Ultralow-threshold quasi-CW lasing from FAPbBr3perovskite first-order DFB laser.

Metal halide perovskites are emerging materials for integrated photonics. Here we report a quasi-CW pumped ultra-low ASE/lasing threshold formamidinium lead bromide (FAPbBr3) laser. The laser achieved stable lasing at 555 nm with a full width at half maximum (FWHM) of 0.6 nm, showing a low lasing threshold of 22.6µJ cm-2under 3.5 nanosecond quasi-CW excitation at room temperature. The material also showed an ultra-low ASE threshold of 46µJ cm-2under the same pumping condition. Through polymer doping, we showed that the material's performance can be improved by increasing bimolecular recombination rate with reduced grain size.

Effect of emitter orientation on the outcoupling efficiency of perovskite light-emitting diodes.

Metal halide perovskite light-emitting diodes (PeLEDs) have experienced a rapid advancement in the last several years with the external quantum efficiencies (EQEs) reaching over 20%, comparable to the state-of-the-art organic LEDs and quantum dot LEDs. The photoluminescence quantum yields of perovskite films have also been approaching 100%. Therefore, the next step to improving the EQE of PeLEDs should be focused on boosting light extraction. In this Letter, we demonstrate the emitter dipole orientation as a key parameter in determining the outcoupling efficiency of PeLEDs. We find that the CsPbBr3 emitter has a slightly preferred orientation with the horizontal-to-vertical dipole ratio of 0.41:0.59, as compared to 0.33:0.67 in the isotropic case. A theoretical analysis predicts that a purely anisotropic perovskite emitter may result in a maximum EQE of 36%.

Suppressing Efficiency Roll-Off at High Current Densities for Ultra-Bright Green Perovskite Light-Emitting Diodes.

Perovskite light-emitting diodes (PeLEDs) have undergone rapid development in the last several years with external quantum efficiencies (EQEs) reaching over 21%. However, most PeLEDs still suffer from severe efficiency roll-off (droop) at high injection current densities, thus limiting their achievable brightness and presenting a challenge to their use in laser diode applications. In this work, we show that the roll-off characteristics of PeLEDs are affected by a combination of charge injection imbalance, nonradiative Auger recombination, and Joule heating. To realize ultrabright and efficient PeLEDs, several strategies have been applied. First, we designed an energy ladder to balance the electron and hole transport. Second, we optimized perovskite materials to possess reduced Auger recombination rates and improved carrier mobility. Third, we replaced glass substrates with sapphire substrates to better dissipate joule heat. Finally, by applying a current-focusing architecture, we achieved PeLEDs with a record luminance of 7.6 Mcd/m2. The devices can be operated at very high current densities (J) up to ∼1 kA/cm2. Our work suggests a broad application prospect of perovskite materials for high-brightness LEDs and ultimately a potential for solution-processed electrically pumped laser diodes.

Photolithographic Patterning of Perovskite Thin Films for Multicolor Display Applications.

Metal halide perovskites are emerging as attractive materials for light-emitting diode (LED) applications. The external quantum efficiency (EQE) has experienced a rapid progress and reached over 21%, comparable to the state of the art organic and quantum dot LEDs. For metal halide perovskites, their simple solution-processing preparation, facile band gap tunability, and narrow emission line width provide another attractive route to harness their superior optoelectronic properties for multicolor display applications. In this work, we demonstrate a high-resolution, large-scale photolithographic method to pattern multicolor perovskite films. This approach is based on a dry lift-off process which involves the use of parylene as an intermediary and the easy mechanical peeling-off of parylene films on various substrates. Using this approach, we successfully fabricated multicolor patterns with red and green perovskite pixels on a single substrate, which could be further applied in liquid crystal displays (LCDs) with blue backlight. Besides, a prototype green perovskite micro-LED display under current driving has been demonstrated.

Subwavelength optical trapping and transporting using a Bloch mode.

Multi-functional optical manipulations, including optical trapping and transporting of subwavelength particles, are proposed using the Bloch modes in a dielectric photonic structure. We show that the Bloch modes in a periodic structure can generate a series of subwavelength trapping wells that are addressable by tuning the incident wavelength. This feature enables efficient optical trapping and transportation in a peristaltic way. Since we are using the guiding Bloch mode in a dielectric structure, rather than using plasmonic or dielectric resonant cavities, these operations are wide band and free from joule loss. The Bloch mode in a simple periodic dielectric structure provides a new platform for multi-functional optical operations and may find potential applications in nanophotonics and biomedicine.

Targeted Ligand-Exchange Chemistry on Cesium Lead Halide Perovskite Quantum Dots for High-Efficiency Photovoltaics.

The ability to manipulate quantum dot (QD) surfaces is foundational to their technological deployment. Surface manipulation of metal halide perovskite (MHP) QDs has proven particularly challenging in comparison to that of more established inorganic materials due to dynamic surface species and low material formation energy; most conventional methods of chemical manipulation targeted at the MHP QD surface will result in transformation or dissolution of the MHP crystal. In previous work, we have demonstrated record-efficiency QD solar cells (QDSCs) based on ligand-exchange procedures that electronically couple MHP QDs yet maintain their nanocrystalline size, which stabilizes the corner-sharing structure of the constituent PbI64- octahedra with optoelectronic properties optimal for solar energy conversion. In this work, we employ a variety of spectroscopic techniques to develop a molecular-level understanding of the MHP QD surface chemistry in this system. We individually target both the anionic (oleate) and cationic (oleylammonium) ligands. We find that atmospheric moisture aids the process by hydrolysis of methyl acetate to generate acetic acid and methanol. Acetic acid then replaces native oleate ligands to yield QD surface-bound acetate and free oleic acid. The native oleylammonium ligands remain throughout this film deposition process and are exchanged during a final treatment step employing smaller cations-namely, formamidinium. This final treatment has a narrow processing window; initial treatment at this stage leads to a more strongly coupled QD regime followed by transformation into a bulk MHP film after longer treatment. These insights provide chemical understanding to the deposition of high-quality, electronically coupled MHP QD films that maintain both quantum confinement and their crystalline phase and attain high photovoltaic performance.

Optical tweezers system for live stem cell organization at the single-cell level.

Cell manipulation is one of the most impactful applications for optical tweezers, and derived from this promise, we demonstrate a new optical tweezers system for the study of cell adhesion and organization. This method utilizes photonic-crystal-enhanced optical tweezers to manipulate cells with low laser intensities. By doing so, it enables effective cell patterning and culturing within the conditions necessary for successful differentiation and colony formation of human pluripotent stem cells. To this end, the biocompatibility of plasma-treated parylene-C for cell culturing was studied, and a thorough characterization of cellular interactive forces was performed using this system. Furthermore, this study also demonstrates construction of patterned cell arrays at arbitrary positions with micrometer-scale precision.

Enhanced mobility CsPbI3 quantum dot arrays for record-efficiency, high-voltage photovoltaic cells.

We developed lead halide perovskite quantum dot (QD) films with tuned surface chemistry based on A-site cation halide salt (AX) treatments. QD perovskites offer colloidal synthesis and processing using industrially friendly solvents, which decouples grain growth from film deposition, and at present produce larger open-circuit voltages (VOC's) than thin-film perovskites. CsPbI3 QDs, with a tunable bandgap between 1.75 and 2.13 eV, are an ideal top cell candidate for all-perovskite multijunction solar cells because of their demonstrated small VOC deficit. We show that charge carrier mobility within perovskite QD films is dictated by the chemical conditions at the QD-QD junctions. The AX treatments provide a method for tuning the coupling between perovskite QDs, which is exploited for improved charge transport for fabricating high-quality QD films and devices. The AX treatments presented here double the film mobility, enabling increased photocurrent, and lead to a record certified QD solar cell efficiency of 13.43%.

Highly stable cesium lead iodide perovskite quantum dot light-emitting diodes.

Recently, all-inorganic perovskites such as CsPbBr3 and CsPbI3, have emerged as promising materials for light-emitting applications. While encouraging performance has been demonstrated, the stability issue of the red-emitting CsPbI3 is still a major concern due to its small tolerance factor. Here we report a highly stable CsPbI3 quantum dot (QD) light-emitting diode (LED) with red emission fabricated using an improved purification approach. The device achieved decent external quantum efficiency (EQE) of 0.21% at a bias of 6 V and outstanding operational stability, with a L 70 lifetime (EL intensity decreases to 70% of starting value) of 16 h and 1.5 h under a constant driving voltage of 5 V and 6 V (maximum EQE operation) respectively. Furthermore, the device can work under a higher voltage of 7 V (maximum luminance operation) and retain 50% of its initial EL intensity after 500 s. These findings demonstrate the promise of CsPbI3 QDs for stable red LEDs, and suggest the feasibility for electrically pumped perovskite lasers with further device optimizations.

Gene-Edited Human Kidney Organoids Reveal Mechanisms of Disease in Podocyte Development.

A critical event during kidney organogenesis is the differentiation of podocytes, specialized epithelial cells that filter blood plasma to form urine. Podocytes derived from human pluripotent stem cells (hPSC-podocytes) have recently been generated in nephron-like kidney organoids, but the developmental stage of these cells and their capacity to reveal disease mechanisms remains unclear. Here, we show that hPSC-podocytes phenocopy mammalian podocytes at the capillary loop stage (CLS), recapitulating key features of ultrastructure, gene expression, and mutant phenotype. hPSC-podocytes in vitro progressively establish junction-rich basal membranes (nephrin+ podocin+ ZO-1+ ) and microvillus-rich apical membranes (podocalyxin+ ), similar to CLS podocytes in vivo. Ultrastructural, biophysical, and transcriptomic analysis of podocalyxin-knockout hPSCs and derived podocytes, generated using CRISPR/Cas9, reveals defects in the assembly of microvilli and lateral spaces between developing podocytes, resulting in failed junctional migration. These defects are phenocopied in CLS glomeruli of podocalyxin-deficient mice, which cannot produce urine, thereby demonstrating that podocalyxin has a conserved and essential role in mammalian podocyte maturation. Defining the maturity of hPSC-podocytes and their capacity to reveal and recapitulate pathophysiological mechanisms establishes a powerful framework for studying human kidney disease and regeneration. Stem Cells 2017;35:2366-2378.

Ultrathin (<1 µm) Substrate-Free Flexible Photodetector on Quantum Dot-Nanocellulose Paper.

Conventional approaches to flexible optoelectronic devices typically require depositing the active materials on external substrates. This is mostly due to the weak bonding between individual molecules or nanocrystals in the active materials, which prevents sustaining a freestanding thin film. Herein we demonstrate an ultrathin freestanding ZnO quantum dot (QD) active layer with nanocellulose structuring, and its corresponding device fabrication method to achieve substrate-free flexible optoelectronic devices. The ultrathin ZnO QD-nanocellulose composite is obtained by hydrogel transfer printing and solvent-exchange processes to overcome the water capillary force which is detrimental to achieving freestanding thin films. We achieved an active nanocellulose paper with ~550 nm thickness, and >91% transparency in the visible wavelength range. The film retains the photoconductive and photoluminescent properties of ZnO QDs and is applied towards substrate-free Schottky photodetector applications. The device has an overall thickness of ~670 nm, which is the thinnest freestanding optoelectronic device to date, to the best of our knowledge, and functions as a self-powered visible-blind ultraviolet photodetector. This platform can be readily applied to other nano materials as well as other optoelectronic device applications.

Silicon Quantum Dot Nanoparticles with Antifouling Coatings for Immunostaining on Live Cancer Cells.

Fluorescent silicon quantum dots (SiQDs) have shown a great potential as antiphotobleaching, nontoxic and biodegradable labels for various in vitro and in vivo applications. However, fabricating SiQDs with high water-solubility and high photoluminescence quantum yield (PLQY) remains a challenge. Furthermore, for targeted imaging, their surface chemistry has to be capable of conjugating to antibodies, as well as sufficiently antifouling. Herein, antibody-conjugated SiQD nanoparticles (SiQD-NPs) with antifouling coatings composed of bovine serum albumin (BSA) and polyethylene glycol (PEG) are demonstrated for immunostaining on live cancer cells. The monodisperse SiQD-NPs of diameter about 130 nm are synthesized by a novel top-down method, including electrochemical etching, photochemical hydrosilylation, high energy ball milling, and "selective-etching" in HNO3 and HF. Subsequently, the BSA and PEG are covalently grafted on to the SiQD-NP surface through presynthesized chemical linkers, resulting in a stable, hydrophilic, and antifouling organic capping layer with isothiocyanates as the terminal functional groups for facile conjugation to the antibodies. The in vitro cell viability assay reveals that the BSA-coated SiQD-NPs had exceptional biocompatibility, with minimal cytotoxicity at concentration up to 1600 µg mL(-1). Under 365 nm excitation, the SiQD-NP colloid emits bright reddish photoluminescence with PLQY = 45-55% in organic solvent and 5-10% in aqueous buffer. Finally, through confocal fluorescent imaging and flow cytometry analysis, the anti-HER2 conjugated SiQD-NPs show obvious specific binding to the HER2-overexpressing SKOV3 cells and negligible nonspecific binding to the HER2-nonexpressing CHO cells. Under similar experimental conditions, the immunofluorescence results obtained with the SiQD-NPs are comparable to those using conventional fluorescein isothiocyanate (FITC).

Photonic Crystal Optical Tweezers with High Efficiency for Live Biological Samples and Viability Characterization.

We propose and demonstrate a new optical trapping method for single cells that utilizes modulated light fields to trap a wide array of cell types, including mammalian, yeast, and Escherichia coli cells, on the surface of a two-dimensional photonic crystal. This method is capable of reducing the required light intensity, and thus minimizing the photothermal damage to living cells, thereby extending cell viability in optical trapping and cell manipulation applications. To this end, a thorough characterization of cell viability in optical trapping environments was performed. This study also demonstrates the technique using spatial light modulation in patterned manipulation of live cell arrays over a broad area.

MEMS scanning micromirror for optical coherence tomography.

This paper describes an endoscopic-inspired imaging system employing a micro-electromechanical system (MEMS) micromirror scanner to achieve beam scanning for optical coherence tomography (OCT) imaging. Miniaturization of a scanning mirror using MEMS technology can allow a fully functional imaging probe to be contained in a package sufficiently small for utilization in a working channel of a standard gastroesophageal endoscope. This work employs advanced image processing techniques to enhance the images acquired using the MEMS scanner to correct non-idealities in mirror performance. The experimental results demonstrate the effectiveness of the proposed technique.

Red-emitting silicon quantum dot phosphors in warm white LEDs with excellent color rendering.

We demonstrate red-emitting silicon quantum dot (SiQD) phosphors as a low-cost and environment-friendly alternative to rare-earth element phosphors or CdSe quantum dots. After surface passivation, the SiQD-phosphors achieve high photoluminescence quantum yield = 51% with 365-nm excitation. The phosphors also have a peak photoluminescence wavelength at 630 nm and a full-width-at-half-maximum of 145 nm. The relatively broadband red emission is ideal for forming the basis of a warm white spectrum. With 365-nm or 405-nm LED pumping and the addition of green- and/or blue-emitting rare-earth element phosphors, warm white LEDs with color rendering index ~95 have been achieved.

Red-emitting silicon quantum dot phosphors in warm white LEDs with excellent color rendering.

We demonstrate red-emitting silicon quantum dot (SiQD) phosphors as a low-cost and environment-friendly alternative to rare-earth element phosphors or CdSe quantum dots. After surface passivation, the SiQD-phosphors achieve high photoluminescence quantum yield = 51% with 365-nm excitation. The phosphors also have a peak photoluminescence wavelength at 630 nm and a full-width-at-half-maximum of 145 nm. The relatively broadband red emission is ideal for forming the basis of a warm white spectrum. With 365-nm or 405-nm LED pumping and the addition of green- and/or blue-emitting rare-earth element phosphors, warm white LEDs with color rendering index ~95 have been achieved.

Diffractive catheter for ultrahigh-resolution spectral-domain volumetric OCT imaging.

We present a novel design for an endoscopic imaging catheter utilizing diffractive optics for ultrahigh-resolution optical coherence tomography (OCT) imaging at 800 nm. A diffractive microlens was developed to alleviate severe chromatic aberration when a broadband light source was employed at the 800 nm wavelength range. Combined with a home-built fiber rotary joint and a broadband Ti:sapphire laser, the imaging catheter achieved a lateral resolution of 6.2 µm and an axial resolution of 3.0 µm in air. The performance of the catheter was demonstrated by three-dimensional full-circumferential endoscopic OCT imaging of guinea pig esophagus in vivo.

Fluorescent porous silicon biological probes with high quantum efficiency and stability.

We demonstrate porous silicon biological probes as a stable and non-toxic alternative to organic dyes or cadmium-containing quantum dots for imaging and sensing applications. The fluorescent silicon quantum dots which are embedded on the porous silicon surface are passivated with carboxyl-terminated ligands through stable Si-C covalent bonds. The porous silicon bio-probes have shown photoluminescence quantum yield around 50% under near-UV excitation, with high photochemical and thermal stability. The bio-probes can be efficiently conjugated with antibodies, which is confirmed by a standard enzyme-linked immunosorbent assay (ELISA) method.

Dynamic focus-tracking MEMS scanning micromirror with low actuation voltages for endoscopic imaging.

We demonstrate a 3-D scanning micromirror device that combines 2-D beam scanning with focus control in the same device using micro-electro-mechanical-systems (MEMS) technology. 2-D beam scanning is achieved with a biaxial gimbal structure and focus control is obtained with a deformable mirror membrane surface. The micromirror with 800 micrometer diameter is designed to be sufficiently compact and efficient so that it can be incorporated into an endoscopic imaging probe in the future. The design, fabrication and characterization of the device are described in this paper. Using the focus-tracking MEMS scanning mirror, we achieved an optical scanning range of >16 degrees with <40 V actuation voltage at resonance and a tunable focal length between infinity and 25 mm with <100V applied bias.

Synthesis and characterization of anti-EGFR fluorescent nanoparticles for optical molecular imaging.

Molecular imaging, the visualization of molecular and cellular markers, is a promising method for detection of dysplasia and early cancer in the esophagus and can potentially be used to identify regions of interest for biopsy or tumor margins for resection. EGFR is a previously reported cell surface receptor with stepwise increases in expression during the progression from Barrett's metaplasia to adenocarcinoma. In this work, a 200 nm fluorescent nanoparticle contrast agent was synthesized for targeted imaging of EGFR through a series of surface modifications to dye-encapsulated polystyrene particles. Amino-functionalized polystyrene particles were PEGylated using a heterobifunctional PEG linker. Subsequently, thiolated M225 antibodies were conjugated to maleimide functional groups on attached PEGs for EGFR targeting. In vitro binding studies using flow cytometry demonstrated specific binding of M225-PEG-NP to EGFR-expressing cells with minimal nonspecific binding in EGFR(-) cells. Binding was shown to increase proportionally with the number of conjugated M225 antibodies. Adsorbed formulations with unmodified M225 antibodies, M225 + PEG-NP, were synthesized using the same antibody feeds used in M225-PEG-NP synthesis to determine the contribution of adsorbed antibodies to EGFR targeting. Adsorbed antibodies were less efficient at mediated nanoparticle targeting to EGFR than conjugated antibodies. Finally, M225-PEG-NP demonstrated binding to EGFR-expressing regions in human esophageal tissue sections.