Dual-Energy-Barrier Stable Superhydrophobic Structures for Long Icing Delay.

Using superhydrophobic surfaces (SHSs) with the water-repellent Cassie-Baxter (CB) state is widely acknowledged as an effective approach for anti-icing performances. Nonetheless, the CB state is susceptible to diverse physical phenomena (e.g., vapor condensation, gas contraction, etc.) at low temperatures, resulting in the transition to the sticky Wenzel state and the loss of anti-icing capabilities. SHSs with various micronanostructures have been empirically examined for enhancing the CB stability; however, the energy barrier transits from the metastable CB state to the stable Wenzel state and thus the CB stability enhancement is currently not enough to guarantee a well and appliable anti-icing performance at low temperatures. Here, we proposed a dual-energy-barrier design strategy on superhydrophobic micronanostructures. Rather than the typical single energy barrier of the conventional CB-to-Wenzel transition, we introduced two CB states (i.e., CB I and CB II), where the state transition needed to go through CB I and CB II then to Wenzel state, thus significantly improving the entire CB stability. We applied ultrafast laser to fabricate this dual-energy-barrier micronanostructures, established a theoretical framework, and performed a series of experiments. The anti-icing performances were exhibited with long delay icing times (over 27,000 s) and low ice-adhesion strengths (0.9 kPa). The kinetic mechanism underpinning the enhanced CB anti-icing stability was elucidated and attributed to the preferential liquid pinning in the shallow closed structures, enabling the higher CB-Wenzel transition energy barrier to sustain the CB state. Comprehensive durability tests further corroborated the potentials of the designed dual-energy-barrier structures for anti-icing applications.

Self-Driven Droplet Motions Below their Icing Points.

Liquid fluidity is a most key prerequisite for a broad range of technologies, from energy, fluid machineries, microfluidic devices, water, and oil transportation to bio-deliveries. While from thermodynamics, the liquid fluidity gradually diminishes as temperature decreases until completely solidified below icing points. Here, self-driven droplet motions are discovered and demonstrated occurring in icing environments and accelerating with both moving distances and droplet volumes. The self-driven motions, including self-depinning and continuous wriggling, require no surface pre-preparation or energy input but are triggered by the overpressure spontaneously established during icing and then continuously accelerated by capillary pulling of frosts. Such self-driven motions are generic to a broad class of liquid types, volumes, and numbers on various micro-nanostructured surfaces and can be facilely manipulated by introducing pressure gradients spontaneously or externally. The discovery and control of self-driven motions below icing points can greatly broaden liquid-related applications in icing environments.

Boosting water evaporation via continuous formation of a 3D thin film through triple-level super-wicking routes.

Capillary-fed thin-film evaporation via micro/nanoscale structures has attracted increasing attention for its high evaporation flux and pumpless liquid replenishment. However, maximizing thin-film evaporation has been hindered by the intrinsic trade-off between the heat flux and liquid transport. Here, we designed and fabricated nanostructured micro-steam volcanoes on copper surfaces featuring triple-level super-wicking routes to overcome this trade-off and boost water evaporation. The triple-level super-wicking routes enable the continuous formation of a 3D thin film for highly efficient evaporation by continuous self-driven liquid replenishment and extending the thin-film region. The micro-steam volcanoes increased the surface area by 225%, improving the evaporation rate by 141%, with a rapid self-pumping water transport speed up to 80 mm s-1. A remarkable solar-driven water evaporation rate of 3.33 kg m-2 h-1 under one sun vertical incidence was achieved, which is among the highest reported values for metal-based evaporators. When attached to electric-heating plates, the evaporator realized an electrothermal evaporation rate of 12.13 kg m-2 h-1. Moreover, it can also be used for evaporative cooling with enhanced convective heat transfer, reaching a 36.2 °C temperature reduction on a heat source with a heat flux of 6 W cm-2. This study promises a general strategy for designing thin-film evaporators with high efficiencies, low costs, and multi-functional compatibilities.