Magnetization reversal in orthorhombic Sr-doped LaFe0.5Cr0.5O3-δ.

In this paper we studied the reversal magnetization of La1-x Sr x Fe0.5Cr0.5O3-δ (x = 0, 0.1 and 0.2) samples produced by combustion synthesis. The structural analysis was carried out by x-ray diffraction with Rietveld analysis. These analyses revealed that all samples have an orthorhombic structure with space group Pbnm (62) and that the Sr-doping induces a decrease of the lattice parameter. The x-ray photoelectron spectroscopy analysis indicates that the Sr-doping favor the change of the valence states of the Fe3+ to Fe4+. The magnetization as a function of the temperature reveals an unusual magnetic behavior with a reversal of magnetization. The increase of the Sr content induces a decrease of the temperature where occurs an inversion of the magnetization and do the value of the magnetization at 5 K more negative. This effect is attributed to the increase of the concentration of Fe4+ with increasing of the Sr content. The Fe and Cr with a valence of 4+ act as paramagnetic impurities in the antiferromagnetic lattice and are responsible for the changes in the magnetic behavior.

TiO2 anatase nanorods with non-equilibrium crystallographic {001} facets and their coatings exhibiting high photo-oxidation of NO gas.

Development of highly active photocatalysts is mandatory for more widespread application of this alternative environmental technology. Synthesis of photocatalysts, such as anatase TiO2, with more reactive, non-equilibrium, crystallographic facets is theoretically justified by a more efficient interfacial charge transfer to reactive adsorbed species, increasing quantum efficiency of photocatalyst. Air and vacuum calcinations of protonated trititanate nanotubes lead to their transformation to anatase nanorods. The nanorods synthesized by air calcination demonstrate photo-oxidation of NO gas more than three times superior to the one presented by the benchmark P-25 photocatalyst. This performance has been explained in terms of 50% higher specific surface area and, more importantly, through the predominance of more reactive, non-equilibrium, {001} crystallographic facets of the anatase nanorods. These facets present a high density of undercoordinated Ti cations, which favors adsorption of reactant species, and strained Ti-O-Ti bonds, leading to more efficient photo-oxidation reactions. Reduced Ti species, such as Ti3+, were not observed in the as-obtained nanorods, while reactive adsorbed molecules are scarce on the nanorods obtained through vacuum calcination. Dip-coating of TiO2 anatase nanorods (air calcined) over soda-lime glass plates was used to prepare visible light transparent, superhydrophilic and highly adherent photocatalytic coatings with homogenously distributed nanopores.

Growth and surface characterization of TiNbZr thin films deposited by magnetron sputtering for biomedical applications.

Low modulus of elasticity and the presence of non-toxic elements are important criteria for the development of materials for implant applications. Low modulus Ti alloys can be developed by designing ß-Ti alloys containing non-toxic alloying elements such as Nb and Zr. Actually, most of the metallic implants are produced with stainless steel (SS) because it has adequate bulk properties to be used as biomaterials for orthopedic or dental implants and is less expensive than Ti and its alloys, but it is less biocompatible than them. The coating of this SS implants with Ti alloy thin films may be one alternative to improve the biomaterial properties at a relatively low cost. Sputtering is a physical deposition technique that allows the formation of nanostructured thin films. Nanostructured surfaces are interesting when it comes to the bone/implant interface due to the fact that both the surface and the bone have nanoscale particle sizes and similar mechanical properties. TiNbZr thin films were deposited on both Si(111) and stainless steel (SS) substrates. The TiNbZr/Si(111) film was used as a model system, while the TiNbZr/SS film might improve the biocompatibility and extend the life time of stainless steel implants. The morphology, chemical composition, Young's modulus, and hardness of the films were analyzed by atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS), energy-dispersive X-ray spectroscopy (EDS), and nanoindentation.