Reducing nonradiative recombination for highly efficient inverted perovskite solar cells via a synergistic bimolecular interface.

Reducing interface nonradiative recombination is important for realizing highly efficient perovskite solar cells. In this work, we develop a synergistic bimolecular interlayer (SBI) strategy via 4-methoxyphenylphosphonic acid (MPA) and 2-phenylethylammonium iodide (PEAI) to functionalize the perovskite interface. MPA induces an in-situ chemical reaction at the perovskite surface via forming strong P-O-Pb covalent bonds that diminish the surface defect density and upshift the surface Fermi level. PEAI further creates an additional negative surface dipole so that a more n-type perovskite surface is constructed, which enhances electron extraction at the top interface. With this cooperative surface treatment, we greatly minimize interface nonradiative recombination through both enhanced defect passivation and improved energetics. The resulting p-i-n device achieves a stabilized power conversion efficiency of 25.53% and one of the smallest nonradiative recombination induced Voc loss of only 59 mV reported to date. We also obtain a certified efficiency of 25.05%. This work sheds light on the synergistic interface engineering for further improvement of perovskite solar cells.

On the role of asymmetric molecular geometry in high-performance organic solar cells.

Although asymmetric molecular design has been widely demonstrated effective for organic photovoltaics (OPVs), the correlation between asymmetric molecular geometry and their optoelectronic properties is still unclear. To access this issue, we have designed and synthesized several symmetric-asymmetric non-fullerene acceptors (NFAs) pairs with identical physical and optoelectronic properties. Interestingly, we found that the asymmetric NFAs universally exhibited increased open-circuit voltage compared to their symmetric counterparts, due to the reduced non-radiative charge recombination. From our molecular-dynamic simulations, the asymmetric NFA naturally exhibits more diverse molecular interaction patterns at the donor (D):acceptor (A) interface as compared to the symmetric ones, as well as higher D:A interfacial charge-transfer state energy. Moreover, it is observed that the asymmetric structure can effectively suppress triplet state formation. These advantages enable a best efficiency of 18.80%, which is one of the champion results among binary OPVs. Therefore, this work unambiguously demonstrates the unique advantage of asymmetric molecular geometry, unveils the underlying mechanism, and highlights the manipulation of D:A interface as an important consideration for future molecular design.

A 3,3'-Difluoro-2,2'-Bithiophene Based Donor Polymer Realizing High Efficiency (>17%) Single Junction Binary Organic Solar Cells.

In this study, two novel donor-acceptor (D-A) copolymers are designed and synthesized, DTBT-2T and DTBT-2T2F with 2,2'-bithiophene or 3,3'-difluoro-2,2'-bithiophene as the donor unit and dithienobenzothiadiazole as the acceptor unit, and used them as donor materials in non-fullerene organic solar cells (OSCs). Due to enhanced planarity of polymer chains resulted by the intramolecular F···S noncovalent interactions, the incorporation of 3,3'-difluoro-2,2'-bithiophene unit instead of 2,2'-bithiophene into the polymers can enhance their molecular packing, crystallinity and hole mobility. The DTBT-2T:L8-BO based binary OSCs deliver a power conversion efficiency (PCE) of only 9.71% with a Voc of 0.78 V, a Jsc of 20.69 mA cm-2 , and an FF of 59.67%. Moreover, the introduction of fluoro atoms can lower the highest occupied molecular orbital levels. As a result, DTBT-2T2F:L8-BO based single-junction binary OSCs exhibited less recombination loss, more balanced charge mobility, and more favorable morphology, resulting in an impressive PCE of 17.03% with a higher Voc of 0.89 V, a Jsc of 25.40 mA cm-2, and an FF of 75.74%. These results indicate that 3,3'-difluoro-2,2'-bithiophene unit can be used as an effective building block to synthesize high performance polymer donor materials. This work greatly expands the selection range of donor units for constructing high-performance polymers.

Decreasing exciton dissociation rates for reduced voltage losses in organic solar cells.

Enhancing the device electroluminescence quantum efficiency (EQEEL) is a critical factor in mitigating non-radiative voltage losses (VNR) and further improving the performance of organic solar cells (OSCs). While the common understanding attributes EQEEL in OSCs to the dynamics of charge transfer (CT) states, persistent efforts to manipulate these decay dynamics have yielded limited results, with the EQEEL of high-efficiency OSCs typically remaining below 10-2%. This value is considerably lower than that observed in high efficiency inorganic photovoltaic devices. Here, we report that EQEEL is also influenced by the dissociation rate constant of singlet states (kDS). Importantly, in contrast to the traditional belief that advocates maximizing kDS for superior photovoltaic quantum efficiency (EQEPV), a controlled reduction in kDS is shown to enhance EQEEL without compromising EQEPV. Consequently, a promising experimental approach to address the VNR challenge is proposed, resulting in a significant improvement in the performance of OSCs.

Delayed Crystallization Kinetics Allowing High-Efficiency All-Polymer Photovoltaics with Superior Upscaled Manufacturing.

Though encouraging performance is achieved in small-area organic photovoltaics (OPVs), reducing efficiency loss when evoluted to large-area modules is an important but unsolved issue. Considering that polymer materials show benefits in film-forming processability and mechanical robustness, a high-efficiency all-polymer OPV module is demonstrated in this work. First, a ternary blend consisting of two polymer donors, PM6 and PBQx-TCl, and one polymer acceptor, PY-IT, is developed, with which triplet state recombination is suppressed for a reduced energy loss, thus allowing a higher voltage; and donor-acceptor miscibility is compromised for enhanced charge transport, thus resulting in improved photocurrent and fill factor; all these contribute to a champion efficiency of 19% for all-polymer OPVs. Second, the delayed crystallization kinetics from solution to film solidification is achieved that gives a longer operation time window for optimized blend morphology in large-area module, thus relieving the loss of fill factor and allowing a record efficiency of 16.26% on an upscaled module with an area of 19.3 cm2 . Besides, this all-polymer system also shows excellent mechanical stability. This work demonstrates that all-polymer ternary systems are capable of solving the upscaled manufacturing issue, thereby enabling high-efficiency OPV modules.

Passivating Dipole Layer Bridged 3D/2D Perovskite Heterojunction for Highly Efficient and Stable p-i-n Solar Cells.

Constructing 3D/2D perovskite heterojunction is a promising approach to integrate the benefits of high efficiency and superior stability in perovskite solar cells (PSCs). However, in contrast to n-i-p architectural PSCs, the p-i-n PSCs with 3D/2D heterojunction have serious limitations in achieving high-performance as they suffer from a large energetic mismatch and electron extraction energy barrier from a 3D perovskite layer to a 2D perovskite layer, and serious nonradiative recombination at the heterojunction. Here a strategy of incorporating a thin passivating dipole layer (PDL) onto 3D perovskite and then depositing 2D perovskite without dissolving the underlying layer to form an efficient 3D/PDL/2D heterojunction is developed. It is revealed that PDL regulates the energy level alignment with the appearance of interfacial dipole and strongly interacts with 3D perovskite through covalent bonds, which eliminate the energetic mismatch, reduce the surface defects, suppress the nonradiative recombination, and thus accelerate the charge extraction at such electron-selective contact. As a result, it is reported that the 3D/PDL/2D junction p-i-n PSCs present a power conversion efficiency of 24.85% with robust stability, which is comparable to the state-of-the-art efficiency of the 3D/2D junction n-i-p devices.

Macrocyclic Encapsulation in a Non-fused Tetrathiophene Acceptor for Efficient Organic Solar Cells with High Short-Circuit Current Density.

Non-fullerene acceptors have shown great promise for organic solar cells (OSCs). However, challenges in achieving high efficiency molecular system with conformational unicity and effective molecular stacking remain. In this study, we present a new design of non-fused tetrathiophene acceptor R4T-1 via employing the encapsulation of tetrathiophene with macrocyclic ring. The single crystal structure analysis reveals that cyclic alkyl side chains can perfectly encapsulate the central part of molecule and generate a conformational stable and planar molecular backbone. Whereas, the control 4T-5 without the encapsulation restriction displays cis- and twisted conformation. As a result, R4T-1 based OSCs achieved an outstanding power conversion efficiency (PCE) exceeding 15.10 % with a high short-circuit current density (Jsc ) of 25.48 mA/cm2 , which is significantly improved by ≈30 % in relative to that of the control. Our findings demonstrate that the macrocyclic encapsulation strategy could assist fully non-fused electron acceptors (FNEAs) to achieve a high photovoltaic performance and pave a new way for FNEAs design.

High-Pressure Fabrication of Binary Organic Solar Cells with High Molecular Weight D18 Yields Record 19.65 % Efficiency.

In this work, inspired by the principles of a pressure cooker, we utilized a high-pressure method to address the processing challenges associated with high molecular weight polymers. Through this approach, we successfully dissolved high molecular weight D18 in chloroform at 100 °C within a pressure-tight vial. The increased steam pressure raised the boiling point and dissolving capacity of chloroform, enabling the creation of a hybrid film with superior properties, including more ordered molecular arrangement, increased crystallinity, extended exciton diffusion length, and improved phase morphology. Organic solar cells (OSCs) based on D18 : L8-BO prepared using this high-pressure method achieved an outstanding power conversion efficiency of 19.65 %, setting a new record for binary devices to date. Furthermore, this high-pressure method was successfully applied to fabricate OSCs based on other common systems, leading to significant enhancements in device performance. In summary, this research introduces a universal method for processing high molecular weight D18 materials, ultimately resulting in the highest performance reported for binary organic solar cells.

A rare case of brominated small molecule acceptors for high-efficiency organic solar cells.

Given that bromine possesses similar properties but extra merits of easily synthesizing and polarizing comparing to homomorphic fluorine and chlorine, it is quite surprising very rare high-performance brominated small molecule acceptors have been reported. This may be caused by undesirable film morphologies stemming from relatively larger steric hindrance and excessive crystallinity of bromides. To maximize the advantages of bromides while circumventing weaknesses, three acceptors (CH20, CH21 and CH22) are constructed with stepwise brominating on central units rather than conventional end groups, thus enhancing intermolecular packing, crystallinity and dielectric constant of them without damaging the favorable intermolecular packing through end groups. Consequently, PM6:CH22-based binary organic solar cells render the highest efficiency of 19.06% for brominated acceptors, more excitingly, a record-breaking efficiency of 15.70% when further thickening active layers to ~500 nm. By exhibiting such a rare high-performance brominated acceptor, our work highlights the great potential for achieving record-breaking organic solar cells through delicately brominating.

Solution-Processed ZnO with Conductivity over 1000 S cm-1 for ITO-Free Organic Photovoltaics.

Developing transparent conductors to replace indium tin oxide (ITO) is a critical objective in the field of organic optoelectronics. Non-atomically doped (NAD) ZnO thin films, while currently exhibiting limited conductivity, are highly promising candidates due to their unique advantages, such as having complete transparency in both the visible and near-infrared spectral regions, solution processability, and the desired surface electronic properties. In this work, the impact of surface modification by insulating polymers on the ultraviolet-enhanced conductivity of NAD-ZnO films is investigated. It was found that polymer modifiers that are rich in amino and hydroxyl groups are effective at increasing the concentration of oxygen vacancies and the conductivity of NAD-ZnO films. The highest conductivity of over 1000 S cm-1, which is more than twice as high as the previous record for NAD-ZnO films, is achieved using polyethylenimine ethoxylated (PEIE) to modify NAD-ZnO films. Subsequently, the replacement of ITO in organic photovoltaic devices by a ZnO/PEIE electrode is realized. The ZnO/PEIE-based OPV devices that were created exhibit performances comparable to those of ITO-based devices under simulated solar illumination and performances better than those achieved with ITO-based devices under simulated indoor illumination. These results make NAD-ZnO a promising candidate for the widespread replacement of ITO in optoelectronic devices.

An Isomeric Solid Additive Enables High-Efficiency Polymer Solar Cells Developed Using a Benzo-Difuran-Based Donor Polymer.

Currently, nearly all high-efficiency organic photovoltaic devices use donor polymers based on the benzo-dithiophene (BDT) unit. To diversify the choices of building blocks for high-performance donor polymers, the use of benzo-difuran (BDF) units is explored, which can achieve reduced steric hindrance, stronger molecular packing, and tunable energy levels. In previous research, the performance of BDF-based devices lagged behind those of BDT-based devices. In this study, a high efficiency (18.4%) is achieved using a BDF-based polymer donor, which is the highest efficiency reported for BDF donor materials to date. The high efficiency is enabled by a donor polymer (D18-Fu) and the aid of a solid additive (2-chloronaphthalene), which is the isomer of the commonly used additive 1-chloronaphthalene. These results revealed the significant effect of 2-chloronaphthalene in optimizing the morphology and enhancing the device parameters. This work not only provides a new building block that can achieve an efficiency comparable to dominant BDT units but also proposes a new solid additive that can replace the widely used 1-chloronaphthalene additive.

Compromising Charge Generation and Recombination of Organic Photovoltaics with Mixed Diluent Strategy for Certified 19.4% Efficiency.

The ternary blend is demonstrated as an effective strategy to promote the device performance of organic photovoltaics (OPVs) due to the dilution effect. While the compromise between the charge generation and recombination remains a challenge. Here, a mixed diluent strategy for further improving the device efficiency of OPV is proposed. Specifically, the high-performance OPV system with a polymer donor, i.e., PM6, and a nonfullerene acceptor (NFA), i.e., BTP-eC9, is diluted by the mixed diluents, which involve a high bandgap NFA of BTP-S17 and a low bandgap NFA of BTP-S16 (similar with that of the BTP-eC9). The BTP-S17 of better miscibility with BTP-eC9 can dramatically enhance the open-circuit voltage (VOC ), while the BTP-S16 maximizes the charge generation or the short-circuit current density (JSC ). The interplay of BTP-17 and BTP-S16 enables better compromise between charge generation and recombination, thus leading to a high device performance of 19.76% (certified 19.41%), which is the best among single-junction OPVs. Further analysis on carrier dynamics validates the efficacy of mixed diluents for balancing charge generation and recombination, which can be further attributed to the more diverse energetic landscapes and improved morphology. Therefore, this work provides an effective strategy for high-performance OPV for further commercialization.

Over 31% efficient indoor organic photovoltaics enabled by simultaneously reduced trap-assisted recombination and non-radiative recombination voltage loss.

Indoor organic photovoltaics (OPVs) have shown great potential application in driving low-energy-consumption electronics for the Internet of Things. There is still great room for further improving the power conversion efficiency (PCE) of indoor OPVs, considering that the desired morphology of the active layer to reduce trap-assisted recombination and voltage losses and thus simultaneously enhance the fill factor (FF) and open-circuit voltage for efficient indoor OPVs remains obscure. Herein, by optimizing the bulk and interface morphology via a layer-by-layer (LBL) processing strategy, low leakage current and low non-radiative recombination loss can be synergistically achieved in PM6:Y6-O based devices. Detailed characterizations reveal the stronger crystallinity, purer domains and ideal interfacial contacts in the LBL devices compared to their bulk-heterojunction (BHJ) counterparts. The optimized morphology yields a reduced voltage loss and an impressive FF of 81.5%, and thus contributes to a high PCE of 31.2% under a 1000 lux light-emitting diode (LED) illumination in the LBL devices, which is the best reported efficiency for indoor OPVs. Additionally, this LBL strategy exhibits great universality in promoting the performance of indoor OPVs, as exemplified by three other non-fullerene acceptor systems. This work provides guidelines for morphology optimization and synergistically promotes the fast development of efficient indoor OPVs.

Precise Control of Selenium Functionalization in Non-Fullerene Acceptors Enabling High-Efficiency Organic Solar Cells.

Central π-core engineering of non-fullerene small molecule acceptors (NF-SMAs) is effective in boosting the performance of organic solar cells (OSCs). Especially, selenium (Se) functionalization of NF-SMAs is considered a promising strategy but the structure-performance relationship remains unclear. Here, we synthesize two isomeric alkylphenyl-substituted selenopheno[3,2-b]thiophene-based NF-SMAs named mPh4F-TS and mPh4F-ST with different substitution positions, and contrast them with the thieno[3,2-b]thiophene-based analogue, mPh4F-TT. When placing Se atoms at the outer positions of the π-core, mPh4F-TS shows the most red-shifted absorption and compact molecular stacking. The PM6 : mPh4F-TS devices exhibit excellent absorption, high charge carrier mobility, and reduced energy loss. Consequently, PM6 : mPh4F-TS achieves more balanced photovoltaic parameters and yields an efficiency of 18.05 %, which highlights that precisely manipulating selenium functionalization is a practicable way toward high-efficiency OSCs.

Design Rules of the Mixing Phase and Impacts on Device Performance in High-Efficiency Organic Photovoltaics.

In nonfullerene acceptor- (NFA-) based solar cells, the exciton splitting takes place at both domain interface and donor/acceptor mixture, which brings in the state of mixing phase into focus. The energetics and morphology are key parameters dictating the charge generation, diffusion, and recombination. It is revealed that tailoringthe electronic properties of the mixing region by doping with larger-bandgap components could reduce the density of state but elevate the filling state level, leading to improved open-circuit voltage (V OC) and reduced recombination. The monomolecular and bimolecular recombinations are shown to be intercorrelated, which show a Gaussian-like relationship with V OC and linear relationship with short-circuit current density (J SC) and fill factor (FF). The kinetics of hole transfer and exciton diffusion scale with J SC similarly, indicating the carrier generation in mixing region and crystalline domain are equally important. From the morphology perspective, the crystalline order could contribute to V OC improvement, and the fibrillar structure strongly affects the FF. These observations highlight the importance of the mixing region and its connection with crystalline domains and point out the design rules to optimize the mixing phase structure, which is an effective approach to further improve device performance.

Central Unit Fluorination of Non-Fullerene Acceptors Enables Highly Efficient Organic Solar Cells with Over 18 % Efficiency.

Halogenation of terminal of acceptors has been shown to give dramatic improvements in power conversion efficiencies (PCEs) of organic solar cells (OSCs). Similar significant results could be expected from the halogenation of the central units of state-of-the-art Y-series acceptors. Herein, a pair of acceptors, termed CH6 and CH4, featuring a conjugation-extended phenazine central unit with and without fluorination, have been synthesized. The fluorinated CH6 has enhanced molecular interactions and crystallinity, superior fibrillar network morphology and improved charge generation and transport in blend films, thus affording a higher PCE of 18.33 % for CH6-based binary OSCs compared to 16.49 % for the non-fluorinated CH4. The new central site offers further opportunities for structural optimization of Y-series molecules to afford better-performed OSCs and reveals the effectiveness of fluorination on central units.

A Transparent Electrode Based on Solution-Processed ZnO for Organic Optoelectronic Devices.

Achieving high-efficiency indium tin oxide (ITO)-free organic optoelectronic devices requires the development of high-conductivity and high-transparency materials for being used as the front electrode. Herein, sol-gel-grown zinc oxide (ZnO) films with high conductivity (460 S cm-1) and low optical absorption losses in both visible and near-infrared (NIR) spectral regions are realized utilizing the persistent photoinduced doping effect. The origin of the increased conductivity after photo-doping is ascribed to selective trapping of photogenerated holes by oxygen vacancies at the surface of the ZnO film. Then, the conductivity of the sol-gel-grown ZnO is further increased by stacking the ZnO using a newly developed sequential deposition strategy. Finally, the stacked ZnO is used as the cathode to construct ITO-free organic solar cells, photodetectors, and light emitting diodes: The devices based on ZnO outperform those based on ITO, owing to the reduced surface recombination losses at the cathode/active layer interface, and the reduced parasitic absorption losses in the electrodes of the ZnO based devices.

A Longitudinal Study on the Addictive Behaviors of General Population before and during the COVID-19 Pandemic in China.

By using nationally representative longitudinal data, this study investigates the effects of the COVID-19 pandemic on the addictive behaviors (smoking and drinking) of the general population in China. From the China Family Panel Studies (CFPS) 2018 and 2020, we extract a sample of individuals over 16 years of age in China, consisting of 14,468 individuals and 28,936 observations. We decompose the sample into three age groups, that is, ages between 16 and 39, ages between 40 and 59 and ages above 60. The bootstrap method is used to estimate the confidence interval of the difference in the mean of addictive behaviors, and logit models are used in the regression analysis. Our results show that the COVID-19 pandemic reduces the smoking behavior of individuals above 40 years of age, and that it reduces the drinking behavior of individuals above 16 years of age. However, the pandemic increases the smoking behavior of individuals between 16 and 39 years of age. These results may be closely related to the characteristics of COVID-19 (that is, a respiratory system disease), the working and economic pressures of young Chinese and the role of drinking alcohol in building and maintaining social networks in China.

Novel Third Components with (Thio)barbituric Acid as the End Groups Improving the Efficiency of Ternary Solar Cells.

Developing novel third component is critical for the ternary organic solar cells (TOSCs). Herein, we design and synthesize two novel third components, MAZ-1 and MAZ-2, with 1,3-diethyl-2-thiobarbituric acid and 1,3-dimethylbarbituric acid as the weak electron withdrawing end groups, respectively. Both MAZ-1 and MAZ-2 could improve the photovoltaic performance of the binary OSCs based on D18:Y6 which exhibit the power conversion efficiency (PCE) of 17%, because the third components can optimize the phase separation, suppress the bimolecular recombination, and decrease the nonradiative energy loss in ternary blends. The PCE of the optimized TOSCs approaches 18% along with the simultaneous increase in open circuit voltage, short circuit current density, and fill factor by incorporating 10 wt % MAZ-1 and MAZ-2 in acceptors. This work enriches the building blocks for novel third components for achieving highly efficient TOSCs.

Li-Doped ZnO Electron Transport Layer for Improved Performance and Photostability of Organic Solar Cells.

Organic solar cells (OSCs) based on an inverted architecture generally have better stability compared to those based on a standard architecture. However, the photoactive area of the inverted solar cells increases under ultraviolet (UV) or solar illuminatiom because of the too-high conductivity of the UV-illuminated zinc oxide (ZnO) interlayer. This limits the potential of the inverted solar cells for industrial applications. Herein, lithium-doped ZnO (Li-ZnO) films are employed as the cathode interlayer to construct inverted OSCs. The incorporation of Li ions is found to reduce the lateral conductivity of the UV-treated ZnO films because of the presence of Li ions, preventing the high-quality-growth of ZnO nanocrystals. This addresses the problem of having too-high conductivity in the UV-treated ZnO layer, causing the increased photoactive area of inverted solar cells. The overall performance of the solar cell is shown to be higher after the incorporation of Li ions in the ZnO layer, mainly due to the increased fill factor (FF), originating from the reduced trap-assisted recombination losses. Finally, the inverted solar cells based on the Li-ZnO interlayer are demonstrated to have a much better long-term stability, as compared to those based on ZnO. This allows the ZnO-based interlayers to be used for the mass production of organic solar cell modules.