Transport and targeted binding of Pluronic-coated nanoparticles in unsaturated porous media.

The effectiveness of most in situ remedial technologies, including nanoremediation, lies on successful delivery of reagents to a subsurface target treatment zone. Targeted delivery of engineered nanoparticles (NPs) to treat petroleum hydrocarbons present in the unsaturated zone requires an understanding of their transport behaviour in these systems. A series of column experiments explored the effect of initial water saturation, flowrate, input dosage, and porous medium texture on the transport of iron oxide or cobalt ferrite NPs coated with an amphiphilic co-polymer, as well as their targeted attachment to a crude oil zone. As the initial water content increased with a concomitant reduction in air saturation, the degree of tailing present in the NP breakthrough curves (BTCs) reduced, and the mass of NPs recovered increased. Air saturation is positively correlated with the magnitude of air-water interfaces, which provide additional NP retention sites. At a lower injection flow rate, NP retention increased due to a longer residence time and comparatively high air saturation. NP transport behaviour was not sensitive to NP injection dose over the range tested. Increased retention and retardation of the NP BTC was observed in sediments with a higher clay and silt content. NPs coated with a lower concentration of a Pluronic block co-polymer to promote binding were preferentially retained within the crude oil zone. To simulate the asymmetrical NP breakthrough curves observed from the unsaturated systems required the use of a model that accounted for both mobile and immobile flow regions as well as NP attachment and detachment with nonlinear Langmuirian blocking. This model allowed examination of attachment and detachment rate coefficients which captured NP interaction with the porous medium and/or crude oil. It was found that the initial water saturation and flow rate did not have an appreciable impact on the NP attachment rate coefficient, while it increased by ~10× with increasing clay and silt content, and by ~100× in the presence of crude oil, indicating preferential NP attachment within the crude oil zone. As a result of the lower NP polymer concentration coating used to promote increased attachment to crude oil, higher retention was observed near the column inlet and was captured quantitatively by adding a depth-dependent straining term to the model. This retention behaviour represents a combination of irreversible attachment at the air-water interfaces and straining near the column inlet enhanced by the formation of NP aggregates. The detachment rate coefficient decreased with a lower initial water saturation and flowrate, but increased with higher clay and silt content. The findings from this study contribute to our understanding of the transport and binding behaviour of Pluronic-coated NPs in unsaturated conditions and, in particular, the role of initial water content, flowrate and porous medium texture. Demonstrated delivery of NPs to a target zone is an important step towards expanding the utility of NPs as treatment reagents.

Factors affecting pluronic-coated iron oxide nanoparticle binding to petroleum hydrocarbon-impacted sediments.

Effective targeted delivery of nanoparticle agents may enhance the remediation of soils and site characterization efforts. Nanoparticles coated with Pluronic, an amphiphilic block co-polymer, demonstrated targeted binding behaviour toward light non-aqueous phase liquids such as heavy crude oil. Various factors including coating concentration, oil concentration, oil type, temperature, and pH were assessed to determine their effect on nanoparticle binding to heavy crude oil-impacted sandy aquifer material. Nanoparticle binding was increased by decreasing the coating concentration, increasing oil concentration, using heavier oil types, and increasing temperature, while pH over the range of 5-9 was found to have no effect. Nanoparticle transport and binding in columns packed with clean and oily porous media demonstrated the ability for efficient nanoparticle targeted binding. For the conditions explored, the attachment rate coefficient in columns packed with clean sand was 2.10 ± 0.66 × 10-4 s-1; however, for columns packed with oil-impacted sand a minimum attachment rate coefficient of 8.86 ± 0.43 × 10-4 s-1 was estimated. The higher attachment rate for the oil-impacted sand system indicates that nanoparticles may preferentially accumulate to oil-impacted zones present at heterogeneous impacted sites. Simulations were used to demonstrate this hypothesis using the set of parameters generated in this effort. This work contributes to our understanding of the application conditions that are required for efficient targeted binding of nanoparticles to crude-oil impacted porous media.

Targeted nanoparticle binding & detection in petroleum hydrocarbon impacted porous media.

Targeted nanoparticle binding has become a core feature of experimental pharmaceutical product design which enables more efficient payload delivery and enhances medical imaging by accumulating nanoparticles in specific tissues. Environmental remediation and geophysical monitoring encounter similar challenges which may be addressed in part by the adoption of targeted nanoparticle binding strategies. This study illustrates that engineered nanoparticles can bind to crude oil-impacted silica sand, a selective adsorption driven by active targeting based on an amphiphilic polymer coating. This coating strategy resulted in 2 mg/kg attachment to clean silica sand compared to 8 mg/kg attachment to oil-impacted silica sand. It was also shown that modifying the surface coating influenced the binding behaviour of the engineered nanoparticles - more hydrophobic polymers resulted in increased binding. Successful targeting of Pluronic-coated iron oxide nanoparticles to a crude oil and silica sand mixture was demonstrated through a combined quantitative Orbital Emission Spectroscopy mass analysis supported by Vibrating Scanning Magnetometer magnetometry, and a qualitative X-ray micro-computed tomography (CT) visualization approach. These non-destructive characterization techniques facilitated efficient analysis of nanoparticles in porous medium samples with minimal sample preparation, and in the case of X-Ray CT, illustrated how targeted nanoparticle binding may be used to produce 3-D images of contaminated porous media. This work demonstrated successful implementation of nanoparticle targeted binding toward viscous LNAPL such as crude oil in the presence of a porous medium, a step which opens the door to successful application of targeted delivery technology in environmental remediation and monitoring.

Remediation of heavy hydrocarbon impacted soil using biopolymer and polystyrene foam beads.

A green chemistry solution is presented for the remediation of heavy hydrocarbon impacted soils. The two-phase recovery system relies on a plant-based biopolymer, which releases hydrocarbons from soil, and polystyrene foam beads, which recover them from solids and water. The efficiency of the process was demonstrated by comparisons with control experiments, where water, biopolymer, or beads alone yielded total petroleum hydrocarbon (TPH) reductions of 25%, 52%, and 58%, respectively, compared to 94% when 1.25 mL of 1% biopolymer and 15 mg beads per gram of soil were agitated for 30 min. Reductions in TPH content were substantial regardless of soil fraction, with removals of 97%, 91%, and 75% from sand, silt, and clay size fractions, respectively. Additionally, treatment efficiency was independent of carbon number, C13 to C43, as demonstrated by reductions in both diesel fuel (C13-C28) and residual-range organics (C25-C43) of ∼90%. Compared to other published polymer- and surfactant-based treatment methods, this system requires less mobilizing agent, sorbent, and mixing time. The remediation process is both efficient and sustainable because the biopolymer is re-useable and sourced from renewable crops and polystyrene beads are obtained from recycled materials.