Cycling of block copolymer composites with lithium-conducting ceramic nanoparticles.

Solid polymer and perovskite-type ceramic electrolytes have both shown promise in advancing solid-state lithium metal batteries. Despite their favorable interfacial stability against lithium metal, polymer electrolytes face issues due to their low ionic conductivity and poor mechanical strength. Highly conductive and mechanically robust ceramics, on the other hand, cannot physically remain in contact with redox-active particles that expand and contract during charge-discharge cycles unless excessive pressures are used. To overcome the disadvantages of each material, polymer-ceramic composites can be formed; however, depletion interactions will always lead to aggregation of the ceramic particles if a homopolymer above its melting temperature is used. In this study, we incorporate Li0.33La0.56TiO3 (LLTO) nanoparticles into a block copolymer, polystyrene-b-poly (ethylene oxide) (SEO), to develop a polymer-composite electrolyte (SEO-LLTO). TEMs of the same nanoparticles in polyethylene oxide (PEO) show highly aggregated particles whereas a significant fraction of the nanoparticles are dispersed within the PEO-rich lamellae of the SEO-LLTO electrolyte. We use synchrotron hard x-ray microtomography to study the cell failure and interfacial stability of SEO-LLTO in cycled lithium-lithium symmetric cells. Three-dimensional tomograms reveal the formation of large globular lithium structures in the vicinity of the LLTO aggregates. Encasing the SEO-LLTO between layers of SEO to form a "sandwich" electrolyte, we prevent direct contact of LLTO with lithium metal, which allows for the passage of seven-fold higher current densities without signatures of lithium deposition around LLTO. We posit that eliminating particle clustering and direct contact of LLTO and lithium metal through dry processing techniques is crucial to enabling composite electrolytes.

Evolution of Protrusions on Lithium Metal Anodes Stabilized by a Solid Block Copolymer Electrolyte Studied Using Time-Resolved X-ray Tomography.

Growing demand for rechargeable batteries with higher energy densities has motivated research focused on enabling the lithium metal anode. A prominent failure mechanism in such batteries is short circuiting due to the uncontrolled propagation of lithium protrusions that often have a dendritic morphology. In this paper, the electrodeposition of metallic lithium through a rigid polystyrene-b-poly(ethylene oxide) (PS-b-PEO or SEO) block copolymer electrolyte was studied using hard X-ray microtomography. In this system, protrusions were approximately ellipsoidal globules: we take advantage of this simple geometry to quantify their growth as a function of polarization time and electrolyte salt concentration. The growth of 47 different globules was tracked with time to obtain average velocities of globule growth into the electrolyte. The globule diameter was a linear function of globule height in the electrolyte with a slope of about 6, independent of time and electrolyte salt concentration.

Measurement of Three Transport Coefficients and the Thermodynamic Factor in Block Copolymer Electrolytes with Different Morphologies.

The design and engineering of composite materials is one strategy to satisfy the materials needs of systems with multiple orthogonal property requirements. In the case of rechargeable batteries with lithium metal anodes, the system requires a separator with fast lithium ion transport and good mechanical strength. In this work, we focus on the system polystyrene-block-poly(ethylene oxide) (SEO) with bis(trifluoromethane)sulfonimide lithium salt (LiTFSI). Ion transport occurs in the salt-containing poly(ethylene oxide)-rich domains. Mechanical rigidity arises due to the glassy nature of polystyrene (PS). If we assume that the salt does not interact with the PS-rich domains, we can describe ion transport in the electrolyte by three transport parameters (ionic conductivity, κ, salt diffusion coefficient, D, and cation transference number, t+0) and a thermodynamic factor, Tf. By systematically varying the volume fraction of the conducting phase, ϕc between 0.29 and 1.0, and chain length, N between 80 and 8000, we elucidate the role of morphology on ion transport. We find that κ is the strongest function of morphology, varying by three full orders of magnitude, while D is a weaker function of morphology. To calculate t+0 and Tf, we measure the current fraction, ρ+, and the open circuit potential, U, of concentration cells. We find that ρ+ and U follow universal trends as a function of salt concentration, regardless of chain length, morphology, or ϕc, allowing us to calculate t+0 for any SEO/LiTFSI or PEO/LiTFSI mixture when κ and D are known. The framework developed in this paper enables predicting the performance of any block copolymer electrolyte in a rechargeable battery.

Impact of Salt Concentration on Nonuniform Lithium Electrodeposition through Rigid Block Copolymer Electrolytes.

There is a growing demand for higher energy density lithium batteries. One approach for addressing this demand is enabling lithium metal anodes. However, nucleation and growth of electronically conductive protrusions, which cause short circuits, prevent the use of this technology with liquid electrolytes. The use of rigid solid electrolytes such as polystyrene-b-poly(ethylene oxide) electrolytes is one solution. An additional requirement for practical cells is needed to use electrolytes with high salt concentration to maximize the flux of lithium ions in the cell. The first systematic study of the effect of salt concentration on the morphology of electrodeposited lithium through a rigid block copolymer electrolyte is presented. The nature, areal density, and morphologies of defective lithium deposits created during galvanostatic cycling of lithium-lithium symmetric cells were determined using hard X-ray microtomography. Cycle life decreases rapidly with increasing salt concentration. X-ray microtomography reveals the presence of multiglobular protrusions, which are nucleated at impurity particles at low salt concentrations; here, the areal density of defective lithium deposits was independent of salt concentration. At the highest salt concentration, this density increases abruptly by a factor of about 10, and defects were also nucleated at locations where no impurities were visible.

Ohm's law for ion conduction in lithium and beyond-lithium battery electrolytes.

The viability of next generation lithium and beyond-lithium battery technologies hinges on the development of electrolytes with improved performance. Comparing electrolytes is not straightforward as multiple electrochemical parameters affect the performance of an electrolyte. Additional complications arise due to the formation of concentration gradients in response to dc potentials. We propose a modified version of Ohm's law to analyze current through binary electrolytes driven by a small dc potential. We show that the proportionality constant in Ohm's law is given by the product of the ionic conductivity, κ, and the ratio of currents in the presence (iss) and absence (iΩ) of concentration gradients, ρ+. The importance of ρ+ was recognized by Evans et al. [Polymer 28, 2324 (1987)]. The product κρ+ is used to rank order a collection of electrolytes. Ideally, both κ and ρ+ should be maximized, but we observe a trade-off between these two parameters, resulting in an upper bound. This trade-off is analogous to the famous Robeson upper bound for permeability and selectivity in gas separation membranes. Designing polymer electrolytes that overcome this trade-off is an ambitious but worthwhile goal.

3D Printed Absorber for Capturing Chemotherapy Drugs before They Spread through the Body.

Despite efforts to develop increasingly targeted and personalized cancer therapeutics, dosing of drugs in cancer chemotherapy is limited by systemic toxic side effects. We have designed, built, and deployed porous absorbers for capturing chemotherapy drugs from the bloodstream after these drugs have had their effect on a tumor, but before they are released into the body where they can cause hazardous side effects. The support structure of the absorbers was built using 3D printing technology. This structure was coated with a nanostructured block copolymer with outer blocks that anchor the polymer chains to the 3D printed support structure and a middle block that has an affinity for the drug. The middle block is polystyrenesulfonate which binds to doxorubicin, a widely used and effective chemotherapy drug with significant toxic side effects. The absorbers are designed for deployment during chemotherapy using minimally invasive image-guided endovascular surgical procedures. We show that the introduction of the absorbers into the blood of swine models enables the capture of 64 ± 6% of the administered drug (doxorubicin) without any immediate adverse effects. Problems related to blood clots, vein wall dissection, and other biocompatibility issues were not observed. This development represents a significant step forward in minimizing toxic side effects of chemotherapy.

Detection of the Order-to-Disorder Transition in Block Copolymer Electrolytes Using Quadrupolar 7Li NMR Splitting.

The order-to-disorder transition temperature (TODT) in a series of mixtures of polystyrene-b-poly(ethylene oxide) (SEO) and lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) salt is identified by the disappearance of a quadrupolar 7Li NMR triplet peak splitting above a critical temperature, where a singlet is observed. The macroscopic alignment of ordered domains required to produce a quadrupolar splitting occurs due to exposure to the NMR magnetic field. Alignment is confirmed using small-angle X-ray scattering (SAXS). The TODT determined by NMR is consistent with that determined using SAXS.

Phase Behavior of Mixtures of Block Copolymers and a Lithium Salt.

We present experimental results on the phase behavior of block copolymer/salt mixtures over a wide range of copolymer compositions, molecular weights, and salt concentrations. The experimental system comprises polystyrene- block-poly(ethylene oxide) and lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) salt. It is well established that LiTFSI interacts favorably with poly(ethylene oxide) relative to polystyrene. The relationship between chain length and copolymer composition at fixed temperature is U-shaped, as seen in experiments on conventional block copolymers and as anticipated from the standard self-consistent field theory (SCFT) of block copolymer melts. The phase behavior can be explained in terms of an effective Flory-Huggins interaction parameter between the polystyrene monomers and poly(ethylene oxide) monomers complexed with the salt, χeff, which increases linearly with salt concentration. The phase behavior of salt-containing block copolymers, plotted on a segregation strength versus copolymer composition plot, is similar to that of conventional (uncharged) block copolymer melts, when the parameter χeff replaces χ in segregation strength.

Reentrant phase behavior and coexistence in asymmetric block copolymer electrolytes.

It is known that the addition of salts to symmetric block copolymers leads to stabilization of ordered phases and an increase in domain spacing; both trends are consistent with an increase in the effective Flory-Huggins interaction parameter between the blocks, χ. In this work, we show that the addition of salt to a disordered asymmetric block copolymer first leads to the formation of coexisting ordered phases which give way to a reentrant disordered phase at a higher salt concentration. The coexisting phases are both body centered cubic (BCC) with different domain spacings, stabilized by partitioning of the salt. Further increase in salt concentration results in yet another disorder-to-order transition; hexagonally packed cylinders are obtained in the high salt concentration limit. The coexisting phases formed at intermediate salt concentration, elucidated by electron tomography, showed the absence of macroscopic regions with distinct BCC lattices. A different asymmetric block copolymer with composition in the vicinity of the sample described above only showed only a single disorder-to-order transition. However, the dependence of domain spacing on salt concentration was distinctly non-monotonic, and similar to that of the sample with the reentrant phase behavior. This dependence appears to be an announcement of reentrant phase transitions in asymmetric block copolymer electrolytes. These results cannot be mapped on to the traditional theory of block copolymer electrolyte self-assembly based on an effective χ.

Lightly Fluorinated Graphene as a Protective Layer for n-Type Si(111) Photoanodes in Aqueous Electrolytes.

The behavior of n-Si(111) photoanodes covered by monolayer sheets of fluorinated graphene (F-Gr) was investigated under a range of chemical and electrochemical conditions. The electrochemical behavior of n-Si/F-Gr and np(+)-Si/F-Gr photoanodes was compared to hydride-terminated n-Si (n-Si-H) and np(+)-Si-H electrodes in contact with aqueous Fe(CN)6(3-/4-) and Br2/HBr electrolytes as well as in contact with a series of outer-sphere, one-electron redox couples in nonaqueous electrolytes. Illuminated n-Si/F-Gr and np(+)-Si/F-Gr electrodes in contact with an aqueous K3(Fe(CN)6/K4(Fe(CN)6 solutions exhibited stable short-circuit photocurrent densities of ∼10 mA cm(-2) for 100,000 s (>24 h), in comparison to bare Si electrodes, which yielded nearly a complete photocurrent decay over ∼100 s. X-ray photoelectron spectra collected before and after exposure to aqueous anodic conditions showed that oxide formation at the Si surface was significantly inhibited for Si electrodes coated with F-Gr relative to bare Si electrodes exposed to the same conditions. The variation of the open-circuit potential for n-Si/F-Gr in contact with a series of nonaqueous electrolytes of varying reduction potential indicated that the n-Si/F-Gr did not form a buried junction with respect to the solution contact. Further, illuminated n-Si/F-Gr electrodes in contact with Br2/HBr(aq) were significantly more electrochemically stable than n-Si-H electrodes, and n-Si/F-Gr electrodes coupled to a Pt catalyst exhibited ideal regenerative cell efficiencies of up to 5% for the oxidation of Br(-) to Br2.