The optical property measuring methods for resin composite using multiple spectrophotometers.

This study aimed to propose the measurement methods for resin composite translucency using four shades of resin composite and four spectrophotometers. Four methods were used for measuring translucency: (A) color measurement using reflectance mode, (B) visible light spectrum measurement using reflectance mode, (C) color measurement using transmittance mode, (D) visible light spectrum measurement using transmittance mode. Although there was a significant difference among the results of the translucency measuring methods, the same tendency was observed for translucency parameters obtained using each spectrophotometer. Therefore, the four methods can potentially be used as translucency measuring methods for resin composite.

Correlation of two different devices for the evaluation of primary implant stability depending on dental implant length and bone density: An in vitro study.

Non-invasive objective implant stability measurements are needed to determine the appropriate timing of prosthetic fitting after implant placement. We compared the early implant stability results obtained using resonance frequency analysis (RFA) and damping capacity analysis (DCA) depending on the implant length and bone density. Total 60, 4.0 mm diameter implants of various lengths (7.3 mm, 10 mm, and 13 mm) were used. In Group I, low-density bone was described using 15 PCF (0.24 g/cm3) polyurethane bone blocks, and in Group II, 30 PCF (0.48 g/cm3) polyurethane bone blocks were used to describe medium density bone. RFA was performed using an Osstell® Beacon+; DCA was performed using Anycheck®. Measurements were repeated five times for each implant. Statistical significance was set at P <0.05. In Group I, bone density and primary implant stability were positively correlated, while implant length and primary implant stability were positively correlated. In Group II, the implant stability quotient (ISQ) and implant stability test (IST) values in did not change significantly above a certain length. Primary implant stability was positively correlated with bone density and improved with increasing implant length at low bone densities. Compared with the Osstell® Beacon+, the simplicity of Anycheck® was easy to use and accessible.

Shear bond strength of orthodontic brackets bonded with primer-incorporated orthodontic adhesives and unpolymerized 3-dimensional printing materials on 3-dimensional-printed crowns.

INTRODUCTION: The use of 3-dimensional (3D) printing techniques in fabricating crowns has increased the demand for bracket bonding onto these surfaces. The objective was to evaluate the shear bond strength (SBS) of orthodontic brackets bonded onto 3D-printed crowns using primer-incorporated orthodontic adhesives and 3D printing materials as orthodontic adhesives. METHODS: A total of 160 crowns were printed with two 3D printing materials, DentaTOOTH (Asiga, Sydney, Australia) (group A) and NextDent C&B Micro Filled Hybrid (3D Systems, Soesterberg, Netherlands) (group N). Each group was randomly divided into 4 adhesive subgroups (n = 20): Transbond XT (for groups A [ATX] and N [NTX]; 3M Unitek, Monrovia, Calif), Ortho Connect (for groups A [AOC] and N [NOC]; GC Corporation., Tokyo, Japan), Orthomite LC (for groups A [AOM] and N [NOM]; Sun Medical, Co Ltd, Moriyama, Shiga, Japan), and unpolymerized liquid state of 3D printing resin (for groups A [AA] and N [NN]). SBS was measured with a universal testing machine at a crosshead speed of 0.5 mm/min. The adhesive remnant index and the mode of failure were analyzed under the microscope. Statistical analysis was performed at a significance level of α = 0.05. RESULTS: When used as adhesives (AA and NN), 3D printing materials showed no statistically significant difference in SBS compared with Transbond XT (ATX and NTX, respectively). In group N, NN showed a significantly higher SBS than primer-incorporated orthodontic adhesives (NOC and NOM; P <0.001). Adhesive failures were only observed in primer-incorporated orthodontic adhesives (AOC, NOC, AOM, and NOM). CONCLUSIONS: Primer-incorporated orthodontic adhesives, as well as unpolymerized 3D printing materials employed as orthodontic adhesives on 3D-printed crowns, exhibited comparable bonding strength to Transbond XT without surface modification. Despite variations in adhesive-related factors, all measurements stayed within clinically acceptable ranges, highlighting the potential of these materials for orthodontic bonding on 3D-printed crowns, simplifying clinical procedures without compromising bond strength.

Managing oral biofilms to avoid enamel demineralization during fixed orthodontic treatment.

Enamel demineralization represents the most prevalent complication arising from fixed orthodontic treatment. Its main etiology is the development of cariogenic biofilms formed around orthodontic appliances. Ordinarily, oral biofilms exist in a dynamic equilibrium with the host's defense mechanisms. However, the equilibrium can be disrupted by environmental changes, such as the introduction of a fixed orthodontic appliance, resulting in a shift in the biofilm's microbial composition from non-pathogenic to pathogenic. This alteration leads to an increased prevalence of cariogenic bacteria, notably mutans streptococci, within the biofilm. This article examines the relationships between oral biofilms and orthodontic appliances, with a particular focus on strategies for effectively managing oral biofilms to mitigate enamel demineralization around orthodontic appliances.

Cytotoxicity and reactive oxygen species production induced by different co-monomer eluted from nanohybrid dental composites.

BACKGROUND: Safety issues for dental restorative composites are critical to material selection, but, limited information is available to dental practitioners. This study aimed to compare the chemical and biological characteristics of three nanohybrid dental composites by assessing filler particle analysis, monomer degree of conversion (DC), the composition of eluates, and cytotoxicity and reactive oxygen species (ROS) production in fibroblasts. METHODS: Three nanohybrid composites (TN, Tetric N-Ceram; CX, Ceram X Sphere Tec One; and DN, DenFil NX) were used. The size distribution and morphology of the filler particles were analysed using scanning electron microscopy (n = 5). The DC was measured via micro-Raman spectroscopy (n = 5). For the component analysis, methanol eluates from the light-polymerised composites were evaluated by gas chromatography/mass spectrometry (n = 3). The eluates were prepared from the polymerised composites after 24 h in a cell culture medium. A live/dead assay (n = 9) and Water-Soluble Tetrazolium-1 assay (n = 9) were performed and compared with negative and positive controls. The ROS in composites were compared with NC. Statistical significance in differences was assessed using a t-test and ANOVA (α = 0.05). RESULTS: Morphological variations in different-sized fillers were observed in the composites. The DC values were not significantly different among the composites. The amounts of 2-hydroxyethyl methacrylate (HEMA) were higher in TN than DN (p = 0.0022) and triethylene glycol dimethacrylate (TEGDMA) in CX was higher than in others (p < 0.0001). The lowest cell viability was shown in CX (p < 0.0001) and the highest ROS formation was detected in TN (p < 0.0001). CONCLUSIONS: Three nanohybrid dental composites exhibited various compositions of filler sizes and resin components, resulting in different levels of cytotoxicity and ROS production. Chemical compositions of dental composites can be considered with their biological impact on safety issues in the intraoral use of dental restorative composites. CX with the highest TEGDMA showed the highest cytotoxicity induced by ROS accumulation. DN with lower TEGDMA and HEMA presented the highest cell viability.

Effects of RGD-grafted phosphatidylserine-containing liposomes on the polarization of macrophages and bone tissue regeneration.

Phosphatidylserine-containing liposomes (PSLs) can mimic the anti-inflammatory effects of apoptotic cells by binding to the phosphatidylserine receptors of macrophages. MGF-E8, a bridge molecule between phosphatidylserine and macrophages, can promote M2 polarization by activating macrophage integrin with its arginine-glycine-aspartic acid (RGD) motif. In this study, to mimic MGF-E8, PSLs presenting RGD peptide (RGD-PSLs) were prepared, and their immunomodulatory effects on macrophages and the bone tissue regeneration of rat calvarial defects were investigated. RGD peptides enhanced the phagocytosis of PSLs by macrophages, especially when the PSLs contained 3% RGD. RGD-PSLs were also more effective than PSLs for the suppression of lipopolysaccharide-induced gene expression of proinflammatory cytokines (i.e., IL-1ß, IL-6, and TNF-α) as well as CD86 (M1 marker) expression. Furthermore, RGD promoted PSL-induced M2 polarization: 3%-RGD-PSLs significantly enhanced the mRNA expression of Arg-1, FIZZ1, and YM-1, as well as CD206 (M2 marker) expression. In a calvarial defect model, a significant increase in M2 with a decrease in M1 macrophages was observed with 3%-RGD-PSL treatment compared with the effects of PSLs alone. Finally, new bone formation was also accelerated by 3%-RGD-PSLs. Thus, these results suggest that the intensive immunomodulatory effect of RGD-PSLs led to the enhancement of bone tissue regeneration.

Influence of Additive Firing on the Surface Characteristics, Streptococcus mutans Viability and Optical Properties of Zirconia.

The purpose of this study was to observe whether the repetitive firing of dental zirconia caused changes in surface characteristics, S. mutans viability, and optical properties of zirconia. Dental zirconia blocks were sintered and randomly distributed into seven experimental groups: F0-F6. Except for F0, which only went through sintering, the additive firing was performed in order for F1-F6. Surface roughness, contact angle, S. mutans viability by fluorescence, and translucency parameter were measured. They were all highest after sintering (F0) and decreased after additive firings (F1-F6). The additive firing of zirconia after sintering decreased surface roughness, contact angle, S. mutans viability, and translucency. The number of firings after the first firing was not found to be critical in surface characteristics, S. mutans viability, and optical property. Changes in surface characteristics might have led to a decrease in S. mutans viability, while the change of translucency was not clinically significant. This implies that additive firing may prevent secondary caries under zirconia restorations, not compromising esthetic appearance.

Dimensional Accuracy Evaluation of Temporary Dental Restorations with Different 3D Printing Systems.

With the advent of 3D printing technologies in dentistry, the optimization of printing conditions has been of great interest, so this study analyzed the accuracy of 3D-printed temporary restorations of different sizes produced by digital light processing (DLP) and liquid crystal display (LCD) printers. Temporary restorations of 2-unit, 3-unit, 5-unit, 6-unit, and full-arch cases were designed and printed from a DLP printer using NextDent C&B or an LCD printer using Mazic D Temp (n = 10 each). The restorations were scanned, and each restoration standard tessellation language (STL) file was superimposed on the reference STL file, by the alignment functions, to evaluate the trueness through whole/point deviation. In the whole-deviation analysis, the root-mean-square (RMS) values were significantly higher in the 6-unit and full-arch cases for the DLP printer and in the 5-unit, 6-unit, and full-arch cases for the LCD printer. The significant difference between DLP and LCD printers was found in the 5-unit and full-arch cases, where the DLP printer exhibited lower RMS values. Color mapping demonstrated less shrinkage in the DLP printer. In the point deviation analysis, a significant difference in direction was exhibited in all the restorations from the DLP printer but only in some cases from the LCD printer. Within the limitations of this study, 3D printing was most accurate with less deviation and shrinkage when a DLP printer was used for short-unit restorations.

Urethane Dimethacrylate Influences the Cariogenic Properties of Streptococcus Mutans.

Concerns regarding unbound monomers in dental composites have increased with the increased usage of these materials. This study assessed the biological effects of urethane dimethacrylate (UDMA), a common monomer component of dental composite resins, on the cariogenic properties of Streptococcus mutans. Changes in the growth rate, biofilm formation, interaction with saliva, surface hydrophobicity, adhesion, glucan synthesis, sugar transport, glycolytic profiles, and oxidative- and acid-stress tolerances of S. mutans were evaluated after growing the cells in the presence and absence of UDMA. The results indicated that UDMA promotes the adhesion of S. mutans to the underlying surfaces and extracellular polysaccharide synthesis, leading to enhanced biofilm formation. Furthermore, UDMA reduced the acid tolerance of S. mutans, but enhanced its tolerance to oxidative stress, thus favoring the early stage of biofilm development. UDMA did not significantly affect the viability or planktonic growth of cells, but diminished the ability of S. mutans to metabolize carbohydrates and thus maintain the level of intracellular polysaccharides, although the tendency for sugar transport increased. Notably, UDMA did not significantly alter the interactions of bacterial cells with saliva. This study suggests that UDMA may potentially contribute to the development of secondary caries around UDMA-containing dental materials by prompting biofilm formation, enhancing oxidative tolerance, and modulating carbon flow.

Effects of Caries Activity on Compositions of Mutans Streptococci in Saliva-Induced Biofilm Formed on Bracket Materials.

This study aimed to investigate effects of caries activity on composition of mutans streptococci in saliva-induced biofilms formed on bracket materials. Three bracket materials were used as specimens: ceramic, metal, and plastic. After saliva was collected using a spitting method from caries-active (CA, decayed, missing, filled teeth (DMFT) score ≥ 10) and caries-free (CF, DMFT score = 0) subjects, saliva was mixed with growth media in a proportion of 1:10. The saliva solution was then incubated with each bracket material. After a saliva-induced biofilm was developed on the surface of the bracket material, the amounts of total bacteria and mutans streptococci were determined using real-time polymerase chain reaction. The results showed that biofilms from CA saliva contained more mutans streptococci but less total bacteria than biofilms from CF saliva, regardless of material type. Adhesion of total bacteria to ceramic was higher than to plastic, regardless of caries activity. Mutans streptococci adhered more to ceramic than to metal and plastic in both biofilms from CA and CF saliva, but there was a difference in adhesion between Streptococcus mutans and Streptococcus sobrinus. The amount of S. mutans was higher than that of S. sobrinus in biofilms from CA saliva despite similar amounts of the two strains in biofilms from CF saliva. The stronger adhesion of S. mutans to ceramic than to metal and plastic was more evident in biofilms from CA saliva than in biofilms from CF saliva. This study suggests that caries activity and material type significantly influenced composition of mutans streptococci in biofilms formed on bracket materials.

Color Stability of Dental Reinforced CAD/CAM Hybrid Composite Blocks Compared to Regular Blocks.

This study compares the color stability of dental reinforced computer-aided design/computer-aided manufacturing (CAD/CAM) hybrid composite blocks to that of regular blocks. One hundred fifty disc-type specimens (n = 15) were prepared from five sets of hybrid composite blocks (Cerasmart-200/Cerasmart-300, KZR-CAD HR/KZR-CAD HR3, Estelite Block/ Estelite-P Block, Avencia Block/Avencia-P Block, Mazic Duro/Duro Ace). The specimen color and translucency parameter (TP) were assessed using a spectrophotometer before and after immersion in staining solutions (water, 10% ethanol, simulated red wine). Changes in color (ΔE) and translucency (ΔTP) of specimens were calculated. The data were analyzed using the analysis of variance (ANOVA) and Tukey's post hoc test (p < 0.05). Microstructural features of the hybrid composite blocks were also examined using FE-SEM. Immersion in deionized water or 10% ethanol made no significant color or translucency changes (except for Avencia-P Block); however, the simulated red wine caused significant changes to the color and translucency of almost all specimens, especially after 4 weeks of immersion. The reinforced hybrid blocks (except for Estelite-P Block and Duro Ace) showed lower color stability than corresponding regular blocks. Avencia-P Block showed significantly reduced color stability compared to Avencia Block. Even in deionized water and 10% ethanol, Avencia-P Block showed perceptible ΔE and decreased translucency. Estelite Block/ Estelite-P Block and Mazic Duro/Duro Ace showed better color stability than the other materials tested.

Primer-Treated Ceramic Bracket Increases Shear Bond Strength on Dental Zirconia Surface.

The purpose of this study is to evaluate the shear bond strength (SBS) of a primer-treated ceramic bracket on dental zirconia and to compare it with conventional ceramic bracket bonding on surface-treated zirconia. Sintered and finished dental zirconia was sandblasted. Samples were divided according to the treated surfaces: no treatment (X), ceramic primer on zirconia (Z), ceramic primer on bracket base (B), and ceramic primer on both zirconia and bracket base (ZB). The ceramic bracket was bonded on zirconia and SBS was measured before (T0) and after 10,000 cycles of thermocycling (Tf). The failed surfaces were examined under field emission scanning electron microscope (FE-SEM), and adhesive remnant index (ARI) was evaluated. SBS was significantly higher in ZB and significantly lower in X in both T0 and Tf. There was no significant difference between Z and B. In X and B, adhesive failure occurred while ZB showed mixed failures. There was no apparent change in the zirconia surface except for the existence of some adhesive and resin remnants. The application of ceramic primer on the bracket base increased the bonding strength to the level of conventional bonding with fewer adhesive remnants. The highest bonding strength was obtained when the primer-treated bracket was bonded on the primer-treated zirconia.

Orthodontic bonding procedures significantly influence biofilm composition.

BACKGROUND: Because changes in surface properties affect bacterial adhesion, orthodontic bonding procedures may significantly influence biofilm formation and composition around orthodontic appliances. However, most studies used a mono-species biofilm model under static conditions, which does not simulate the intraoral environment and complex interactions of oral microflora because the oral cavity is a diverse and changeable environment. In this study, a multi-species biofilm model was used under dynamic culture conditions to assess the effects of the orthodontic bonding procedure on biofilm formation and compositional changes in two main oral pathogens, Streptococcus mutans and Porphyromonas gingivalis. METHODS: Four specimens were prepared with bovine incisors and bonding adhesive: untreated enamel surface (BI), enamel surface etched with 37% phosphoric acid (ET), primed enamel surface after etching (PR), and adhesive surface (AD). Surface roughness (SR), surface wettability (SW), and surface texture were evaluated. A multi-species biofilm was developed on each surface and adhesion amounts of Streptococcus mutans, Porphyromonas gingivalis, and total bacteria were analyzed at day 1 and day 4 using real-time polymerase chain reaction. After determining the differences in biofilm formation, SR, and SW between the four surfaces, relationships between bacteria levels and surface properties were analyzed. RESULTS: The order of SR was AD < PR < BI < ET, as BI and ET showed more irregular surface texture than PR and AD. For SW, ET had the greatest value followed by PR, BI, and AD. S. mutans and P. gingivalis showed greater adhesion to BI and ET with rougher and more wettable surfaces than to AD with smoother and less wettable surfaces. The adhesion of total bacteria and S. mutans significantly increased over time, but the amount of P. gingivalis decreased. The adhesion amounts of all bacteria were positively correlated with SR and SW, irrespective of incubation time. CONCLUSIONS: Within the limitations of this study, changes in SR and SW associated with orthodontic bonding had significant effects on biofilm formation and composition of S. mutans and P. gingivalis.

Microbial changes in biofilms on composite resins with different surface roughness: An in vitro study with a multispecies biofilm model.

STATEMENT OF PROBLEM: The single-species biofilm method cannot represent the interaction and complex functions of microorganisms associated with oral biofilms. PURPOSE: The purpose of this in vitro study was to investigate microbial changes in biofilms on composite resins of varying surface roughness by using a multispecies biofilm model with early-colonizing streptococci, middle colonizer, and late-colonizing gram-negative anaerobes. MATERIAL AND METHODS: Composite resin disks were prepared with different roughness: SR180, SR400, SR1500, and SRGlass roughened with 180-, 400-, and 1500-grit silicon carbide paper and glass (control surface without surface roughening). Surface roughness was analyzed by confocal laser scanning and scanning electron microscopy. After multispecies biofilms had been grown on the composite resin surfaces, the adhesion of Streptococcus mutans, Streptococcus sobrinus, Porphyromonas gingivalis, Aggregatibacter actinomycetemcomitans, and of total bacteria was determined after 1 (T1) and 4 (T2) days. Differences in surface roughness among the 4 groups were tested with 1-way ANOVA. Multifactorial analysis of variance was used to determine the time-related differences in the bacterial composition with respect to surface roughness (α=.05). RESULTS: The order of SR, from highest to lowest, was SR180 (1.45 ±0.11 µm), SR400 (0.62 ±0.05 µm), SR1500 (0.35 ±0.02 µm), and SRGlass (0.15 ±0.01 µm) (SR180>SR400>SR1500>SRGlass, P<.001). Increased surface roughness was not proportional to bacterial adhesion. Significant differences in the adhesion of total bacteria was only found between SRGlass and SR180 (SR180>SRGlass, P=.029). The adhesion of S. mutans and S. sobrinus to SR180 and SR400 was higher than that to SRGlass (SR180=SR400>SRGlass; S. mutans, P=.003; S. sobrinus, P=.002). However, the adhesion of A. actinomycetemcomitans and P. gingivalis to composite resin was not significantly influenced by surface roughness. Adhesion of total bacteria, S. mutans, and S. sobrinus increased from T1 to T2 (T1T2; A. actinomycetemcomitans, P<.001; P. gingivalis, P=.013). CONCLUSIONS: Decreased adhesion of cariogenic streptococci and total bacteria was observed at surface roughness values of around 0.15 µm. Periodic finishing of surface roughness should be considered to minimize the adhesion of cariogenic streptococci to composite resin surfaces.

Effect of Simplified Bonding on Shear Bond Strength between Ceramic Brackets and Dental Zirconia.

The aim of this study was to evaluate the long term stability of shear bond strength (SBS) when 10-methacryloyloxydecyl dihydrogen phosphate (10-MDP) containing universal adhesive was used in the ceramic bracket bonding on dental zirconia. Twenty human maxillary incisors were collected. The ceramic bracket was bonded on the buccal enamel surface after the acid-etching and orthodontic primer application (Group CON). Sixty zirconia specimens were sintered, sandblasted and divided into three experimental groups; group CP-ceramic primer followed by an orthodontic primer; group U-universal adhesive; group CU-ceramic primer followed by a universal adhesive. For each specimen, the bracket was bonded onto the treated surface with composite resin (Transbond XT, 3M ESPE). The SBS tested before (CON0, CP0, U0, CU0) and after the artificial aging (CON1, CP1, U1, CU1). The data were statistically analyzed with the Kruskal-Wallis test at a significance level of 0.05. The mean SBS of CON0, CP0, U0 and CU0 were within the clinically acceptable range without significant differences. After the aging process, SBS decreased in all groups. Among the aged groups, CP1 showed the highest SBS. Based on the results, when bonding ceramic brackets to a dental zirconia surface, we can conclude that ceramic primer used with an orthodontic primer, rather than using a universal adhesive, is recommended.

Effect of Bisphenol A Glycol Methacrylate on Virulent Properties of Streptococcus mutans UA159.

Bisphenol A glycidyl methacrylate (bis-GMA), which is released into the oral environment by dental composites through incomplete polymerization, hydrolysis, and mechanical degradation, can significantly influence oral ecology around resin-based materials. The purpose of this study was to investigate how bis-GMA changes the virulence properties of Streptococcus mutans, a major cariogenic bacterium in humans. The results show that bis-GMA not only inhibited the planktonic growth of cells in medium containing glucose, fructose, or mannose, but also reduced the viability of S. mutans. However, the presence of bis-GMA increased sugar transport and intracellular polysaccharide accumulation in S. mutans, thereby increasing the potential of cell persistence. In addition, bis-GMA could enhance S. mutans's adhesion to hard surfaces and glucan synthesis, which could contribute to biofilm formation. Although free bis-GMA made cells vulnerable to acidic stress, it also provided increased resistance to hydrogen peroxide, which might confer an advantage in competition with other oral microorganisms during the early stage of biofilm development. Interestingly, the presence of bis-GMA did not change the ability of S. mutans to interact with saliva. The results suggest that leachable bis-GMA could contribute to biofilm-related secondary dental caries at the marginal interface between resin-based materials and teeth by altering the virulent properties of S. mutans, although bis-GMA reduced the planktonic growth and viability of S. mutans.

Compositional differences in multi-species biofilms formed on various orthodontic adhesives.

OBJECTIVES: To investigate the aspects of multi-species biofilm formation on various orthodontic adhesives with different surface characteristics. METHODS: Multi-species biofilms using 13 bacterial species were grown on the surfaces of composite, compomer, and resin-modified glass-ionomer cement (RMGI). The changes in Streptococcus mutans (Sm), Streptococcus sobrinus (Ss), Porphyromonas gingivalis (Pg), Aggregatibacter actinomycetemcomitans (Aa), and total bacteria were determined at day 1 (T1) and day 4 (T2) using real-time polymerase chain reaction. Surface roughness (SR), surface free energy (SFE), and surface texture were analyzed to explain the differences in bacterial compositions among the adhesives. Repeated measures analysis of variance was used to determine time-related changes in bacterial compositions with respect to adhesive type. The Kruskal-Wallis test was used to determine differences in SR and SFE among the adhesives. RESULTS: There were no significant differences in the adhesion of total bacteria among the adhesives; however, the adhesion of Sm, Ss, and Pg was higher to RMGI than the other adhesives. The amount of Sm, Ss, and total bacteria increased from T1 to T2, while Pg and Aa decreased from T1 to T2. RMGI showed a rougher surface relative to composite or compomer due to the presence of micro-pores and/or flaws. Compomer had the greatest SFE followed by RMGI and composite. Interestingly, SR differences were about 10 times greater than SFE differences among the adhesives. CONCLUSIONS: Considering the greater differences in SR than SFE among the adhesives, the rougher surface of RMGI may cause greater adhesion of Sm, Ss, and Pg.

Antimicrobial and physical characteristics of orthodontic primers containing antimicrobial agents.

OBJECTIVE: To compare the antimicrobial and physical properties of experimental primers containing chlorhexidine (CHX) or ursolic acid (UA) with a commercial primer. MATERIALS AND METHODS: Two antibacterial agents, 3 mg each of CHX and UA were incorporated respectively into 1 ml of Transbond XT primer (TX) to form antibacterial primers, TX-CHX and TX-UA. The antimicrobial activity of the three primers (TX, TX-CHX, and TX-UA) against Streptococcus mutans in both planktonic and biofilm phases was analyzed by determining minimum inhibitory and bactericidal concentrations and by performing growth and biofilm assays. Growth and biofilm assays were performed in both the absence and presence of thermocycling in a water tank to analyze the effects of water aging on the antimicrobial activities of primers. After bonding brackets onto bovine incisors using the primers, shear bond strength and mode of fracture were analyzed to compare physical properties. RESULTS: TX-CHX had stronger antimicrobial activity against S. mutans in the planktonic and biofilm phases than did TX or TX-UA. When applied, TX-CHX completely inhibited the growth and biofilm formation of S. mutans . In addition, the antimicrobial activity of TX-CHX was maintained after thermocycling. However, TX-UA did not show significant antimicrobial activity compared with TX. There was no significant difference in either shear bond strength or bond failure interface among the primers. CONCLUSION: Incorporation of CHX into an orthodontic primer may help prevent enamel demineralization around surfaces without compromising its physical properties.

Frictional property comparisons of conventional and self-ligating lingual brackets according to tooth displacement during initial leveling and alignment: an in vitro mechanical study.

OBJECTIVE: We evaluated the effects of tooth displacement on frictional force when conventional ligating lingual brackets (CL-LBs), CL-LBs with a narrow bracket width, and self-ligating lingual brackets (SL-LBs) were used with initial leveling and alignment wires. METHODS: CL-LBs (7th Generation), CL-LBs with a narrow bracket width (STb), and SL-LBs (In-Ovation L) were tested under three tooth displacement conditions: no displacement (control); a 2-mm palatal displacement (PD) of the maxillary right lateral incisor (MXLI); and a 2-mm gingival displacement (GD) of the maxillary right canine (MXC) (nine groups, n = 7 per group). A stereolithographic typodont system and artificial saliva were used. Static and kinetic frictional forces (SFF and KFF, respectively) were measured while drawing a 0.013-inch copper-nickel-titanium archwire through brackets at 0.5 mm/min for 5 minutes at 36.5℃. RESULTS: The In-Ovation L exhibited lower SFF under control conditions and lower KFF under all displacement conditions than the 7th Generation and STb (all p < 0.001). No significant difference in SFF existed between the In-Ovation L and STb for a 2-mm GD of the MXC and 2-mm PD of the MXLI. A 2-mm GD of the MXC produced higher SFF and KFF than a 2-mm PD of the MXLI in all brackets (all p < 0.001). CONCLUSIONS: CL-LBs with narrow bracket widths exhibited higher KFF than SL-LBs under tooth displacement conditions. CL-LBs and ligation methods should be developed to produce SFF and KFF as low as those in SL-LBs during the initial and leveling stage.