Your browser doesn't support javascript.
loading
Mostrar: 20 | 50 | 100
Resultados 1 - 13 de 13
Filtrar
Mais filtros










Base de dados
Intervalo de ano de publicação
1.
Adv Sci (Weinh) ; 10(26): e2302917, 2023 Sep.
Artigo em Inglês | MEDLINE | ID: mdl-37401139

RESUMO

The charge transport in quasi-2D perovskites limits their applications despite the superior stability and optoelectronic properties. Herein, a novel strategy is proposed to enhance the charge transport by regulating 3D perovskite phase in quasi-2D perovskite films. The carbohydrazide (CBH) as an additive is introduced into (PEA)2 MA3 Pb4 I13 precursors, which slows down the crystallization process and improves the phase ratio and crystal quality of the 3D phase. This structure change results in a significant improvement in charge transport and extraction, leading to the device demonstrating an almost 100% internal quantum efficiency, a peak responsivity of 0.41 A W-1 , and a detectivity of 1.31 × 1012 Jones at 570 nm under 0 V bias. Furthermore, the air and moisture stability of (PEA)2 MA3 Pb4 I13 films is not deteriorated but gets significantly improved due to the better crystal quality and the passivation of defects by the residual CBH molecule. This work demonstrates a strategy for improving the charge transport properties of quasi-2D perovskites and also sheds light on solving the stability issue of 3D perovskite films via the proper passivation or additives, which will inspire the fast development of the perovskite community.

2.
ACS Omega ; 8(23): 20912-20919, 2023 Jun 13.
Artigo em Inglês | MEDLINE | ID: mdl-37332778

RESUMO

The low electrical conductivity and the high surface defect density of the TiO2 electron transport layer (ETL) limit the quality of the following perovskite (PVK) layers and the power conversion efficiency (PCE) of corresponding perovskite solar cells (PSCs). Sulfur was reported as an effective element to passivate the TiO2 layer and improve the PCE of PSCs. In this work, we further investigate the effect of chemical valences of sulfur on the performance of TiO2/PVK interfaces, CsFAMA PVK layers, and solar cells using TiO2 ETL layers treated with Na2S, Na2S2O3, and Na2SO4, respectively. Experimental results show that the Na2S and Na2S2O3 interfacial layers can enlarge the grain size of PVK layers, reduce the defect density at the TiO2/PVK interface, and improve the device efficiency and stability. Meanwhile, the Na2SO4 interfacial layer leads to a smaller perovskite grain size and a slightly degraded TiO2/PVK interface and device performance. These results indicate that S2- can obviously improve the quality of TiO2 and PVK layers and TiO2/PVK interfaces, while SO42- has little effects, even negative effects, on PSCs. This work can deepen the understanding of the interaction between sulfur and the PVK layer and may inspire further progress in the surface passivation field.

3.
ACS Omega ; 6(50): 34485-34493, 2021 Dec 21.
Artigo em Inglês | MEDLINE | ID: mdl-34963933

RESUMO

Interfacial defects at the electron transport layer (ETL) and perovskite (PVK) interface are critical to the power conversion efficiency (PCE) and stabilities of the perovskite solar cells (PSCs) via significantly affecting the quality of both interface contacts and PVK layers. Here, we demonstrate a simple ionic bond passivation method, employing Na2S solution treatment of the surface of titanium dioxide (TiO2) layers, to effectively passivate the traps at the TiO2/Cs0.05(MA0.15FA0.85)0.95Pb(Br0.15I0.85)3 PVK interface and enhance the performance of PSCs. X-ray photoelectron spectroscopy and other characterizations show that the Na2S treatment introduced S2- ions at the TiO2/PVK interface, where S2- ions effectively bridged the TiO2 ETL and the PVK layer via forming chemical bonds with Ti atoms and with uncoordinated Pb atoms and resulted in the reduced defect density and improved the crystallinity of PVK layers. In addition, the S2- ions can effectively enlarge the grain size of the PVK layers. The average PCE of solar cells is improved from 15.77 to 19.06% via employing the Na2S-treated TiO2 layers. This work demonstrates a simple and facile interface passivation method using ionic bond passivation to afford high-performance PSCs. The bridging effect of S2- ions may inspire the further exploration of the ionic bond passivation and sulfur-based passivation materials.

4.
Nanoscale ; 13(47): 19894-19902, 2021 Dec 13.
Artigo em Inglês | MEDLINE | ID: mdl-34761770

RESUMO

Progress towards high performance X-ray detection and dynamic imaging applications, including nondestructive inspection, homeland security, and medical diagnostics, requires scintillators with a high light yield, a reasonable decay time, low cost, and eco-friendliness. Recently, copper halide scintillators have drawn tremendous attention due to their outstanding radioluminescence performance. Here, we first employed ß-Cs3Cu2Cl5 as a high-performance scintillator, with a photoluminescence quantum yield (PLQY) of 94.6%, a radioluminescence light yield of 34 000 ± 4000 photons per MeV, a low detection limit of 81.7 nGyair s-1, and good operational stability under a total X-ray dose of 174.6 Gyair in air. In addition, this scintillator presents a high spatial resolution of 9.6 lp mm-1 at the modulation transfer function of 0.2 and a superb performance at 60 frames per second in our X-ray imaging system. Overall, this highly efficient scintillator demonstrates outstanding comprehensive performance and shows great potential for broad applications in X-ray detection and dynamic imaging.

5.
Opt Express ; 29(14): 22578-22592, 2021 Jul 05.
Artigo em Inglês | MEDLINE | ID: mdl-34266017

RESUMO

Radiation detection technologies have been applied in broad fields such as security inspection, medical diagnosis, environment monitoring and scientific analysis. Fiber-optic radiation detectors exhibit unique advantages including miniaturization, resistance to water, remote monitoring, and distributable detection. However, the low sensitivity and the high limit-of-detection limit its practical applications. Herein we demonstrated high-performance fiber-optic X-ray detectors with scintillating composites consisting of UV glue and uniformly distributed gadolinium oxysulfide (GADOX) powders. The impacts of the length, thickness and GADOX weight ratio of the composite coating upon the detector performance, were systematically investigated in terms of the generation and the coupling efficiency of radio-luminescence. Besides the high-performance scintillator, the scattering loss and the geometric factor greatly affected the detector performance. A higher sensitivity and lower limit-of-detection could be achieved by increasing the GADOX weight ratio and decreasing the thickness simultaneously. The optimal detector with the highest GADOX weight ratio (70%), exhibited a linear sensitivity to the X-ray dose rate within 31-1575 µGyair/s, and a low limit-of-detection of ∼0.26 µGyair/s at a tube voltage of 120 kV. The mechanism discussed here will provide insightful guidance for further development of fiber-optic radiation detectors and these promising results demonstrate the potential applications of fiber-optic detectors.

6.
ACS Omega ; 5(36): 23111-23117, 2020 Sep 15.
Artigo em Inglês | MEDLINE | ID: mdl-32954161

RESUMO

Fabricating perovskite single-crystal thin films (SCTFs) in controllable manner is the major challenge for the promising potential applications in optoelectronic devices. Although modifying the substrate surface is frequently used to realize the controlled growth of perovskite SCTFs, it is still unclear how the substrate condition affects the crystallization process. In this work, we systemically investigated the effects of the surface hydrophobicity of indium tin oxide substrates on the crystallization process of MAPbBr3 SCTFs prepared by the space-confined method. Comprehensive characterizations show that the surface morphology and crystallinity of SCTFs are improved, and the defect density is reduced when increasing the substrate hydrophobicity. The best MAPbBr3 thin film obtained has a full width at half-height of the rocking curve of the (001) crystal plane of 0.044°. The mechanism of the substrate hydrophobicity on the crystal growth is also discussed. These results will provide guidance to the controllable growth of high-quality SCTFs for perovskite SCTF devices.

7.
ACS Appl Mater Interfaces ; 11(36): 32969-32977, 2019 Sep 11.
Artigo em Inglês | MEDLINE | ID: mdl-31426629

RESUMO

Betavoltaic devices are very appealing to applications in out-space exploration, deep-sea facilities, and implantable medical devices for their ultralong lifetime and high power density. The key to further improve the betavoltaic device efficiency is to find proper semiconductor materials with long carrier diffusion lengths and having strong interactions with ß-particles. Halide perovskite would be a promising candidate material for betavoltaics due to the long carrier diffusion length, the high defect tolerance, the strong interaction with ß-particles, and the wide adjustable band gap. Until now, little research has been done on perovskite-betavoltaic devices. In this work, we demonstrated a prototype perovskite-betavoltaic cell with a power conversion efficiency of 3.56% and a maximum output power of 534 nW, under electron radiation equivalent to a 10 keV and 253 mCi source mimicked by an electron gun. The device efficiency can be further improved via the device structure optimization and advanced device fabrication technique. Excellent power conversion efficiencies of 21.0 and 19.6% can be achieved for the 63Ni and 3H perovskite-betavoltaic devices based on results of the Geant4 simulation, respectively. These results indicate the brilliant prospects of perovskite materials in betavoltaic power sources.

8.
Nanoscale ; 10(8): 3893-3903, 2018 Feb 22.
Artigo em Inglês | MEDLINE | ID: mdl-29419846

RESUMO

Interface engineering is an important method to modulate electronic structures for improving the physical properties of semiconductors as well as designing novel devices. Recently, development of flexible electronic devices based on inorganic thin films on flexible substrates, which provides solutions to meet the emerging technological demands, may also expend the methodology of interface engineering. Herein, a semitransparent photodetector based on an indium-tin oxide (ITO)-on-silicon (Si) heterojunction was fabricated on a flexible substrate and investigated under mechanical bending strains. It is found that the barrier height of the heterojunction can be tailored continuously and reversibly from 0.23 eV to 0 eV, corresponding to the Schottky and Ohmic junctions respectively. Meanwhile, the turn-on voltage and the response time of the as-prepared photodetector can be obviously reduced under bending strain, which can be attributed to the modulation of the Si bandgap and hole mobility. Our experimental studies not only shed new light on the strain modulation mechanism of the heterojunction interface, but also pave a prominent way to integrated high-performance flexible photodetectors.

9.
Adv Sci (Weinh) ; 4(11): 1700251, 2017 11.
Artigo em Inglês | MEDLINE | ID: mdl-29201621

RESUMO

Soft neural electrode arrays that are mechanically matched between neural tissues and electrodes offer valuable opportunities for the development of disease diagnose and brain computer interface systems. Here, a thermal release transfer printing method for fabrication of stretchable bioelectronics, such as soft neural electrode arrays, is presented. Due to the large, switchable and irreversible change in adhesion strength of thermal release tape, a low-cost, easy-to-operate, and temperature-controlled transfer printing process can be achieved. The mechanism of this method is analyzed by experiments and fracture-mechanics models. Using the thermal release transfer printing method, a stretchable neural electrode array is fabricated by a sacrificial-layer-free process. The ability of the as-fabricated electrode array to conform different curvilinear surfaces is confirmed by experimental and theoretical studies. High-quality electrocorticography signals of anesthetized rat are collected with the as-fabricated electrode array, which proves good conformal interface between the electrodes and dura mater. The application of the as-fabricated electrode array on detecting the steady-state visual evoked potentials research is also demonstrated by in vivo experiments and the results are compared with those detected by stainless-steel screw electrodes.

10.
J Breath Res ; 11(3): 036002, 2017 Aug 08.
Artigo em Inglês | MEDLINE | ID: mdl-28786394

RESUMO

Real-time monitoring of breath can provide clinically relevant information about apnea syndrome and other important aspects of human physiology. Here, we introduce a flexible skin-like breath sensor developed by transfer-printing vanadium dioxide (VO2) thin films on PDMS substrates. This flexible breath sensor can conformably laminate on the skin under the nose with different curvatures and operate at different environment temperatures through day and night. Attributed to the high temperature coefficient of resistance of VO2, the enhanced breath sensing performance was demonstrated and the response time and recovery time can be as fast as 0.5 s. The excellent sensing performance and fast response time indicate that the VO2-based breath sensor is feasible in monitoring breath for prevention of apnea syndrome.


Assuntos
Testes Respiratórios/instrumentação , Óxidos/química , Compostos de Vanádio/química , Impedância Elétrica , Expiração , Humanos , Inalação , Processamento de Sinais Assistido por Computador , Temperatura
11.
Adv Healthc Mater ; 6(16)2017 Aug.
Artigo em Inglês | MEDLINE | ID: mdl-28493386

RESUMO

A new implantable capacitive electrode array for electrocorticography signal recording is developed with ferroelectric ceramic/polymer composite. This ultrathin and electrically safe capacitive electrode array is capable of attaching to the biological tissue conformably. The barium titanate/polyimide (BaTiO3 /PI) nanocomposite with high dielectric constant is successfully synthesized and employed as the ultrathin dielectric layer of the capacitive BaTiO3 /PI electrode array. The performance of the capacitive BaTiO3 /PI electrode array is evaluated by electrical characterization and 3D finite-element modeling. In vivo, neural experiments on the visual cortex of rats show the reliability of the capacitive BaTiO3 /PI electrode array. This work shows the potentials of capacitive BaTiO3 /PI electrode array in the field of brain/computer interfaces.


Assuntos
Eletrodos Implantados , Eletroencefalografia/instrumentação , Microeletrodos , Nanocompostos/química , Animais , Compostos de Bário/química , Cerâmica/química , Desenho de Equipamento , Análise de Elementos Finitos , Masculino , Polímeros/química , Ratos , Ratos Wistar , Reprodutibilidade dos Testes , Titânio/química , Córtex Visual/fisiologia , Córtex Visual/cirurgia
12.
Sci Rep ; 7: 42227, 2017 02 13.
Artigo em Inglês | MEDLINE | ID: mdl-28198812

RESUMO

Recent progresses on the Kirigami-inspired method provide a new idea to assemble three-dimensional (3D) functional structures with conventional materials by releasing the prestrained elastomeric substrates. In this paper, highly stretchable serpentine-like antenna is fabricated by a simple and quick "Cut-Transfer-Release" method for assembling stretchable 3D functional structures on an elastomeric substrate with a controlled shape. The mechanical reliability of the serpentine-like 3D stretchable antenna is evaluated by the finite element method and experiments. The antenna shows consistent radio frequency performance with center frequency at 5.6 GHz during stretching up to 200%. The 3D structure is also able to eliminate the hand effect observed commonly in the conventional antenna. This work is expected to spur the applications of novel 3D structures in the stretchable electronics.

13.
Nanoscale ; 8(18): 9592-9, 2016 May 14.
Artigo em Inglês | MEDLINE | ID: mdl-27101973

RESUMO

Different types of multi-walled carbon nanotubes (CNTs), synthesized by chemical vapor deposition, are used to fabricate infrared (IR) detectors on flexible substrates based on CNT p-n junctions. It is found that this kind of detector is sensitive to infrared signals with a power density as low as 90 µW mm(-2) even at room temperature. Besides, unlike other devices, the detector with this unique structure can be bent for 100 cycles without any damage and its functionality does not degenerate once it recovers to the initial state. The results give a good reference for developing efficient, low-cost, and flexible IR detectors.

SELEÇÃO DE REFERÊNCIAS
DETALHE DA PESQUISA
...