Stability of wet versus dry bonding with different solvent-based adhesives.

OBJECTIVE: To evaluate the effects of surface moisture (wet or dry) and storage (24h or 3 months) on the microtensile bond strength (BS) of resin/dentin bonds mediated by two water/ethanol based adhesives Single Bond, 3M-ESPE, (SB) and Opti Bond Solo Plus, Kerr, (OB), and two acetone-based adhesives, One Step, Bisco, (OS) and Prime&Bond NT, Caulk/Dentsply, (PB). MATERIALS AND METHODS: Flat dentin surfaces were polished with 600-grit SiC paper, etched with 35% phosphoric acid for 15s and rinsed for 20s. Half the surface was maintained moist and the other half was air-dried for 30s. Each adhesive was applied simultaneously to both halves, left undisturbed for 30s and light-cured. Four-mm resin build-ups were constructed incrementally. After storage in water at 37 degrees C for 24h, slabs were produced by transversal sectioning and trimmed to an hourglass shape (0.8mm2). Half of the specimens were tested in tension at 0.6mm/min immediately after trimming and the other half after 3 months of water storage. Data were analyzed by two-way ANOVA and SNK for each material. RESULTS: Both moisture and storage affected BS to dentin, and was material-dependent. Dry bonding affected mostly the acetone-based adhesives. Larger reductions in bond strength were associated with dry bonding after 3 months of water storage. SIGNIFICANCE: Wet bonding resulted in more stable bonds over 3 months of water storage for most of the materials tested.

Effects of a combined application of potassium oxalate gel/adhesive agent on dentin permeability in vitro.

PURPOSE: To test the effects of sequential application of potassium oxalate gel/adhesive agent on in vitro dentin permeability. MATERIALS AND METHODS: Full crown preparations were made in extracted human molars to expose deep coronal dentin. The roots and pulp were removed and the resulting crown segments were connected to a special device (Flodec) to permit the measurement of the permeability of the specimens before and after treatments. Minimum and maximum permeability were recorded after smear layer and phosphoric acid treatment. A new smear layer was created and the permeability measured after the crowns were bonded with Single Bond (3M ESPE), One-Up Bond F (Tokuyama), and AdheSE (Ivoclar Vivadent), either according to manufacturer's instructions or after treating the acid-etched dentin with a 3 wt% potassium oxalate gel. The results were expressed as a percentage of maximum permeability values. Impressions and epoxy resin replicas from the crown segments were produced for SEM examination. RESULTS: None of the adhesives were able to eliminate the fluid flow through dentin. Two-way ANOVA revealed that the application of potassium oxalate prior to the bonding procedures was the most effective technique in reducingthe dentin permeability (p < 0.05), regardless of the adhesive used. SEM micrographs showed that transudation of dentinal fluid could be identified on the surfaces of all replicas. CONCLUSION: The use of potassium oxalate gel was effective in reducing the permeability of bonded dentin.

Influence of temperature on the spreading velocity of simplified-step adhesive systems.

BACKGROUND: Flowability and viscosity vary for different adhesive systems owing to differences in their composition. These characteristics can be modified by environmental temperature. PURPOSE: The purpose of this study was to determine the influence of temperature on the spreading (flow capacity) of simplified-step adhesive systems. MATERIALS AND METHODS: Spreading velocities of adhesive systems (Adper Single Bond and Single Bond Plus [3M ESPE, St. Paul, MN, USA]; Prime & Bond 2.1 and Prime & Bond NT [Dentsply Indústria e Comércio Ltda, Petrópolis, RJ, Brazil]; Adper Prompt [3M ESPE]; and One Up Bond F [Tokuyama Corp, Tokyo, Japan]) were analyzed at intervals of 10, 15, 20, and 30 seconds at both 25 degrees C and 37 degrees C by placing 10 microL drops on a glass slide surface with an inclination of 45 degrees. The spreading of each adhesive system was measured in millimeters per second. RESULTS: Data were analyzed by two-way analysis of variance and Student-Newman-Keuls tests. Regression analysis was used to determine a correlation between spreading velocity and time. Statistical significance was considered at a confidence level of 95%. Temperature influenced the spreading velocity, increasing it for Single Bond and Prime & Bond 2.1 and decreasing it for Adper Prompt (p < .05). No differences on spreading were observed for the other adhesives studied (p >.05). Regression analysis of each adhesive system demonstrated an inverse correlation between mean spreading velocity and time (R2 = .999) on both temperatures. CONCLUSIONS: Temperature increases yielded an increase of spreading for Single Bond and Prime & Bond 2.1. The influence of temperature on the spreading velocity was material dependent. CLINICAL SIGNIFICANCE: Environmental temperature can influence the rate of spreading of the adhesive system in clinically relevant times and may influence adhesive thickness on cavity walls.