Is it necessary to tie the medial row in rotator cuff repair double-row constructs when using suture tape?

PURPOSE: To evaluate the selected biomechanical differences of a double-row trans-osseous equivalent rotator cuff repair with a knotless versus knot-tying medial row using suture tape in regard to repair displacement, stiffness, and ultimate load to failure. METHODS: In 16 fresh-frozen human shoulders (8 matched pairs), double-row rotator cuff repairs were performed with medial-row mattress knots (MK) on one side, the other without (NK). Two DVRT (Differential Variable Reluctance Transducer) sensors were attached between the humerus and 3 mm above the repair site and were used to measure the displacement across the repair during cycling. The biomechanical parameters measured were repair displacement, stiffness, and ultimate load to failure. The supraspinatus was loaded in a similar fashion to previously described protocol using cyclic loading and load to failure testing.1. RESULTS: All data from paired specimens were compared using paired Student t tests. No statistically significant difference (SSD) in displacement across the repair over the 200 cycles of the test was noted between the two groups (MK = 0.591 ± 0.501 mm; NK = 0.439 ± 0.417 mm, p = 0.618). No SSD in stiffness was noted between the two groups (MK = 32.87 ± 6.31 N/mm; NK = 27.98 ± 9.69 N/mm, p = 0.120). No SSD in ultimate load to failure was noted between the two groups (MK = 501.2 ± 126.1 N; NK = 416.8 ± 120.0 N, p = 0.116). CONCLUSION: There was no statistically significant different between knotless versus knotted medial row double row rotator cuff repair constructs using suture tape in regard to displacement across the repair site, stiffness and ultimate load to failure. Despite previous evidence suggesting inferiority of knotless medial row technique using suture constructs, this evidence may support the biomechanical equivalency of knotless medial row technique using suture tape.

Biomechanical study of 4-hole pubic symphyseal plating: locked versus unlocked constructs.

To the authors' knowledge, no published studies have examined the use of locking plates on injuries of the anterior pelvic ring. The purpose of this study was to determine whether locked plates provide enhanced stability in the treatment of pubic symphyseal disruptions. Completely unstable pelvic injuries were simulated in pelvic Sawbones (model 1301; Pacific Research Laboratories, Vashon, Washington) and 2 different fixation constructs used for anterior fixation (4-hole, 3.5-mm pubic symphysis plate with all locked or all unlocked screws). Adjunctive sacroiliac screw fixation with a single 7.3-mm screw placed into S1 was used in all specimens. Specimens were analyzed for motion at the pubic symphysis and sacroiliac joints using a Material Testing System (MTS Systems Corporation, Eden Prairie, Minnesota). Each specimen was subjected to compressive loading in a single-limb stance. Side loading was also examined. The main outcome measurement was motion at the pubic symphysis and sacroiliac joints and overall construct stiffness. No significant difference existed in overall construct stiffness between the 2 methods of pubic symphysis fixation. The motions at the pubic symphysis or injured sacroiliac joints were not significantly different. In addition, motion at the pubic symphysis joint with lateral load was not improved with a locking construct.No significant difference existed between 4-hole locked or unlocked constructs used for fixation of the pubic symphysis. No apparent advantage of locking screws exists for disruptions of the pubic symphysis, and recent reports have questioned the possibility of catastrophic failure.

Minimal versus maximal plate fixation techniques of the ulna: the biomechanical effect of number of screws and plate length.

OBJECTIVE: To test the hypothesis that longer plates with the minimum number of screws provide equivalent or superior strength of fixation to standard compression plating using the maximum number of screws. DESIGN: Prospective analysis of biomechanical data was performed. SETTING: In vitro experimentation. INTERVENTIONS: A reproducible osteotomy was made in formalin-fixed ulnae. The osteotomies were stabilized employing six-, eight-, or ten-hole plates with two screws in the outermost holes and two screws in the innermost holes, and compared to stabilization with a six-hole plate with six screws. MAIN OUTCOME MEASURE: Four-point mechanical testing to failure was performed in both apex-dorsal (tension-band) or medial-lateral bending modes. Load-displacement curves were obtained. RESULTS: All of the longer plates with the minimum number of screws were stronger than the six-hole plate with six screws when tested in the medial-lateral and the tension-band mode. The eight-hole plate with four screws, however, was statistically inseparable from the fully loaded six-hole plate. There was no statistical difference between any of the configurations in regard to the stiffness of the fixation. CONCLUSIONS: In a cadaveric ulnar osteotomy model stripped of soft tissue, the number of screws is less important than the length of the plate in providing bending strength to the construct.