Chemosensitive Properties of Electrochemically Synthesized Poly-3-Thienylboronic Acid: Conductometric Detection of Glucose and Other Diol-Containing Compounds under Electrical Affinity Control.

Due to the presence of the boronic acid moieties, poly-3-thienylboronic acid has an affinity for saccharides and other diol-containing compounds. Thin films of this novel chemosensitive polymer were synthesized electrochemically on the gold surface. The adhesion of the polymer was enhanced by the deposition of a monomolecular layer of thiophenol. The technology was used to fabricate conductometric sensors for glucose and other diol-containing compounds. Simultaneous two- and four-electrode conductivity measurements were performed. The chemical sensitivity to sorbitol, fructose, glucose, and ethylene glycol was studied at different pH and electrode potentials, and the corresponding binding constants were obtained. Depending on the electrode potential, the reciprocal values of the binding constants of glucose to poly-3-thienylboronic acid at neutral pH are in the range of 0.2 mM-1.0 mM. The affinity for glucose has been studied in buffer solutions and in solutions containing the major components of human blood. It was shown that the presence of human serum albumin increases the affinity of poly-3-thienylboronic acid for diol-containing compounds.

A review of optical methods for ultrasensitive detection and characterization of nanoparticles in liquid media with a focus on the wide field surface plasmon microscopy.

Development of nanotechnology and corresponding industries during the last decade resulted in a new challenge for analytical science. This includes an ultrasensitive detection and characterization of nanoparticles of different origin and other nanomaterials in various media, including so complex ones as food, biological or environmental samples. The goal of this review is a systematic analysis of possible approaches and description of physical principles behind these methods. The main attention is paid to optical methods which are considered by authors to be mostly effective for the formulated task. Different approaches for detection and analysis of nanoparticles in a volume as well as of those adsorbed on a surface are discussed. While the technologies based on direct analysis of nanoparticle suspensions belong to the established approaches whose development potential has been in large extent exhausted, the novel technologies based on the surface sensing of adsorbed nanoparticles demonstrate intensive development. Therefore, the final part of the review is focused on the wide-field surface plasmon resonance microscopy. It allows one an ultrasensitive detection and characterization of individual nanoparticles of different origin in complex media and provides numerous possibilities for subsequent chemical identification of the detected particles using a hyphenation with other analytical technologies.

Electrically controlled Michael addition: Addressing of covalent immobilization of biological receptors.

Electrically addressed covalent immobilization of biomolecules to the defined electrodes of an electrode array is described. It is based on Michael addition of the thiol group of biomolecules to α,ß-unsaturated carbonyl groups of benzoquinone. This "click" reaction was tested by immobilization of a number of thiolated compounds on the simplest array consisting of two gold electrodes coated by a self-assembled monolayer of benzoquinone-terminated hexanethiol. Electrically controlled binding of hexanethiol, ferrocenylhexanethiol, human serum albumin and thiol-terminated single-stranded DNA (ssDNA) was investigated. The binding was studied using cyclic voltammetry, X-ray photoelectron spectroscopy and surface plasmon resonance. The reaction requires the oxidized state of the benzoquinone moiety; this can be reached by applying of a moderate anodic potential to the electrode. Surface plasmon resonance measurements demonstrated that the thiol-modified ssDNA immobilized by this technique binds complementary synthetic oligonucleotides or PCR-amplified DNA fragments. The developed technology of electrical addressing of covalent immobilization can be applied for fabrication of sensor arrays.

Electrochemical tuning of capacitive response of graphene oxide.

The increasing energy demands of modern society require a deep understanding of the properties of energy storage materials, as well as the tuning of their performance. We show that the capacitance of graphene oxide (GO) can be precisely tuned using a simple electrochemical reduction route. In situ resistance measurements, in combination with cyclic voltammetry measurements and Raman spectroscopy, have shown that upon reduction GO is irreversibly deoxygenated, which is further accompanied by structural ordering and an increase in electrical conductivity. The capacitance is maximized when the concentration of oxygen functional groups is properly balanced with the conductivity. Any further reduction and deoxygenation leads to a gradual loss of capacitance. The observed trend is independent of the preparation route and the exact chemical and structural properties of GO. It is proposed that an improvement in the capacitive properties of any GO can be achieved by optimization of its reduction conditions.

The Role of Anion Adsorption in the Effect of Electrode Potential on Surface Plasmon Resonance Response.

Surface plasmon resonance, being widely used in bioanalytics and biotechnology, is influenced by the electrical potential of the resonant gold layer. To evaluate the mechanism of this effect, we have studied it in solutions of various inorganic electrolytes. The magnitude of the effect decreases according to the series: KBr>KCl>KF>NaClO4 . The data were treated by using different models of the interface. A quantitative description was obtained for the model, which takes into account the local dielectric function of gold being affected by the free electron charge, diffuse ionic layer near the gold/water interface, and specific adsorption of halides to the gold surface with partial charge transfer. Taking into account that most biological experiments are performed in chloride-containing solutions, detailed analysis of the model at these conditions was performed. The results indicate that the chloride adsorption is the main mechanism for the influence of potential on the surface plasmon resonance. The dependencies of surface concentration and residual charge of chloride on the applied potential were determined.

Ionic Referencing in Surface Plasmon Microscopy: Visualization of the Difference in Surface Properties of Patterned Monomolecular Layers.

An approach for visualization of patterned monomolecular layers in surface plasmon microscopy (SPM) is suggested. The development of hidden image in SPM is achieved by referencing of images obtained in the presence of electrolytes with a high molar refraction of either anions or cations. A formation of diffuse layer near the charged surface areas leads to the redistribution of ions. The ratio of SPM images allows one to visualize this redistribution and to distinguish surface areas with different properties. The approach is unobtrusive and robust; it can be used with most surface plasmon resonance (SPR) imaging instruments.

Plasmonic detection and visualization of directed adsorption of charged single nanoparticles to patterned surfaces.

It has recently been shown that surface plasmon microscopy (SPM) allows single nanoparticles (NPs) on sensor surfaces to be detected and analyzed. The authors have applied this technique to study the adsorption of single metallic and plastic NPs. Binding of gold NPs (40, 60 and 100 nm in size) and of 100 nm polystyrene NPs to gold surfaces modified by differently ω-functionalized alkyl thiols was studied first. Self-assembled monolayers (SAM) with varying terminal functions including amino, carboxy, oligo(ethylene glycol), methyl, or trimethylammonium groups were deposited on gold films to form surfaces possessing different charge and hydrophobicity. The affinity of NPs to these surfaces depends strongly on the type of coating. SAMs terminated with trimethylammonium groups and carboxy group display highly different affinity and therefore were preferred when creating patterned charged surfaces. Citrate-stabilized gold NPs and sulfate-terminated polystyrene NPs were used as negatively charged NPs, while branched polyethylenimine-coated silver NPs were used as positively charged NPs. It is shown that the charged patterned areas on the gold films are capable of selectively adsorbing oppositely charged NPs that can be detected and analyzed with an ~1 ng⋅mL-1 detection limit. Graphical abstractSelf-assembled monolayers of ω-functionalized alkyl thiols were deposited on a gold layer of a patterned sensor array. The charge-selective binding of single nanoparticles to such surfaces was registered by wide-field surface plasmon microscopy.

Detection and Quantification of Single Engineered Nanoparticles in Complex Samples Using Template Matching in Wide-Field Surface Plasmon Microscopy.

An ultrasensitive analytical method for direct detection of single nanoparticles in complex environment is described. The method relies on the wide-field surface plasmon microscopy (SPM). The suppression of matrix effects is achieved by image analysis based on the template matching. First, characteristic SPM images of nanoparticles are collected in aqueous suspensions. Then the detection of nanoparticles in complex environment is performed using template matching. Quantification and characterization of nanoparticles size was demonstrated at subppb level (∼100 pg/mL) in such complex media as wines, fruit juices, or cosmetic formulation. Visualization of the nanoparticles is performed in real time. The method does not require any sample pretreatment. If the minimally acceptable adsorption rate is defined as one nanoparticle to the whole sensor surface per few seconds, the working range of the method is ∼106 to 1010 nanoparticles per mL.

Electrically controlled variation of receptor affinity.

A concept of virtual sensor array based on electrically controlled variation of affinity properties of the receptor layer is described. It was realized on the base of integrated electrochemical chemotransistor containing polyaniline as the receptor layer. Electrical control of the redox state of polyaniline was performed in five-electrode configuration containing four electrodes for conductivity measurements and one Ag/AgCl reference electrode. All the electrodes were integrated on the same glass chip. A room-temperature ionic liquid was used for the electrical connection between the reference electrode and chemosensitive material. Conductivity measurements demonstrated effective potential-controlled electrochemical conversions of the receptor material between different redox states. Binding of trimethylamine at three different potentials, corresponding to the different states of the receptor material, was studied. Concentration dependencies and binding kinetics were analyzed. The results demonstrated that the kinetic as well as the equilibrium binding properties of the receptor layer can be controlled by electrical potential, thus providing a possibility to form a virtual sensor array using only a single sensing element. Graphical abstract Single sensing element with electrical control of its affinity can operate as a virtual sensor array.

Individual Detection and Electrochemically Assisted Identification of Adsorbed Nanoparticles by Using Surface Plasmon Microscopy.

The increasing production and application of nanoparticles necessitates a highly sensitive analytical method for the quantification and identification of these potentially hazardous materials. We describe here an application of surface plasmon microscopy for the individual detection of each adsorbed nanoparticle and for visualization of its electrochemical conversion. Whereas the adsorption rate characterizes the number concentration of nanoparticles, the potential at which the adsorbed nanoparticles disappear during an anodic potential sweep characterizes the type of material. All the adsorbed nanoparticles are subjected to the potential sweep simultaneously; nevertheless, each of the up to a million adsorbed nanoparticles is identified individually by its electrochemical dissolution potential. The technique has been tested with silver and copper nanoparticles, but can be extended to many other electrochemically active nanomaterials.

Quantitative turbidity assay for lipolytic enzymes in microtiter plates.

A clearing assay for lipolytic enzymes has been realized in 96-well microtiter plates. A thin layer containing emulsified tributyrin as turbidity-generating substrate was placed on a thicker supporting aqueous layer. Both layers were stabilized by a gel-forming agent. Enzyme addition leads to clearing of the emulsion detected with a standard microtiter plate reader as a decrease of extinction. Dependencies of the signal kinetics on the substrate and enzyme concentrations were studied. For 0.5-1% tributyrin content the reaction rate is not substrate-limited. An initial slope of the signal kinetics is proportional to the lipase activity. A detailed characterization of the assay was performed. Lipolysis of tributyrin was confirmed by glycerol detection. Various gel-forming agents were compared and diffusion conditions in these gels were analyzed. Agar and agarose were found to be the most suitable gel-forming agents, which do not affect enzyme diffusion whereas polyacrylamide gels block lipase diffusion and therefore are not suitable for the assay. The optimized assay prepared from 1% tributyrin emulsion in 2% agar gel was tested with six microbial lipases and porcine pancreatic lipase. The detection limit is 20-60 ng/well which is equivalent to 30 µU/well for T. lanuginosus lipase.

Electroanalytical measurements without electrolytes: conducting polymers as probes for redox titration in non-conductive organic media.

Electroanalytical methods have been applied only in conducting media. An application of conducting polymers allows to overcome this limitation. If such material is in electrochemical equilibrium with dissolved redox active species, its electrical conductivity depends on the redox potential of these species. Therefore, conductometric measurements with conducting polymers can provide about the same information as classical redox electrodes. The approach was applied for redox titration. Equivalent points obtained by this titration in aqueous and organic electrolytes were identical. Then the approach was applied for determination of bromine number by redox titration in non-conducting organic phase.

Self-referencing SPR-biosensors based on penetration difference of evanescent waves.

SPR based biosensors register binding of analytes to the surface with immobilized receptors by measuring changes of the refractive index near this surface. An important task in the improvement of this measurement technology is a separation of signals, corresponding to the changes in the chemosensitive layer, from undesired contributions of bulk phase, for example, due to fluctuations of temperature, concentrations of solutes, pressure. The wavelength of the incident light influences strongly the penetration depth of the corresponding evanescent wave. This dependence was exploited here for compensation of the contribution of the bulk refractive index. It was performed using differential SPR measurements at two wavelengths with differing penetration depths. Theoretical analysis and numerical optimization of the suggested approach, named a Penetration Difference Self-Referencing SPR (PDSR-SPR), were performed. Experimental test was performed using 658 and 980 nm laser diodes. Over 20 times suppression of variations of bulk refractive index with magnitude up to 1000 µRIU was observed. Finally, PDSR-SPR approach was applied for monitoring of antibodies binding to the immobilized antigens.

Chemiresistors based on conducting polymers: a review on measurement techniques.

This review covers the development of measurement configurations for chemiresistors based on conducting polymers. The simplest chemiresistors are based on application of a two-electrode technique. Artifacts caused by contact resistance can be overcome by application of a four-electrode technique. Simultaneous application of the two- and four-electrode measurement configurations provides an internal control of sensor integrity. An incorporation of two additional electrodes controlling the redox state of chemosensitive polymers and connecting to the measurement electrodes through liquid or (quasi)solid electrolyte results in a six-electrode technique; an electrically driven regeneration of such sensors allows one to perform fast and completely reversible measurements.

Integrated electrochemical transistor as a fast recoverable gas sensor.

A new design of conductometric chemical sensors based on conducting polymers as chemosensitive elements was suggested. The sensor includes six electrodes. Four inner electrodes coated by chemosensitive polymer are used for simultaneous two- and four-point resistance measurements thus providing information on the bulk polymer resistance and on the resistance of the polymer/electrode contacts. Two outer electrodes wired to inner electrodes by polymeric electrolyte are used for electrical control of redox state of the chemosensitive polymer. The outer electrodes are connected to potentiostat as reference and counter electrodes. It allows us to control redox state of the inner (working) electrodes. This new measurement configuration, resembling chemosensitive electrochemical transistors, provides an internal test of the sensor integrity and an electrically driven sensor regeneration. It was tested as a sensor for the detection of nitrogen dioxide. Polythiophene or polyaniline was used as receptors. Cyclic voltammograms of these polymers on the sensor surface measured in air atmosphere were very similar to that measured in aqueous electrolyte. A control of conductivity of these chemosensitive polymers by electrical potential applied vs. incorporated reference electrode was demonstrated. This effect was used for the regeneration of the chemosensitive material after exposure to nitrogen dioxide: in comparison to usual chemiresistors displaying an irreversible behavior in such test even in the time scale of hours, a completely reversible sensor regeneration within few minutes was observed.

Soluble neuropilin-2, a nerve repellent receptor, is increased in rheumatoid arthritis synovium and aggravates sympathetic fiber repulsion and arthritis.

OBJECTIVE: In inflammatory lesions, sympathetic nerve fibers disappear soon after the start of inflammation. We identified sympathetic nerve repellents as possible causal agents in rheumatoid arthritis (RA). On nerve terminals, repellent factors bind to neuropilin-2 and its coreceptor. The aim of this study was to investigate the role of neuropilin-2 in the synovial tissue of patients with RA and patients with osteoarthritis (OA) and in experimental arthritis. METHODS: The density of neuropilin-2-positive fibers and cells positive for semaphorin 3F (a sympathetic repellent) was investigated using immunofluorescence staining. Enzyme-linked immunosorbent assay was used to detect soluble neuropilin-2 in body fluids from patients with RA and patients with OA. An axon outgrowth assay and a neuropilin-2 Fc fusion construct (neuropilin-2Fc) were used to investigate semaphorin 3F-induced sympathetic nerve repulsion. In an animal model of type II collagen-induced arthritis, soluble neuropilin-2Fc was studied in vivo. RESULTS: The synovial density of neuropilin-2-positive sympathetic nerve fibers was lower in RA than in OA, but the density of cells positive for semaphorin 3F was similar. In synovial fluid, the level of soluble neuropilin-2 was markedly higher in RA compared with OA. Mouse sympathetic ganglia served as an excellent model with which to study semaphorin 3F-induced nerve fiber repulsion. Neuropilin-2 and its coreceptor were present on sympathetic neurons, and semaphorin 3F bound to neuropilin-2Fc (binding constant 96 nmoles/liter). Semaphorin 3F dose-dependently increased sympathetic nerve fiber repulsion (at a 50% maximum response concentration of 160-210 nmoles/liter). In contrast to our expectations, soluble neuropilin-2Fc did not inhibit repulsion but increased the repellent effect of semaphorin 3F. In experimental arthritis, therapy with neuropilin-2Fc aggravated arthritis. CONCLUSION: Soluble neuropilin-2 has no antirepellent activity but aggravates sympathetic nerve fiber repulsion and arthritis. Increased shedding of neuropilin-2 is probably an unfavorable sign in RA.

The in situ structural characterization of the influenza A virus matrix M1 protein within a virion.

The first attempt has been made to suggest a model of influenza A virus matrix M1 protein spatial structure and molecule orientation within a virion on the basis of tritium planigraphy data and theoretical prediction results. Limited in situ proteolysis of the intact virions with bromelain and surface plasmon resonance spectroscopy study of the M1 protein interaction with lipid coated surfaces were used for independent confirmation of the proposed model.

Analytical applications of electrodes modified by gold nanoparticles: dopamine detection.

Dopamine oxidation was studied on modified gold (nano-Au) electrodes obtained by Layer-by-Layer deposition of gold nanoparticles and polyacrylic acid. A gradual loss of electrochemical activity for the dopamine oxidation reaction is observed at pH 7. Simultaneous SPR spectroscopy and cyclic voltammetry indicate the formation of an adsorbed layer on the electrode surface at this pH value. Investigations, performed through electrochemical and SPR measurements at pH 4, give evidence for a reversible process. At this pH value both dopamine oxidation and reduction current peaks show linear dependence on the dopamine concentration and may be used for analytical applications. The use of the nano-Au electrode allows resolving the peaks corresponding to ascorbic acid and to dopamine oxidation by 240 mV thus providing a high selectively for dopamine detection in the presence of ascorbic acid. The detection limit of this electrode for dopamine is below 4 microM in the presence of 1 mM ascorbic acid. The sensitivity normalized to the macroscopic electrode surface is about 10 mA cm(-2) mM(-1) at sweep rate of 10 V/s.

Conducting polymers in chemical sensors and arrays.

The review covers main applications of conducting polymers in chemical sensors and biosensors. The first part is focused on intrinsic and induced receptor properties of conducting polymers, such as pH sensitivity, sensitivity to inorganic ions and organic molecules as well as sensitivity to gases. Induced receptor properties can be also formed by molecularly imprinted polymerization or by immobilization of biological receptors. Immobilization strategies are reviewed in the second part. The third part is focused on applications of conducting polymers as transducers and includes usual optical (fluorescence, SPR, etc.) and electrical (conductometric, amperometric, potentiometric, etc.) transducing techniques as well as organic chemosensitive semiconductor devices. An assembly of stable sensing structures requires strong binding of conducting polymers to solid supports. These aspects are discussed in the next part. Finally, an application of combinatorial synthesis and high-throughput analysis to the development and optimization of sensing materials is described.