Hydrogen production from formic acid solution by modified TiO2 and titanate nanotubes in a two-step system under visible light irradiation.

Hydrogen gas is one of the most promising renewable energy sources, and the final product of hydrogen combustion is nothing but water. However, it is still a big challenge to produce hydrogen and store it. Many studies have been conducted into produce hydrogen from water using photocatalysts. Z-scheme photocatalysis is a two-photocatalyst system that comprises a hydrogen catalyst and an oxygen catalyst to produce hydrogen and oxygen respectively. Compared to the one-step system, the two-step system can promote the efficiency of water splitting. In addition, formic acid (FA) is a convenient hydrogen-storage material and can be safely handled in aqueous solutions. Therefore, this study investigated the photocatalytic conversion of FA solution to hydrogen using visible light with several types of hydrogen catalysts (CdS/titanate nanotubes (TNTs), CdS/TiO2, Pt/CdS/TNTs) and WO3 as the oxygen catalyst. The results showed that the yield of hydrogen with CdS/TNTs + WO3 was much higher than with CdS/TiO2 + WO3. Moreover, coating the photocatalysts with metal could further promote the reaction. The optimal platinum loading was 0.01 wt%, and the hydrogen production achieved was 852.5 µmol · h(-1) with 20 vol% FA solution.

Microwave torrefaction of rice straw and Pennisetum.

Microwave torrefaction of rice straw and pennisetum was researched in this article. Higher microwave power levels contributed to higher heating rate and reaction temperature, and thus produced the torrefied biomass with higher heating value and lower H/C and O/C ratios. Kinetic parameters were determined with good coefficients of determination, so the microwave torrefaction of biomass might be very close to first-order reaction. Only 150W microwave power levels and 10min processing time were needed to meet about 70% mass yield and 80% energy yield for torrefied biomass. The energy density of torrefied biomass was about 14% higher than that of raw biomass. The byproducts (liquid and gas) possessed about 30% mass and 20% energy of raw biomass, and they can be seen as energy sources for heat or electricity. Microwave torrefaction of biomass could be a competitive technology to employ the least energy and to retain the most bioenergy.

A sequential method to analyze the kinetics of biomass pyrolysis.

The kinetics of biomass pyrolysis was studied via a sequential method including two stages. Stage one is to analyze the kinetics of biomass pyrolysis and starts with the determination of unreacted fraction of sample at the maximum reaction rate, (1-α)(m). Stage two provides a way to simulate the reaction rate profile and to verify the appropriateness of kinetic parameters calculated in the previous stage. Filter paper, xylan, and alkali lignin were used as representatives of cellulose, hemicellulose, and lignin whose pyrolysis was analyzed with the assumption of the orders of reaction being 1, 2, and 3, respectively. For most of the biomass pyrolysis, kinetic parameters were properly determined and reaction rate profiles were adequately simulated by regarding the order of reaction as 1. This new method should be applicable to most of the biomass pyrolysis and similar reactions whose (1-α)(m) is acquirable, representative, and reliable.

Photocatalytic oxidation of ammonia by cadmium sulfide/titanate nanotubes synthesised by microwave hydrothermal method.

CdS/Titanate nanotubes (TNTs) were successfully synthesised by a simple, rapid, and reliable microwave hydrothermal method. The CdS nanoparticles synthesised using a 140-W microwave irradiation power at 423 K photodegraded 26% ammonia in water, while the photocatalytic efficiency increased to 52.3% using the synthesised CdS/TNTs composites. The results indicated that the CdS/TNTs photocatalysts possess improved photocatalytic activity than that of CdS or TNTs materials alone.

Pyrolysis of biomass by thermal analysis-mass spectrometry (TA-MS).

The kinetic parameters such as pre-exponential factor and activation energy of hemicellulose, cellulose, and lignin were well determined by the linear regressions of selected, sufficient thermogravimetric data, and close to literature values. The pyrolysis of biomass can be divided into four stages. There was only drying in the zeroth stage (<150°C). In the first stage (150-250°C), some light hydrocarbons were produced with the early pyrolysis of biomass. The biomass was mainly pyrolyzed in the second stage (250-500°C) with higher reaction rates than those of other stages. The productions of H(2) and CO(2) in the third stage (>500°C) may be able to be the evidence of self-gasification of char existing at higher temperatures.

Hydrogen-rich fuel gas from rice straw via microwave-induced pyrolysis.

This study aimed to research the productivity of H(2)-rich fuel gas from rice straw using the microwave-induced pyrolysis. The formation constituents of gas product and the mechanism of its production were also discussed. The primary components of gas product were H(2), CO(2), CO, and CH(4), with average percentages of 50.67, 22.56, 16.09, and 7.42vol.%, respectively. According to the TA-MS analysis, it was suggested that focused heating by microwaves made the microwave-induced pyrolysis different from the traditional pyrolysis. A chemical equation could be nearly balanced to illustrate the gas composition generated from rice straw. From the viewpoint of energy consumption, close to 60% of the input energy could be derived and utilized as bioenergy.

Recovery of heavy metals from industrial sludge using various acid extraction approaches.

Heavy metals were removed from industrial sludge by traditional and microwave-assisted acid extraction approaches. The effects of acid concentration, extraction time, sludge particle size and solid/liquid (S/L) ratio on copper-extraction efficiency were assessed. Leaching with increased acid concentrations increased the yield of heavy metals from the industrial sludge. In microwave-assisted acid extraction, reducing the S/L ratio and sludge particle size increased copper-extraction efficiency. These experimental findings indicate that S/L ratio most strongly influenced microwave-assisted acid extraction. Both traditional and microwave-assisted acid extraction demonstrate that sulfuric acid was an effective extractant, and the copper fraction in extracted sludge shifted from being primarily bound to Fe-Mn oxides and organic-matter partition, to being mostly bound to organic matter, remaining as a residue during acid extraction.

Optimal strategies for best management practice placement in a synthetic watershed.

It is significant to arrange suitable design and placement of best management practices (BMPs) for reaching the aim that can not only satisfy environmental quality standards, but also decrease the total cost of BMPs. This study applied WinVAST model to predict watershed responses. The objective of this work was to discuss both the economic costs and benefits of BMPs and the control efficiency of discharge and pollutant exports, and to create some suitable standards for the optimal BMPs placement strategies. It is significant to find an optimal number and location of BMPs. In the case study herein, the number of BMPs including a detention pond and a grassy swale would be better to be given by four. The number of BMPs should also be determined by the environmental standards. Moreover, the result shows that the optimal location of BMPs placement is in the downstream area near the outlet and on the mainstream of the catchment. When the BMPs are set in these regions, it cannot only reduce the peak flow and peak pollutant exports, but also have slow time to peak watershed responses.

Cyclosporine, an immunosuppressant, attenuates phorbol-induced lung injury in rats.

OBJECTIVE: White cell activation in the lung plays a critical role to induce lung injury and lymphocytes in the thoracic duct system may also participate. We evaluated the effect of cyclosporine on phorbol myristate acetate (PMA)-induced lung injury. MATERIALS AND METHODS: We used an in situ isolated, blood perfused rat lung model to measure pulmonary arterial pressure (PAP) and lung weight gain (LWG; g) for 50 minutes after a bolus injection of PMA (0.05 microg/mL). Oxygen radical release was estimated by an LKB 1251 luminometer and by nitric oxide (NO) release as measured by an ENO-20 NO analyzer. RESULTS: In the group exposed to PMA alone, the mean PAP increased from 16.53 +/- 1.28 to 43.33 +/- 3.40 mm Hg (P < .001), and lung weight increased by 4.35 +/- 0.67 g during the 50-minute perfusion after PMA challenge (P < .001). In vitro measurement showed that PMA induced a significant increase in oxygen radical release (P < .001). PMA attenuated NO release (P < .001) into the perfusion system. Pretreatment with cyclosporine (3 mg/kg) for 3 days prevented the increases in both PAP (P < .01) and LWG (P < .001). NO release was maintained in cyclosporine-pretreated rats. Cyclosporine also showed dose-dependent attenuation of oxygen radical release by PMA-activated white blood cells. CONCLUSION: The mechanisms responsible for the protective effect of cyclosporine on the lung injury induced by phorbol may be related to an attenuation of oxygen radical production with maintenance of NO release.

Total recovery of resources and energy from rice straw using microwave-induced pyrolysis.

This article presents the application of microwave-induced pyrolysis to total recovery of resources and energy from rice straw. The microwave power and particle size of feedstock were both key parameters affecting the performance of microwave-induced pyrolysis. Under 400-500W microwave power, the reduction of fixed carbon in the biomass was significant. From the experimental results of specific surface area, zeta potential, and Cu2+ adsorption, the applications of solid residues in the water and wastewater treatment could be expected. The major compositions in gaseous product were H2, CO2, CO, CH4 of 55, 17, 13, 10vol.%, respectively. The high H2 content might imply that microwave-induced pyrolysis of biomass waste has the potential to produce the H2-rich fuel gas. Alkanes, polars, and low-ringed polycyclic aromatic hydrocarbons were three primary kinds of compounds in the liquid product.

Effect of spatial variability of storm on the optimal placement of best management practices (BMPs).

It is significant to design best management practices (BMPs) and determine the proper BMPs placement for the purpose that can not only satisfy the water quantity and water quality standard, but also lower the total cost of BMPs. The spatial rainfall variability can have much effect on its relative runoff and non-point source pollution (NPSP). Meantime, the optimal design and placement of BMPs would be different as well. The objective of this study was to discuss the relationship between the spatial variability of rainfall and the optimal BMPs placements. Three synthetic rainfall storms with varied spatial distributions, including uniform rainfall, downstream rainfall and upstream rainfall, were designed. WinVAST model was applied to predict runoff and NPSP. Additionally, detention pond and swale were selected for being structural BMPs. Scatter search was applied to find the optimal BMPs placement. The results show that mostly the total cost of BMPs is higher in downstream rainfall than in upstream rainfall or uniform rainfall. Moreover, the cost of detention pond is much higher than swale. Thus, even though detention pond has larger efficiency for lowering peak flow and pollutant exports, it is not always the determined set in each subbasin.

Evaluation of atmospheric deposition of nitrogen to the Feitsui reservoir in Taipei.

This research studied how the air pollutants of urban areas affect a neighboring reservoir and its water quality. Through the atmospheric dispersion process, air pollutants move from the Taipei metropolitan to the Feitsui reservoir and enter the water body through dry and wet depositions. ISCST3 (Industrial Source Complex Short Term Model), an air quality model, was used to simulate dispersion, dry deposition and wet deposition of the air pollutants. Then the nitrogen loadings to the Feitsui Reservoir were evaluated. The results indicate that wet deposition places a greater burden than dry deposition does on the water body. Wet and dry deposition of NH4+ together make up a rather large proportion of the total pollution. The ranged from 21.9 to 25.2%. Those of nitrate make up a smaller proportion, ranged from 2.0 to 2.3%. If we take indirect deposition into account and calculate the NO3- and NH4+ together, the proportion is 15.9-17.6%.

Balancing infection control practices and family-centred care in a cohort of paediatric suspected severe acute respiratory syndrome patients in Hong Kong.

OBJECTIVE: To identify key nursing issues for paediatric patients suspected of severe acute respiratory syndrome (SARS) in relation to the family-centred model of nursing care and to develop a data-based model of paediatric nursing care to be better applied in situations of suspected SARS or where outbreaks of other infectious diseases occur. METHODS: This is a retrospective descriptive case series, which analysed the medical and nursing records of all highly-suspected/suspected SARS patients admitted to a major acute hospital in Hong Kong. Key nursing personnel were also interviewed. RESULTS: The study included a total of 17 highly-suspected and 49 suspected SARS paediatric patients (age: 1-16). None of the paediatric patients was eventually diagnosed of SARS. Most cases presented fever (highly-suspected: 76.5%/ suspected: 100%), cough (64.7%/71.4%), nausea and vomiting (35.3%/28.6%). Nursing care was provided to the patients as necessary. Both the children and parents experienced fear of SARS, as well as separation anxiety arisen from hospitalization in a strict isolation setting. CONCLUSIONS: Infection control overshadowed the family-centred nursing practices in the management of SARS paediatric patients. A major nursing care issue for SARS paediatric patients was to achieve a careful balance between attending to patients' physical and psychological needs and adhering to the infection control guidelines, while at the same time offering psychological support to family members. The current philosophy and practice of family-centred nursing model neglect the special needs of children with infectious diseases and predominantly apply to children with non-infectious diseases that family visits are allowed and nursing care by parents are encouraged.

Raising and controlling study of dissolved oxygen concentration in closed-type aeration tank.

This study investigated the promotion and control of dissolved oxygen (DO) concentration of the closed-type aeration tank via practical experiments in the wastewater treatment system of a 5-star hotel in Taipei. As with limited and treasured space in Taiwan, before the completion of the sewer system construction in cities, to utilize the mat foundation under large buildings as the space of sewage treatment plant still has been one of the alternatives of those sewage treatments. However, aeration tanks constructed in the mat foundation of buildings have smaller effective water depth, which will cause a lower total transfer amount of DO. Controlling the total exhaust gas flow rate can increase the pressure on such closed-type aeration tanks. The DO concentration thus may increase according to Henry's Law. Furthermore, it may enable operators to adjust the DO concentration of the aeration tank more precisely and thus sustain optimal operating conditions in these treatment facilities. Practical experiments indicated that the DO concentration of aeration tank maintains an average of 3.8 mg l(-1), obtaining the optimum operating conditions. The efficiency of the biological treatment facilities in the mat foundation could be markedly improved.

Treating chemical mechanical polishing (CMP) wastewater by electro-coagulation-flotation process with surfactant.

The effect of surfactants on the treatment of chemical mechanical polishing (CMP) wastewater by electro-coagulation-flotation (ECF) process was studied. Two surfactants, cetyltrimethylammonium bromide (CTAB) and sodium dodecylsulfate (SDS) were employed in this study to compare the effect of cationic (CTAB) and anodic (SDS) surfactants on ECF. The cationic surfactant can enhance the removal of the turbidity, but anodic surfactant cannot. It can be explained by the hetero-coagulation theory. Moreover, the addition of CTAB in CMP wastewater can reduce the sludge volume and the flotation/sedimentation time in ECF process. The residual turbidity and dissolved silicon dropped with the increase of charge loading. No CTAB pollution problem exists after the ECF process.

Removal of fluoride from semiconductor wastewater by electrocoagulation-flotation.

This work employs an anodic surfactant, sodium dodecyl sulfate (SDS), to improve the flotation performance of the electrocoagulation-flotation (ECF) process to treated fluoride containing semiconductor wastewater following calcium precipitation. The dissolved fluoride ions and CaF(2) particles in the wastewater after calcium precipitation were effectively removed in the ECF process simultaneously. The dosage of SDS required for ECF was much less than those for dispersed air flotation (DiAF) or dissolved air flotation (DAF) processes because the CaF(2) particles can be collected by hydro-fluoro-aluminum flocs in ECF. Thus, SDS only served as a frother to make the bubbles tiny and stable in the ECF defluoridation process. The interference of co-existing anions can be overcome by increasing the dosage of calcium ions and SDS. The optimum initial acidity for ECF is close to the initial fluoride concentration after calcium precipitation; the amount of SS removed dropped rapidly if the initial acidity exceeded the optimal value because the surface charge of the hydro-fluoro-aluminum particles increased. The initial acidity of the wastewater after calcium precipitation can be modified by changing the [Ca(OH)(2)]/[Ca(2+)](T) ratio and the appropriate ratio is approximately given by the acid dissociation constant of hydrofluoric acid and the initial pH of the wastewater before calcium precipitation.

Effects of the molar ratio of hydroxide and fluoride to Al(III) on fluoride removal by coagulation and electrocoagulation.

The effect of the molar ratio of hydroxide and fluoride ions to Al(III) ions (gamma(OH) and gamma(F)) on coagulation and electrocoagulation (EC) was studied to solve the problem of the over addition of acid or base. The efficiency of defluoridation was approximately 100% when the sum of gamma(OH) and gamma(F) (gamma(OH+F)) was close to 3. This finding reveals that the fluoride ions and the hydroxide ions can co-precipitate with Al(III) ions and the formula of the precipitate is Al(n)F(m)(OH)(3n-m). However, when gamma(OH) was less than 2.4, the defluoridation efficiency, given that gamma(OH+F)=3, dropped as gamma(OH) fell, because the amount of aluminum polymer formed dropped. The efficiency of defluoridation of EC exceeded that of coagulation for equal gamma(OH) and gamma(OH+F), when gamma(OH+F)>3, proving the existence of an electrocondensation effect.

Methods for accelerating nitrate reduction using zerovalent iron at near-neutral pH: effects of H2-reducing pretreatment and copper deposition.

Both surface treatments, H2-reducing pretreatment at 400 degrees C and the deposition of copper as a catalyst, were attempted to enhance the removal of nitrate (40 (mg N) L(-1)) using zerovalent iron in a HEPES buffered solution at a pH of between 6.5 and 7.5. After the iron surface was pretreated with hydrogen gas, the removal of the passive oxide layers that covered the iron was indicated by the decline in the oxygen fraction (energy dispersive X-ray analysis) and the overlap of the cyclic polarization curves. The reaction rate was doubled, and the lag of the early period disappeared. Then, the deposition of copper onto freshly pretreated iron promoted nitrate degradation more effectively than that onto a nonpretreated iron surface, because of the high dispersion and small size of the copper particles. An optimum of 0.25-0.5% (w/w) Cu/Fe accelerated the rate by more than six times that of the nonpretreated iron. The aged 0.5% (w/w) Cu/Fe with continual dipping in nitrate solution for 20 days completely restored its reactivity by a regeneration process with H2 reduction. Hence, these two iron surface treatments considerably promoted the removal of nitrate from near-neutral water; the reactivity of Cu/Fe was effectively recovered.

Effects of co-existing anions on fluoride removal in electrocoagulation (EC) process using aluminum electrodes.

Batch experiments with bipolar aluminum electrodes and potentiodynamic polarization tests with monopolar systems were conducted to investigate the effects of the type and concentration of co-existing anions on defluoridation in electrocoagulation (EC) process. The results demonstrate that the type of the dominant anion directs the EC defluoridation reaction. The defluoridation efficiency was almost 100% and most of the fluoride removal reaction occurred on the surface of the anode in the solution without the co-existing anions, due to the electro-condensation effect. In the solutions with co-existing anions, most of the defluoridation took place in bulk solution. The residual fluoride concentration is a function of the total mass of Al(III) liberation from anodes and the types of the functions in the solutions with and without co-existing anions are different. The existence of sulfate ions inhibits the localized corrosion of aluminum electrodes, leading to lower defluoridation efficiency because of lower current efficiency. The presence of chloride or nitrate ions prevented the inhibition of sulfate ions, and the chloride ions were more efficient. Different corrosion types occurred in different anion-containing solutions and the form of corrosion affected the kinetic over-potential. The bypass flow causes the decrease of current efficiency and the proportion of the bypass flow of current increased due to a rise of the kinetic over potential and the conductivity of the solution.

Treatment of slaughterhouse wastewater using an activated sludge/contact aeration process.

This study combines a two-phase biological treatment system of activated sludge/contact aeration process by adding biological contact filters into the rear sector of the activated sludge aeration tank of the slaughterhouse wastewater treatment plant. This system keeps the advantages of complete mixing of substrates and microorganisms and flexible operation of the activated sludge process, and increased biological phase, less sludge, process stability and good settleability of sludge of the contact aeration process. This system could avoid the defects of sludge bulking, increased sludge production and difficult operation of the activated sludge process, and system clogging and rigid operation of the contact aeration process. Because suspended microorganisms are flowing into the contact aeration system, which then degrade or suspend within the biological contact filters after being adsorbed by the fixed biological film, on which partial bio-solids will act as seeding microorganisms. Suspended microorganisms and the dropped biological film will settled in the secondary settling tank, then reflux into the activated sludge aeration tank. The partial dropped biological film will decompose in the activated sludge aeration tank to achieve the function of decreasing sludge. Large specific gravity and good settling ability of biofilm sludge will provide better effluent quality. It has been proven through a practical experiment at a slaughterhouse wastewater treatment plant in Taiwan, that the activated sludge process effluent COD value of 150-200 mg/L and SS value of 80-100 mg/L were decreased to around 40 mg/L and 22 mg/L, respectively, after changing its system to the two-phase biological treatment system of activated sludge/contact aeration process.