Novel indicators to better monitor the collection and recovery of (critical) raw materials in WEEE: Focus on screens.

Currently, in the European Union (EU), e-waste chain performance is assessed by technical indicators that aim to ensure system compliance with collection and recovery targets set by the WEEE Directive. This study proposes indicators to improve WEEE flow monitoring beyond the current overall weight-based approach, including complementary flows and treatment performance. A case study focused on the screen category in France is presented. In 2017, the collection rate of cathode-ray tube screens (CRT) was 68%, while for flat panel display (FPD) generated only 14% was collected. CRT screens have less precious and critical materials than FDP. Thus, elements like cobalt and gold highly concentrated in FPD, have a collection rate two to four times lower than elements such as copper (37%) which represents a high proportion in CRTs. Recycling is the main treatment in France. Nevertheless, the recycling rate per element varies significantly due to the low collection, and also the lack of technology and/or secondary raw materials market. The elements with higher recycling rates are base metals such as copper (28%), followed by precious metals like silver (23%), and gold (13%). Except for palladium, the recycling rate of the critical raw materials targeted in the study ranged from 6% (cobalt) to 0% (e.g. neodymium and indium). The results stress the need for indicators to support the development of WEEE chain from waste management to secondary (critical) raw materials suppliers.

Advances towards circular economy policies in the EU: The new Ecodesign regulation of enterprise servers.

The concept of a circular economy has been widely accepted by governments and industries. In Europe, the European Commission adopted the Circular Economy package in 2015. The Ecodesign Directive has been identified as one of the most suitable legislative tools for achieving some of the objectives in the package because it has the potential to translate the circular economy principles into specific product material efficiency requirements. This paper applies the Ecodesign policy process to "enterprise servers" to illustrate how circular economy strategies can be implemented by European product policies. Indeed, the paper introduces a potential novel approach to "operationalize" circular economy principles in product policies. The evolution of the material efficiency requirements for a more circular economy is described up to their final formulation, which is the one in the published Ecodesign regulation. This legal act includes requirements on design for disassembly, firmware availability, data deletion, and presence of critical raw materials. The process for enterprise servers has been successful as the early discussions between stakeholders, policymakers and experts, supported by appropriate metrics along an iterative debate, comes to the publications of material efficiency requirements in a regulation. This study represents a 'first-of-a-kind' experience, and sets precedents for the development of similar requirements for other product groups.

Circular economy indicators: What do they measure?

Circular Economy (CE) is a growing topic, especially in the European Union, that promotes the responsible and cyclical use of resources possibly contributing to sustainable development. CE is an umbrella concept incorporating different meanings. Despite the unclear concept, CE is turned into defined action plans supported by specific indicators. To understand what indicators used in CE measure specifically, we propose a classification framework to categorise indicators according to reasoning on what (CE strategies) and how (measurement scope). Despite different types, CE strategies can be grouped according to their attempt to preserve functions, products, components, materials, or embodied energy; additionally, indicators can measure the linear economy as a reference scenario. The measurement scope shows how indicators account for technological cycles with or without a Life Cycle Thinking (LCT) approach; or their effects on environmental, social, or economic dimensions. To illustrate the classification framework, we selected quantitative micro scale indicators from literature and macro scale indicators from the European Union 'CE monitoring framework'. The framework illustration shows that most of the indicators focus on the preservation of materials, with strategies such as recycling. However, micro scale indicators can also focus on other CE strategies considering LCT approach, while the European indicators mostly account for materials often without taking LCT into account. Furthermore, none of the available indicators can assess the preservation of functions instead of products, with strategies such as sharing platforms, schemes for product redundancy, or multifunctionality. Finally, the framework illustration suggests that a set of indicators should be used to assess CE instead of a single indicator.

Understanding lifetimes and failure modes of defective washing machines and dishwashers.

The available literature on average lifetimes and failure modes of household appliances is mainly based on results of surveys conducted among end-users, but very little precise information can be found on specific failure modes and repair rates. The main objective of this study is to provide quantitative data about frequent failures and average service lifetimes of two household appliances, through the analysis of repair services performed by professional repair operators. We based our analysis on available datasets provided by a representative independent repair centre based in Europe, and we focused on the failures most frequently occurring and the potential repair or discard of the appliances. A database of about 11,000 diagnoses on defective washing machines and dishwashers was analysed, and frequent failure modes and repair rates were identified. The analysis was supported by a tailored visualisation of results. Concerning washing machines, recurring failures diagnosed by the repair operator regarded the electronics, shock absorbers and bearings, doors, carbon brushes and pumps. While the highest repair rates (repaired devices over total diagnosed devices with a specific failure mode) were observed for doors, carbon brushes and removal of foreign objects, the lowest rates were observed for bearings, drums and tubs, circulation pumps and electronics. Regarding dishwashers, recurring failures involved pumps, electronics, aquastop and valves, foreign objects and doors. The lowest repair rates, however, were again observed for circulation pumps and electronics. We also observed that the average service lifetime of an appliance not repaired by repair centre operators is 12.6 years for washing machines and 12 years for dishwashers. This work brings important knowledge on lifetimes and failure modes of defective washing machines and dishwashers, concerning in particular weak and critical components, but also age of appliances to be repaired. Based on the exercise on the two appliances, we discuss a possible classification scheme for repair services of household appliances, including both information retrieved by professional repair operators and information retrieved through interviews with end-users.

How will second-use of batteries affect stocks and flows in the EU? A model for traction Li-ion batteries.

Although not yet developed in Europe, second-use of traction batteries enables an extension of their lifetime and potentially improves life cycle environmental performance. Li-ion batteries (LIBs) offer the most promising chemistry for traction batteries in electric vehicles (xEVs) and for second-use. Due to the novelty of the topic and the expected increase of e-mobility in the next decades, more efforts to understand the potential consequences of second-use of batteries from different perspectives are needed. This paper develops a dynamic, parameterised Material Flow Analysis (MFA) model to estimate stocks and flows of LIBs after their removal from xEVs along the specific processes of the european value-chain. Direct reuse, second-use and recycling are included in the model and parameters make it customisable and updatable. Focusing on full and plug-in electric vehicles, LIBs and energy storage capacity flows are estimated. Stocks and flows of two embedded materials relevant for Europe were also assessed (cobalt and lithium). Results showed that second-use corresponds to a better exploitation of LIBs' storage capacity. Meanwhile, Co and Li in-use stocks are locked in LIBs and their recovery is delayed by second-use; depending on the slower/faster development of second-use, the amount of Co available for recycling in 2030 ranges between 9% and 15% of Co demand and between 7 and 16% for Li. Uncertainty of inputs is addressed through sensitivity analysis. A variety of actors can use this MFA model to enhance knowledge of second-use of batteries in Europe and to support the effective management of LIBs along their value-chain.

Ease of disassembly of products to support circular economy strategies.

Circular economy strategies encourage, among others, concrete actions to extend the product lifetime. Product's repair and reuse, and component harvesting for reuse, all require the facilitated access to product components. Consequently, a reduction of the disassembly time and the related costs will increase the economic feasibility of product lifetime extension and therefore increase the viability of a circular economy in industrialised regions. Furthermore, disassembly has the potential to significantly increase the recycling yield and purity for precious metals, critical metals and plastics. For this reason, the European Commission and several ecolabels have considered to include design for disassembly requirements in legislation or voluntary environmental instruments. However, up to date, there is no standardised method to evaluate the ease of disassembly in an unambiguous manner with a good trade-off between the efforts required to apply the method and the accuracy of the determined disassembly time. The article proposes a robust method "eDiM" (ease of Disassembly Metric), to calculate the disassembly time based on the Maynard operation sequence technique (MOST). A straightforward calculation sheet is employed in eDiM to calculate the disassembly time given the sequence of actions and basic product information. This makes the results fully verifiable in an unambiguous manner, which makes eDiM suited to be used in policy measures in contrast to the results of prior developed methods One of the innovative aspects of eDiM is the categorization of disassembly tasks in six categories, which provides better insights on which disassembly tasks are the most time consuming and how the product design could be improved. The proposed method is illustrated by means of a case study of an LCD monitor. The presented case study demonstrates how the proposed method can be used in a policy context and how the calculated disassembly times per category can provide insights to manufacturers to improve the disassemblability of their products. The results also demonstrate how the proposed method can produce realistic results with only limited detail of input data.

Towards a durability test for washing-machines.

Durability plays a key role in enhancing resource conservation and contributing to waste minimization. The washing-machine product group represents a relevant case study for the development of a durability test and as a potential trigger to systematically address durability in the design of products. We developed a procedure to test the durability performance of washing-machines as a main objective of this research. The research method consisted of an analysis of available durability standards and procedures to test products and components, followed by an analysis of relevant references related to frequent failures. Finally, we defined the criteria and the conditions for a repeatable, relatively fast and relevant endurance test. The durability test considered the whole product tested under conditions of stress. A series of spinning cycles with fixed imbalanced loads was run on two washing-machines to observe failures and performance changes during the test. Even though no hard failures occurred, results clearly showed that not all washing-machines can sustain such a test without abrasion or performance deterioration. However, the attempt to reproduce the stress induced on a washing-machine by carrying out a high number of pure spinning cycles with fixed loads did not allow equal testing conditions: the actions of the control procedure regarding imbalanced loads differ from machine to machine. The outcomes of this research can be used as grounds to develop standardised durability tests and to, hence, contribute to the development of future product policy measures.

Accounting for the environmental benefits of remanufactured products: Method and application.

Although the importance of reusing products has been stated frequently, both in legislation and by academics, the scientific literature does not provide comprehensive and systematic methods of assessing the reuse of a generic product from an environmental point of view. Moreover, the definitions of reuse provided in the literature and legislation are not always consistent. This article introduces an original classification of different types of reuse, including some suggested definitions. It then focuses on remanufacturing, a type of reuse in which a used product (or its components) is returned to at least its original performance level. The article describes the development of a method for assessing, from a life-cycle perspective, the potential environmental benefits of remanufacturing energy-related products. The method includes several novel aspects: it helps to analyse possible trade-offs between potential environmental impacts and energy efficiency; it allows the independent modelling of some parameters that influence product reuse; and it can be applied even at the early stages of the design process, when some specifications may not yet have been defined. The environmental impacts of a product's life-cycle stages are used as input parameters for the assessment. The method is then applied to an enterprise server, a case-study product for which remanufacturing is a current market practice. A sensitivity analysis is included to check how uncertainties could affect the overall results. The results of the case study show that remanufactured servers, even those that are less energy efficient, can have lower environmental impacts than new ones. For example, reusing some components (e.g. hard disk drives and memory cards) is environmentally beneficial even if the remanufactured server consumes up to 7% more energy than a newly manufactured server. The case study also demonstrates how the method proposed could be used in the context of product policy discussions.

In search of standards to support circularity in product policies: A systematic approach.

The aspiration of a circular economy is to shift material flows toward a zero waste and pollution production system. The process of shifting to a circular economy has been initiated by the European Commission in their action plan for the circular economy. The EU Ecodesign Directive is a key policy in this transition. However, to date the focus of access to market requirements on products has primarily been upon energy efficiency. The absence of adequate metrics and standards has been a key barrier to the inclusion of resource efficiency requirements. This paper proposes a framework to boost sustainable engineering and resource use by systematically identifying standardization needs and features. Standards can then support the setting of appropriate material efficiency requirements in EU product policy. Three high-level policy goals concerning material efficiency of products were identified: embodied impact reduction, lifetime extension and residual waste reduction. Through a lifecycle perspective, a matrix of interactions among material efficiency topics (recycled content, re-used content, relevant material content, durability, upgradability, reparability, re-manufacturability, reusability, recyclability, recoverability, relevant material separability) and policy goals was created. The framework was tested on case studies for electronic displays and washing machines. For potential material efficiency requirements, specific standardization needs were identified, such as adequate metrics for performance measurements, reliable and repeatable tests, and calculation procedures. The proposed novel framework aims to provide a method by which to identify key material efficiency considerations within the policy context, and to map out the generic and product-specific standardisation needs to support ecodesign. Via such an approach, many different stakeholders (industry, academics, policy makers, non-governmental organizations etc.) can be involved in material efficiency standards and regulations. Requirements and standards concerning material efficiency would compel product manufacturers, but also help designers and interested parties in addressing the sustainable resource use issue.

Background qualitative analysis of the European Reference Life Cycle Database (ELCD) energy datasets - part I: fuel datasets.

INTRODUCTION: The aim of this study is to identify areas of potential improvement of the European Reference Life Cycle Database (ELCD) fuel datasets. CASE DESCRIPTION: The revision is based on the data quality indicators described by the ILCD Handbook, applied on sectorial basis. These indicators evaluate the technological, geographical and time-related representativeness of the dataset and the appropriateness in terms of completeness, precision and methodology. DISCUSSION AND EVALUATION: Results show that ELCD fuel datasets have a very good quality in general terms, nevertheless some findings and recommendations in order to improve the quality of Life-Cycle Inventories have been derived. Moreover, these results ensure the quality of the fuel-related datasets to any LCA practitioner, and provide insights related to the limitations and assumptions underlying in the datasets modelling. CONCLUSIONS: Giving this information, the LCA practitioner will be able to decide whether the use of the ELCD fuel datasets is appropriate based on the goal and scope of the analysis to be conducted. The methodological approach would be also useful for dataset developers and reviewers, in order to improve the overall DQR of databases.

Method applied to the background analysis of energy data to be considered for the European Reference Life Cycle Database (ELCD).

Under the framework of the European Platform on Life Cycle Assessment, the European Reference Life-Cycle Database (ELCD - developed by the Joint Research Centre of the European Commission), provides core Life Cycle Inventory (LCI) data from front-running EU-level business associations and other sources. The ELCD contains energy-related data on power and fuels. This study describes the methods to be used for the quality analysis of energy data for European markets (available in third-party LC databases and from authoritative sources) that are, or could be, used in the context of the ELCD. The methodology was developed and tested on the energy datasets most relevant for the EU context, derived from GaBi (the reference database used to derive datasets for the ELCD), Ecoinvent, E3 and Gemis. The criteria for the database selection were based on the availability of EU-related data, the inclusion of comprehensive datasets on energy products and services, and the general approval of the LCA community. The proposed approach was based on the quality indicators developed within the International Reference Life Cycle Data System (ILCD) Handbook, further refined to facilitate their use in the analysis of energy systems. The overall Data Quality Rating (DQR) of the energy datasets can be calculated by summing up the quality rating (ranging from 1 to 5, where 1 represents very good, and 5 very poor quality) of each of the quality criteria indicators, divided by the total number of indicators considered. The quality of each dataset can be estimated for each indicator, and then compared with the different databases/sources. The results can be used to highlight the weaknesses of each dataset and can be used to guide further improvements to enhance the data quality with regard to the established criteria. This paper describes the application of the methodology to two exemplary datasets, in order to show the potential of the methodological approach. The analysis helps LCA practitioners to evaluate the usefulness of the ELCD datasets for their purposes, and dataset developers and reviewers to derive information that will help improve the overall DQR of databases.

Background qualitative analysis of the European reference life cycle database (ELCD) energy datasets - part II: electricity datasets.

The aim of this paper is to identify areas of potential improvement of the European Reference Life Cycle Database (ELCD) electricity datasets. The revision is based on the data quality indicators described by the International Life Cycle Data system (ILCD) Handbook, applied on sectorial basis. These indicators evaluate the technological, geographical and time-related representativeness of the dataset and the appropriateness in terms of completeness, precision and methodology. Results show that ELCD electricity datasets have a very good quality in general terms, nevertheless some findings and recommendations in order to improve the quality of Life-Cycle Inventories have been derived. Moreover, these results ensure the quality of the electricity-related datasets to any LCA practitioner, and provide insights related to the limitations and assumptions underlying in the datasets modelling. Giving this information, the LCA practitioner will be able to decide whether the use of the ELCD electricity datasets is appropriate based on the goal and scope of the analysis to be conducted. The methodological approach would be also useful for dataset developers and reviewers, in order to improve the overall Data Quality Requirements of databases.