techniques to determine the hydraulic retention time were developed and tested. The first, an indirect modified tracing technique and, the second, a direct one which determines the volume of liquid in treatment into the filter bed through the establishment of a relation between the volume of porosity and the volume of empty spaces (or not occupied by liquid) into the filter bed. The results obtained showed that the proposed techniques gave similar results and proved adequate.

Disparity between changes in mRNA abundance and enzyme activity in Corynebacterium glutamicum: implications for DNA microarray analysis.

The relationship between changes in mRNA abundance and enzyme activity was determined for three genes over a span of nearly 3 h during amino acid production in Corynebacterium glutamicum. Gene expression changes during C. glutamicum fermentations were examined by complementary DNA (cDNA) microarrays and by a second method for quantitating RNA levels, competitive reverse transcriptase-PCR (RT-PCR). The results obtained independently by both methods were compared and found to be in agreement, thus validating the quantitative potential of DNA microarrays for gene expression profiling. Evidence of a disparity between mRNA abundance and enzyme activity is presented and supports our belief that it is difficult to generally predict protein activity from quantitative transcriptome data. Homoserine dehydrogenase, threonine dehydratase, and homoserine kinase are enzymes involved in the biosynthesis of l-isoleucine and other aspartate-derived amino acids in C. glutamicum. Our data suggest that different underlying regulatory mechanisms may be connected with the expression of the genes encoding each of these three enzymes. Indeed, whereas in one case the increases in enzyme activity exceeded those in the corresponding mRNA abundance, in another case large increases in the levels of gene expression were not congruent with changes in enzyme activity.

Structural changes induced by NaCl in companion and transfer cells of Medicago sativa blades.

Medicago sativa var. Gabes is a perennial glycophyte that develops new shoots even in high salinity (150 mM NaCl). In the upper exporting leaves, K(+) is high and Na(+) is low by comparison with the lower leaves, where Na(+) accumulation induces chlorosis after 4 weeks of NaCl treatment. By secondary ion mass spectroscopy, a low Na(+)/K(+) ratio was detected in the phloem complex of blade veins in these lower leaves. By transmission electron microscopy, the ultrastructural features were observed in the phloem complex. In the upper leaves of both control and NaCl-treated plants, companion cells in minor veins were found to be transfer cells. These cells may well be involved in the intravenous recycling of ions and in Na(+) flowing out of exporting leaves. Under the effect of NaCl, companion cells in the main veins develop transfer cell features, which may favor the rate of assimilate transport from exporting leaves toward meristems, allowing the positive balance necessary for the survival in salt conditions. These features no longer assist the lower leaves when transfer cells are necrotized in both minor and main veins of NaCl-treated plants. As transfer cells are the only degenerating phloem constituent, our observations emphasize their role in controlling nutrient (in particular, Na(+)) fluxes associated with the stress response.