Zero-power infrared digitizers based on plasmonically enhanced micromechanical photoswitches.

State-of-the-art sensors use active electronics to detect and discriminate light, sound, vibration and other signals. They consume power constantly, even when there is no relevant data to be detected, which limits their lifetime and results in high costs of deployment and maintenance for unattended sensor networks. Here we propose a device concept that fundamentally breaks this paradigm-the sensors remain dormant with near-zero power consumption until awakened by a specific physical signature associated with an event of interest. In particular, we demonstrate infrared digitizing sensors that consist of plasmonically enhanced micromechanical photoswitches (PMPs) that selectively harvest the impinging electromagnetic energy in design-defined spectral bands of interest, and use it to create mechanically a conducting channel between two electrical contacts, without the need for any additional power source. Our zero-power digitizing sensor prototypes produce a digitized output bit (that is, a large and sharp off-to-on state transition with an on/off conductance ratio >1012 and subthreshold slope >9 dec nW-1) when exposed to infrared radiation in a specific narrow spectral band (∼900 nm bandwidth in the mid-infrared) with the intensity above a power threshold of only ∼500 nW, which is not achievable with any existing photoswitch technologies.

Interfacial shear stress between a single-walled carbon nanotube and a gold surface after different physical treatments.

The interfacial shear stress between gold and dielectrophoretically assembled single-walled carbon nanotubes can be increased by annealing in N2, by e-beam irradiation, or by e-beam deposition of carbon. For the first time this increase has been measured, using a technique developed by this group that is based on NEMS cantilever measurements combined with modeling. Annealing increases the shear stress by more than a factor of 3 over its value of 87MPa for untreated gold surfaces, while e-beam irradiation increases the shear stress by more than a factor of 2 and carbon deposition increases the shear stress by a smaller amount.

Interfacial shear stress between single-walled carbon nanotubes and gold surfaces with and without an alkanethiol monolayer.

A novel and effective technique is developed to make the first determination of shear stress between dielectrophoretically assembled single-walled carbon nanotubes (SWNTs) and surfaces. The results demonstrate that we can vary the shear stress by a factor of 20 by functionalizing a gold surface with different alkanethiols. The interfacial shear stress between a small bundle of SWNTs and a gold surface with and without self-assembled monolayers of alkanethiol (2-phenylethanethiol or 2-aminoethanethiol) is determined. The measurements are based on simple NEMS cantilever beams, a nanomanipulator, and a scanning electron microscope (SEM). It is emphasized that the measured quantity is the slack in the nanotube (not the shear stress) induced by the nanomanipulation. The shear stress is determined from the slack through a mechanics model. An average shear stress of 87 MPa between SWNTs and gold surfaces is obtained. For the tests on the self-assembled 2-aminoethanethiol surface, an average shear stress of 142 MPa is obtained. For the self-assembled 2-phenylethanethiol surface, the shear stress is determined to be around 7.2 MPa with an estimated work of adhesion of 0.5 J/m(2).

Substituent effects in pentacenes: gaining control over HOMO-LUMO gaps and photooxidative resistances.

A combined experimental and computational study of a series of substituted pentacenes including halogenated, phenylated, silylethynylated and thiolated derivatives is presented. Experimental studies include the synthesis and characterization of six new and six known pentacene derivatives and a kinetic study of each derivative under identical photooxidative conditions. Structures, HOMO-LUMO energies and associated gaps were calculated at the B3LYP/6-311+G**//PM3 level while optical and electrochemical HOMO-LUMO gaps were measured experimentally. The combined results provide for the first time a quantitative assessment of HOMO-LUMO gaps and photooxidative resistances for a large series of pentacene derivatives as a function of substituents. The persistence of each pentacene derivative is impacted by a combination of steric resistance and electronic effects as well as the positional location of each substituent. Silylethynyl-substituted pentacenes like TIPS-pentacene possess small HOMO-LUMO gaps but are not the longest lived species under photooxidative conditions, contrary to popular perception. A pentacene derivative with both chlorine substituents in the 2,3,9,10 positions and o-alkylphenyl substituents in the 6,13 positions is longer lived than TIPS-pentacene. Of all the derivatives studied, alkylthio- and arylthio-substituted pentacenes are most resistant to photooxidation, possess relatively small HOMO-LUMO gaps and are highly soluble in a variety of organic solvents. These results have broad implications for the field of organic molecular electronics where OFET, OLED, and other applications can benefit from highly persistent, solution processable pentacene derivatives.

A finite element model of loading and unloading of an asperity contact with adhesion and plasticity.

An elastic-plastic microcontact with adhesion was studied using a finite element model. This model differs from the existing models, in that it includes the effect of adhesion on the deformation and stresses field, making it applicable to a wide range of material properties. It shows two distinct separation modes, brittle separation and ductile separation. To the best of our knowledge this is the first time that a finite element model has predicted ductile separation in an adhesive contact. Three key parameters affecting the contact and separation modes are also discussed. Further work is expected to fully reveal the effect of these parameters on the separation modes.