RESUMO
PURPOSE: Attempts have been made to decontaminate the implant surface by using diode lasers. However, the parameters that provide efficient decontamination without altering the topography or surface characteristics of titanium implants are still unclear. The aim of the present study was to evaluate the effect of altering the power of diode laser (940 nm) application on the hydrophilicity, surface topography, and chemical composition of sandblasted, large grit, acid-etched (SLA) treated titanium alloy implant surface. MATERIALS AND METHODS: Thirty-six SLA-treated titanium discs (Dentis Co., Ltd.) were used in this study. The hydrophilicity of all discs was measured by using a contact angle goniometer (190 CA; Rame-hart Co, Ltd). Discs were randomly divided into four groups (n = 9 each) based on the power of the diode laser used. Group I (control, no lasing group), group II: treated with 1 W power, group III: 2 W power, and group IV: 3 W power. The chemical composition of the SLA discs was evaluated by using energy dispersive x-ray spectroscopy (EDX) before laser application. Hydrophilicity was reevaluated after the application of laser irradiation. The surface topography of all discs was examined. Changes in the chemical composition of the titanium discs were investigated following the lasing procedure. Morphometric analysis of the surface area (µm2 ) of the indentations created following laser application was also evaluated. Data were collected and the Shapiro-Wilk test of normality was used. Comparisons between the four study groups were done by using the Kruskal-Wallis test, while that to evaluate the morphometric analysis of the surface area was done by using One-way ANOVA (P < 0.05). RESULTS: The average contact angle of the drop of distilled water to the SLA discs significantly decreased after laser treatment (P < 0.05). The largest contact angle was measured in the control group, followed by the 1 W group, and the 2 W group. The smallest angle was measured in the 3 W group. Considerable surface alterations such as melting and flattening were observed on examination of the surface topography of the 3 W group followed by the 2 W group. The least changes were observed in association with the 1 W group in comparison to the control group. The EDX analysis showed the appearance of peaks of the oxygen and carbon elements after the lasing procedure with the highest percentage in the 3 W group. The average of the surface area of the created indentations significantly increased with increasing the power of the diode laser used (P < 0.05). CONCLUSIONS: The application of diode laser (940 nm) with 2 W and 3 W powers significantly altered the hydrophilicity, the surface topography, and the chemical composition of titanium discs. Diode laser (940 nm) with 1 W power can be safely used on SLA titanium implant surfaces with no damaging effect on the surface topography or hydrophilicity.
RESUMO
BACKGROUND: Straight preparable abutments and titanium bases (ti-base) can be used to support single-unit screw-retained lithium disilicate implant-supported restorations. The choice between using both abutments depends on many factors. The purpose of this in vitro study was to compare the masking ability, marginal adaptation, and fracture resistance of screw-retained lithium disilicate implant-supported crowns cemented to straight preparable abutments and ti-bases. METHODS: Twenty laboratory implant analogs (Straumann Bone Level; Straumann AG) were randomly divided into 2 groups (n = 10 each) according to the type of the abutment used. Preparable abutment group and ti-base group. Lithium disilicate crowns were used to restore the specimens. All specimens were subjected to thermocycling (from 5 to 55 °C for 2000 cycles) followed by cyclic loading (120 000 cycles). The vertical marginal gap between the abutment finish line and the most apical part of the crown was measured in (µm) by using a stereomicroscope after cementation and after thermocycling and cyclic loading. A spectrophotometer was used to evaluate the masking ability of the specimens after cementation. The load required to fracture the crowns was measured in Newtons (N) by using a universal testing machine after thermocycling and cyclic loading. The Shapiro-Wilk test of normality was used. The appropriate statistical test was used. RESULTS: Regarding the masking ability, the color difference (∆E) showed no statistically significant difference between the ti-base group (2.6 ± 0.2) and the preparable abutment group (2.6 ± 0.3) (P = .888). The average of the microgap values (µm) was greater in ti-basegroup after cementation (13.9 ± 9.2) than preparable group (7.63 ± 1.78) with no statistically significant difference between the 2 groups (P = .49). After cyclic loading and thermocycling, the average microgap values (µm) was significantly greater in the ti base group (21.3 ± 7.4) than in preparable group (13.3 ± 1.5) (P = .02). The load required to fracture the specimens was greater in the preparable group (1671.5 ± 143.8) than in the ti-base group (1550.2 ± 157.5) with no statistically significant difference between the 2 groups (P = .089). CONCLUSION: The abutments used in the present study did not compromise the masking ability of the screw-retained lithium disilicate implant supported crowns. Moreover, the crowns cemented to preparable abutments had better marginal adaptation and higher fracture resistance when compared to those cemented to ti-bases. CLINICAL IMPLICATIONS: Straight preparable abutments are considered as an alternative to the ti-bases when restoring single screw-retained lithium disilicate implant-supported crowns with comparable fracture resistance, marginal adaptation, and masking ability.
Assuntos
Implantes Dentários , Titânio , Humanos , Parafusos Ósseos , CoroasRESUMO
STATEMENT OF PROBLEM: The OT BRIDGE connection system can be an alternative to multiunit abutments (MUA) for patients with all-on-four implant-supported restorations. However, the amount of prosthetic screw loosening of the OT BRIDGE in comparison with the MUA used in all-on-four implant restorations is unclear. PURPOSE: The purpose of this in vitro study was to compare the loss of removal torque in the absence of load and after dynamic cyclic loading between the 2 different connection systems: OT BRIDGE attachment and MUA used in all-on-four implant-supported restorations. MATERIAL AND METHODS: Four dummy implants (Neobiotech Co Ltd) were inserted into an edentulous mandibular model according to the all-on-four concept. Sixteen screw-retained restorations were digitally fabricated and assigned to 2 groups: the OT BRIDGE group received 8 restorations connected with OT BRIDGE (Rhein 83 srl); the MUA group received 8 restorations connected with MUA (Neobiotech Co Ltd). Restorations were tightened to the abutments according to the manufacturers' recommendations by using a digital torque gauge. The removal torque value (RTV) was measured with the same digital torque gauge. After retightening, dynamic cyclic loading was applied by using a pneumatic custom cyclic loading machine. RTV after loading was measured with the same torque gauge. From the RTVs measured, the ratios of removal torque loss (RTL) before and after loading and the difference between before and after loading were calculated. Data were analyzed by using the independent samples t test, paired samples t test, and mixed model analysis of variance (α=.05). RESULTS: The OT BRIDGE showed significantly higher RTL before loading ratio (%) than the MUA in anterior abutments (P=.002) and posterior abutments (P=.003), as well as significantly higher RTL after loading ratio (%) in anterior abutments (P=.02). The MUA showed significantly higher RTL difference between before and after loading ratio (%) than the OT BRIDGE in both anterior (P=.001) and posterior abutments (P<.001). In both systems, posterior abutments showed significantly higher RTL after loading ratio (%) than anterior abutments (P<.001). CONCLUSIONS: Posterior abutments showed more prosthetic screw loosening than anterior ones in both systems. The OT BRIDGE showed higher total prosthetic screw loosening than the MUA, although this was not significant in posterior abutments after loading. However, the OT BRIDGE was less affected by cyclic loading than the MUA.
RESUMO
STATEMENT OF PROBLEM: Straight preparable abutments provide an alternative to titanium bases (Ti-bases) for single-unit screw-retained implant-supported restorations. However, the debonding force between crowns with a screw access channel cemented to preparable abutments and Ti-bases of different designs and surface treatments is unclear. PURPOSE: The purpose of this in vitro study was to compare the debonding force of screw-retained lithium disilicate implant-supported crowns cemented to straight preparable abutments and Ti-bases of different designs and surface treatments. MATERIAL AND METHODS: Forty laboratory implant analogs (Straumann Bone Level) were embedded into epoxy resin blocks that were randomly divided into 4 groups (n=10 each) according to the abutment type used: CEREC group, Variobase group, airborne-particle abraded Variobase group, and airborne-particle abraded straight preparable abutment group. All specimens were restored with lithium disilicate crowns and cemented with resin cement to the corresponding abutments. They were thermocycled (from 5 to 55 °C for 2000 cycles) followed by cyclic loading (120 000 cycles). The tensile forces required to debond the crowns from the corresponding abutments were measured (N) by using a universal testing machine. The Shapiro-Wilk test of normality was used. Comparison between the study groups was done with 1-way ANOVA (α=.05). RESULTS: Tensile debonding force values were significantly different according to the type of abutment used (P<.05). The highest retentive force value was recorded in the straight preparable abutment group (928.1 ±222.2 N) followed by the airborne-particle abraded Variobase group (852.6 ±164.6 N), and the CEREC group (498.8 ±136.6 N); the lowest value was reported in the Variobase group (158.6 ±85.2 N). CONCLUSIONS: The retention of screw-retained lithium disilicate implant-supported crowns cemented to airborne-particle abraded straight preparable abutments is significantly higher than to non-surface treated Ti-bases and similar to airborne-particle abraded ones. Abrading abutments with 50-mm Al2O3 significantly increased the debonding force of the lithium disilicate crowns.
